Worldrigs ID: WR435
Specifications
Drawworks :  ALCO 500DD (500 HP) 42” x 10” and 38” x 8” Drum Sizes
Drawworks Power : 1 Caterpillar C-15 (540 HP)
Transmission :  Allison OFS 4700 with Namco Dropbox

Mast : Telescopic Double – 112 feet Internally Guided
Static Hook load Capacity 300,000 pounds

Well Servicing 2 7/8” 18,000 ft. (5,550 Meters)
Workover 3 1/2“ 11,000 ft. (3,350 Meters)
Drilling 4 ½” 9,000 ft. (2,740 Meters)

Substructure
16’ floor Height
Set back Capacity – 300,000 Lbs

Travelling Block : TSM 160 Ton
Swivel : TSM 150 Ton
Rotary Table : Hacker 17 ½” c/w bowl inserts
Mud Pump : One (1) Gardner Denver PZ-7  
Mud Pump Power : Caterpillar C-15 – 540hp 
Transmission : 1 Allison OFS 4700

Mud System
1 Tank System
Tank #1 – 500bbls
1 mixing hopper
 
Solids Control :
One (1) DFTS Mud Conditioner c/w Desilter & Desander

Centrifugal Pumps : One (3) 5 x 6 c/w 60 HP Motor

BOP Equipment
One (1) 11” x 3,000 psi Cameron Townsend Annular
One (1) 11’ x 3,000 psi – 11” x 5,000 psi Crossover Spool
One (1) 11” x 5,000 psi Cameron Townsend Double Gate
One Drilling Spool 11” x 5,000 psi x 11” x 5,000 psi
C/W Choke line valves and Kill line Valves

Choke Manifold
3 1/8” x 5,000 psi Choke Manifold
Two (2) Manual Choke

BOP Closing Unit
4 station, 3000 PSI, 120 Gallon
10 Bottles (12 gallon bottles)

Power Generation : Two (2) Caterpillar C-15 – (50 Hz) (355 kW)
Air Compressors : Two (2) 30HP Rotary Screw Air Compressors c/w filtration system                          
Instrumentation : Weight Indicator. Mud pump and Standpipe Pressure Gauge, Tong Line Torque       
Water /Fuel / Change Room : 100 Barrel Water Tank c/w Two 4 x 3 Centrifugal water Pumps
Catwalk / V Door : 45’ Catwalk with V-door
Pipe Racks : One set of pipe racks
Casing Stabbing Board : Deckard manufactured

Combination Building             
Contains – 4 Station Accumulator, two 30HP Rotary Screw Air Compressor units  c/w
Filtration System, Two caterpillar C-15 – 355 kW Generators

Suitcases : Supply four (4) 10’ Suitcases

Worldrigs ID: WR706
General Rig Data
Rig Data
Year of Construction : 2008
Year of recertification : July 2016 (for one year certification)
Static hook load :200mt
Setback capacity : 113mt

Mast Data
Make : Drillmec
Type : Four legs, open face, two-section telescopic
Clear height from ground level : 36 meter
Clear height from drilling floor : 31 meter

Substructure
Drill floor height : 5.2 meter
Clear height under rotary beam : 4.2 meter
Drilling floor dimensions (meter x meter) : 7 x 5

Drawworks
Make : Drillmec
Type : Conventional
Rated input power (HP) : 1.080
Main drum make : Drillmec
Main drum size (inch x inch) : 26" x 42 1/2"
Main drum static capacity : 24 mt
Main drum clutch : 42 VC 650
Main drum grooved for line OD (inch) : 1 1/8"
Make-up cathead (make) : Drillmech
Break-out cathead (make) : Drillmech
Drill line : 1 1/8" 6 x 19 IWRC EIPS
Brake type : Brake Band
Hydromatic Auxiliary brake make/model : Parmac / V80
Hydromatic Auxiliary brake capacity : 5.000 hp
Hydromatic Auxiliary brake max. pressure : 15 psi
Hydromatic Auxiliary brake max. speed : 1.550 rpm
Hydromatic Auxiliary brake clutch : 26CB 525
Cooling fluid : Water
Crown-O-Matic device : Yes Drillmec

Compound
Air System make : Drillmech
Air compressor engine : Ingersoll Rand T30 mod 2475
Air compressor max. working pressure : 11 bar
Air compressor max. HP in max. WP : 7.1 hp
Air tank capacity : 500 lt
Hydraulic system make : Drillmech

