Ideco H44 Drilling Rig for Sale in USA
700 hp Carrier Mounted Drilling Rig
Description
Ideco H44, 700 HP Carrier Mounted Drilling Rig
Drawworks :
Ideco H-44 Single drum, 700 HP, lebus grooved 1-1/8” line, foster
makeup & breakout catheads, air drillers control console, crown-o-matic, brake.
Mast :
Ideco KM108-280, 108’H telescoping derrick, 280,000# SHL, crown block with
sheave cluster & fastline sheave, (2) 3 stage raising rams, hydraulic scoped,
crown safety platform, racking board, tong counterweights, ladder, derrick
climber, standpipe & manifold
Carrier :
All above mounted Ideco rambler tandem axle front & 4 axle rear DIR carrier p/b (2)
caterpillar 3406 diesel engines with electric start, radiator, gauges, (2) Allison transmissions,
(6) hydraulic leveling jacks, fuel tank, hydraulic tank, hydraulic winches, 11’4”W x 42’6”L
mud boat, deadline anchor, 80R22.5 tires
Substructure:
Crown 12’W x 15’H x 32’L with BOP Trolley, Rotary Beams, V-Door Ramp, Stairs, Safety Rails
Pump :
- (Primary) Ideco 800 triplex mud pump, 800 HP with (3) 7” x 9” forged steel fluid ends, Quick
Change Caps, Hydril k-20-500 5,000 psi pulsation dampener, mission 5” x 6” charging pump,
Retsco 3” shear relief valve, rebuilt type D 5000 psi pressure gauge, master skidded with engine.
- Pump Power: Caterpillar D379 diesel engine with air start, radiator, gauges,
shopbuilt 8’W x 34’L pump skid
Rotating Equipment :
Rotary Table - Hacker 20-1/2” rotary table with split master bushings
Swivel - National P-200, 200 ton swivel
Kelly Spinner - Foster hydraulic Kelly spinner
Hex Kelly - 5-1/4” x 40’L hex Kelly
Kelly Drive - Vardo HD Kelly drive bushing square drive
Kelly Valves - 5,000 psi upper Kelly valve, 5000 psi lower Kelly valve
Traveling Equipment :
Ideco 160 ton block/hook combination, 98”L Elevator Links
Well Control Equipment :
BOP - hydril GK-10 Annular Blowout Preventer, 11” x 5M
Drilling spool - 11”ID x 38”H x 5M drilling spool
Accumulator - Shaffer 5 station accumulator with (8) bottles, triplex
pump p/b teco 20hp electric motor, air pump, gauges, lights, skidded,
mounted 7’W x 20’L skid
Remote Control Panel - 4 station mounted doghouse
Choke Manifold - 5000 psi choke manifold with (1) 5 way cross,
(7) 3-1/16” x 5M gate valves, (2) 2-1/16” x 5M manual adjustable chokes, skidded.
Kill valves – (2) 2-1/16” x 5m gate valve
Choke valves – (1) 3-1/16” x 5M gate valve
Houses :
Toolpusher’s House - Shopbuilt 12’W x 41’L toolpushers house with (2) 3’L covered
porches, fully furnished, skidded
Doghouse - Shopbuilt 8’W x 18’L doghouse with 4’L covered porch, (16) lockers,
knowledge box, bench storage, heater, lights, skidded
Mud House – shopbuilt 7’10”W x 20’L with 4’6”L porch, test sink, heater, lights, skidded
Generator/Utility House :
Engine No.1 – KATO A22373002, 210 KW AC Generator p/b Caterpillar 3406 diesel
engine with electric start, radiator, electronic control panel
Engine No.2 – Cat SR-4, 210 KW AC Generator p/b Caterpillar 3408 Diesel Engine with
electric strt, radiator, electronic control panel
Air Compressor – Quincy 390 p/b Siemens 20 HP electric motor
Electrical Control Panel – Square D
Transformer – Hevi-Duty 112.5 KVA
Above mounted on shopbuilt 9’4”W x 29’8”l utility house with lights, skidded
Mud System :
Suction Tank – shopbuilt 10’W x 6’H x 36’L, 370 bbl with 14’L covered porch, (3) compartment,
(3) maxx 2000 mud agitators p/b 7-1/2HP electric motors, flat bottom, internal plumbing,
top mounted walkways, stairs, safety rails, lights, skidded.
Centrifugal Mixing Pump – (2) 5” x 6” centrifugal mixing pumps p/b Siemens 75 HP electric motors
Shaker Tank – shopbuilt 10’W x 6’ h x 39’L, 401 bbl with 10’L covered porch, (3) compartment,
(1) maxx 2000 mud agitator p/b 7-1/2 HP electric motor, flat bottom, internal plumbing, top
mounted walkways, stairs, safety rails, lights, skidded
Centrifugal Mixing pump – mission magnum 5” x 6” p/b 50 hp electric motor
Shale Shaker – National D235-LP-L1 single, single screen linear motion shale shaker
Desander – National DSN-2H-10CTX with (2) 10” cones
Water/Fuel Tanks :
Water Tank – shopbuilt 10’W x 8’H x 20’L, 275 bbl with lights, skidded
Centrifugal Water Pump – mission magnum 2” x 3” p/b teco 20HP electric motor, mounted water tank
Fuel Tank – shopbuilt 8’Dia x 22’L, 8,282 gallon tank with 4’L porch, (2) fuel transfer pumps, skidded
Instrumentation :
Weight Indicator – Model 40, 325,000 lb
Automatic Driller – Satellite
Recorder – Totco 3-Pen
Mud Gauge – 5000 Psi
Handling Tools :
Rotary Tongs – Byron Jackson type B
Elevators – 4-1/2”, 250 Ton BN, CL
Elevators – 7-1/2”, SS, CL
Pipe Slips – (2) 4-1/2”
Collar Slips – 8-Segment, 10-Segment
Safety Clamp – 9-segment
Mud bucket
Ancillary Equipment :
Catwalk – shopbuilt 5’W x 36”H x 51’L with 2-sections, steel deck
Pipe Racks – 3 sets of (6) 42”H x 28’L
Pipe Tubs – (5) shopbuilt 7’4”W x 39’L, skidded
Junk Box – shopbuilt 7’W x 13’4”L
Measuring Device with 15000ft of .092 wireline
Air Hoist – Ingersoll Rand JU40
Pressure Washer EPPS
Rotary Hose – 3-1/2” Dia. X 56’L
Vibrator Hoses – (2) 3-1/2: Dia x 17’L
Drill Line – 3000 ft of 1-1/8”
Rathole & Mousehole
Rig Lights – fluorescent & mercury vapor with wiring
Miscellaneous fire extinguishers, spare parts, hand tools, etc |