Power Pack
Diesel Engine make/model : Caterpillar / C15 - ACERT
Diesel Engine hoisting power : 540 hp
Diesel Engine quantity : 2 ea
Diesel Engine rate : 2.100 rpm
Automatic gear box quantity : 2 ea
Torque converter : TC680
Hoisting speed : 5 + 1 reverse

Rotary Drive and Rotary Table
Make : Drillmec
Rotary table opening : 271/2"
Max static load on table : 320 mt
Rotary air brake : 16 CB 500
Rotary clutch : 20 CB 500

Hydraulic Winch
Max. Load pull on drilling floor : 3.000 kg
Max. load pull on semi trailer : 5.000 kg

Drilling Equipment
Travelling block - Hook make : American block or equivalent
Travelling block - Hook Working load capacity : 226 mt
Swivel make/model : King Oil Tools/ 6SX or equivalent
Swivel static capacity : 200 mt
Swivel rotating capacity (at 100 rpm) : 122 mt
Swivel working pressure : 345 bar
Hydraulic elevation BOP make : Drillmec
Hydraulic elevation BOP total lifting capacity : 20 ton

Rig Instrumentation
Dead line anchor single pull capacity : 22.6 mt
Dead line anchor load sensor : E80 Tension

Mud System
Make : Drillmec
Volume of shale shaker tank : 60 m3
Volume of intermediate tank : 46 m3
Volume of suction tank : 46 m3
Volume of mixing tank : 60 m3
Water tank : 40 m3

Triplex Mud Pump
Make/Model : Drillmec / 9T1000
Quantity : 2 ea
Design : Horizontal design as per API 7K
Rated Input (HP) : 1.000
Valve Pot size : 7
Mounted on : Oilfield skid

Diesel Engine for Mud Pump
Make/Model : Caterpillar C18 Acert
Engine power : 600hp @ 1.200 rpm
Quantity : 2 ea for each mud pump

Transmission for Mud Pump
Make/Model : Drillmec/TC955 Torque converter

Pulsation Dampener
Make/Model : Hydrill K20-5000 or equivalent
Quantity : 1 ea (for each pump)

Shale Shaker Tank
1. Shale Shaker
Make/Model : Swaco/Mongoose PT
Quantity : 2 ea
Electric motor : 400V - 50Hz ex-proof

2. Mud Cleaner
Make/Model : Swaco / 2-12/6T4/Mongoose PT
Quantity : 1 ea
Electric motor : 400V - 50Hz ex-proof

3. Degasser
Make/Model : Swaco / Vacuum Degasser horizontal type
Quantity : 1 ea
Electric motor : 400V - 50Hz ex-proof

4. Mud Agitators
Make/Model : Swaco / c/w blades
Quantity : 2 ea
Electric motor : 15 KW 400V - 50Hz ex-proof

Intermediate Tank
Centrifugal Pump
Quantity : 2 ea
Used for : Solid equipment
Electric Motor : 75 kW 400V - 50Hz ex-proof

Mud Agitators
Quantity : 2 ea
Electric Motor : 15 kW 400V - 50Hz ex-proof

Suction Tank
1. Supercharging Centrifugal Pump
Quantity : 2 ea
Electric Motor : 75 kW 400V - 50Hz ex-proof

2. Mud Agitators
Quantity : 2 ea
Electric Motor : 15 kW 400V - 50Hz ex-proof

Mixing Tank
1. Mud Agitators
Quantity : 2 ea
Electric Motor : 15 kW 400V - 50Hz ex-proof

Mixing Unit
1. Centrifugal Pump
Quantity : 2 ea
Used for : Solid equipment
Electric Motor : 75 kW 400V - 50Hz ex-proof

2. Hoppers
Quantity : 2 ea
Size : 6"

Trip Tank
1. Quantity / Equipped with : 1 ea / 6 m3 w/ centrifugal pump & electric motor

Poor Boy Degasser
1. Quantity : 1 ea
(Mounted on top of the trip tank complete with inlet and outlet pipes)

Power System
Power Generator
Make/Model : Caterpillar / C15
Quantity : 2 ea
Prime Power : 400ekW-453kW
Frequency : 50 Hz
Speed : 1.500 rpm

MCC- Switch Gear Panel
Quantity : 1 ea
MCC for mud system : 400V / 50Hz
MCC for lighting system : 220V / 50Hz

Air Unit - Utility House
Electric Air Compressor
Pressure at discharge with dryer : 9.8 bar
Pressure at discharge without dryer : 10 bar
Capacity : 95lt/s
Power : 37kW-400V/50Hz
Quantity : 2 ea

Auxiliary Equipment
Water Cooling System
Water Tank Capacity : 5 m3
Water pump flow : 30 m3/h
Water pump motor : 400V/50Hz ex-proof
Quantity : 1 ea

Fuel Tank
Capacity : 60 m3 + 5 m3
Quantity : 1 set

Hydraulic Top Drive (HTD 220)
General Information
Make : Drillmec
Quantity : 1 ea
Bore : 3"
Rated circulating pressure : 5.000 psi - 35 Mpa
Hydraulic system requirement : 868 lt - 35 Mpa
Auxiliary hydraulic system : 225 lt - 55 Mpa

Circulation Swivel
Make : Drillmec
Wash Pipe ID : 3"
Max. WP : 350 bar
Quantity : 1 ea

Rotating Double Hook
Make : Drillmec
Quantity : 1 ea

IBOP Valve
Make : Drillmec
OD : 7 3/4"
ID : 3 1/6"
Working Pressure : 345 bar (5.000 psi)
Quantity : 1 ea
Connection : NC50 box & pin

Top Drive Hydraulic Power Unit
Quantity : 1 ea (Container)
Diesel Engine Quantity : 1 ea
Diesel Engine Make/Model : Caterpillar / C15
Diesel Engine power : 540 hp
Diesel Engine speed : 1.800 rpm
Diesel Engine no. of cylinder : 6 in line

Top Drive Rails
Quantity : 4 ea

Rig Floor Equipment
1. D.P. and D.C. Rotary Tongs
Quantity (no.) : 2 ea
Type : Rotary
Range size from : 3 1/2"
Range size to : 14 3/8"

2. Elevator Links
Set : 1 ea
Length, 1 set : 2 1/4" x 108"
Rated capacity : 250t

Drilling Instrumentation
Drilling Console
Weight Indicator
Mud Pump Pressure Gauges : Pressure range (0-5000 psi)
Rotary Torque Indicator
Rotary speed Tachometer : For top drive
Tong Torque Indicator
Mud Pump Stroke Indicator (Qty) : 2 ea

Others
Dog House (Drillmec made) : 1 ea
Dog House Support : 1 ea
High Pressure Ground Line : 1 ea
Monkey Board : 1 ea
Mud Tanks Walkways : 8 ea
Carrier Walkways : 12 ea
Handrails : 39 ea
Rotary Hose : 1 ea
Mud Pump Discharge Hose : 2 ea
Exhaust : 2 ea
Cable Tray : 1 ea
Suction Line : 1 ea
Stand Pipe Manifold : 1 ea
Stairs : 5 ea
Power Tong & Power Tong Support : 1 ea
BOP Lifting Device Remote Control Panel : 1 ea
Bop Skid & Bop Trolley : 1 ea
Vee Door : 1 ea
Driller Panel : 1 ea
Drilling Recorder 8 Pen : 1 ea
Rig Lightening System : 1 ea
Mud Tanks Lightening System : 1 ea

Well Control Equipment (without valid Certificate) : 1 ea
- 1 ea x 13 5/8" x 5000 psi Annular (Bag Type) BOP
- 1 ea x 13 5/8" x 5000 psi Double Ram BOP (Cameron "U" Type)
- 1 ea x 13 5/8" x 5000 psi Drilling Spool
- 1 ea x 3 1/8" x 5000 psi Armor Covered Flexible Hose
- 1 ea x 3 1/8" x 5000 psi Choke Manifold
- 1 ea x 3 1/8" x 5000 psi Closing Unit
- 1 ea x Remote Control Panel
- 1 ea x Remote Choke Control Panel
- 1 ea x 3 1/8" x 5000 psi HCR Valve

Worldrigs ID: WR500
General
Built : 1985
Full refurbished : 2006

Specifications
Engine: P/B Detroit Series 60 Diesel Engine
Transmission: Allison 5861
Brake: PARMAC 122 Hydraulic Brake C/W Water Tank 300 Gallon

Mast Specifications
Wilson Telescoping Equipped with Rod & Tubing  Boards, Hydraulic Leveling
Jack, Utility Winch, Mounted on Truck 5 Axles Carrier  And Work Platform.
Heights: 96’Capacity: 251,000 LBS
Raveling Block: MCKISSICK83A 100 Ton , c/w (3) 24” Shaves  f/1” Line
1” Tubing Line
Duplex Hook
Tire is new

Condition is very good

Worldrigs ID: WR500
General
Built : 1985
Full refurbished : 2006

Specifications
Engine: P/B Detroit Series 60 Diesel Engine
Transmission: Allison 5861
Brake: PARMAC 122 Hydraulic Brake C/W Water Tank 300 Gallon

Mast Specifications
Wilson Telescoping Equipped with Rod & Tubing  Boards, Hydraulic Leveling
Jack, Utility Winch, Mounted on Truck 5 Axles Carrier  And Work Platform.
Heights: 96’Capacity: 251,000 LBS
Raveling Block: MCKISSICK83A 100 Ton , c/w (3) 24” Shaves  f/1” Line
1” Tubing Line
Duplex Hook
Tire is new

Condition is very good

Worldrigs ID: WR706
General Rig Data
Rig Data
Year of Construction : 2008
Year of recertification : July 2016 (for one year certification)
Static hook load :200mt
Setback capacity : 113mt

Mast Data
Make : Drillmec
Type : Four legs, open face, two-section telescopic
Clear height from ground level : 36 meter
Clear height from drilling floor : 31 meter

Substructure
Drill floor height : 5.2 meter
Clear height under rotary beam : 4.2 meter
Drilling floor dimensions (meter x meter) : 7 x 5

Drawworks
Make : Drillmec
Type : Conventional
Rated input power (HP) : 1.080
Main drum make : Drillmec
Main drum size (inch x inch) : 26" x 42 1/2"
Main drum static capacity : 24 mt
Main drum clutch : 42 VC 650
Main drum grooved for line OD (inch) : 1 1/8"
Make-up cathead (make) : Drillmech
Break-out cathead (make) : Drillmech
Drill line : 1 1/8" 6 x 19 IWRC EIPS
Brake type : Brake Band
Hydromatic Auxiliary brake make/model : Parmac / V80
Hydromatic Auxiliary brake capacity : 5.000 hp
Hydromatic Auxiliary brake max. pressure : 15 psi
Hydromatic Auxiliary brake max. speed : 1.550 rpm
Hydromatic Auxiliary brake clutch : 26CB 525
Cooling fluid : Water
Crown-O-Matic device : Yes Drillmec

Compound
Air System make : Drillmech
Air compressor engine : Ingersoll Rand T30 mod 2475
Air compressor max. working pressure : 11 bar
Air compressor max. HP in max. WP : 7.1 hp
Air tank capacity : 500 lt
Hydraulic system make : Drillmech

Power Pack
Diesel Engine make/model : Caterpillar / C15 - ACERT
Diesel Engine hoisting power : 540 hp
Diesel Engine quantity : 2 ea
Diesel Engine rate : 2.100 rpm
Automatic gear box quantity : 2 ea
Torque converter : TC680
Hoisting speed : 5 + 1 reverse

Rotary Drive and Rotary Table
Make : Drillmec
Rotary table opening : 271/2"
Max static load on table : 320 mt
Rotary air brake : 16 CB 500
Rotary clutch : 20 CB 500

Hydraulic Winch
Max. Load pull on drilling floor : 3.000 kg
Max. load pull on semi trailer : 5.000 kg

Drilling Equipment
Travelling block - Hook make : American block or equivalent
Travelling block - Hook Working load capacity : 226 mt
Swivel make/model : King Oil Tools/ 6SX or equivalent
Swivel static capacity : 200 mt
Swivel rotating capacity (at 100 rpm) : 122 mt
Swivel working pressure : 345 bar
Hydraulic elevation BOP make : Drillmec
Hydraulic elevation BOP total lifting capacity : 20 ton

Rig Instrumentation
Dead line anchor single pull capacity : 22.6 mt
Dead line anchor load sensor : E80 Tension

Mud System
Make : Drillmec
Volume of shale shaker tank : 60 m3
Volume of intermediate tank : 46 m3
Volume of suction tank : 46 m3
Volume of mixing tank : 60 m3
Water tank : 40 m3

Triplex Mud Pump
Make/Model : Drillmec / 9T1000
Quantity : 2 ea
Design : Horizontal design as per API 7K
Rated Input (HP) : 1.000
Valve Pot size : 7
Mounted on : Oilfield skid

Diesel Engine for Mud Pump
Make/Model : Caterpillar C18 Acert
Engine power : 600hp @ 1.200 rpm
Quantity : 2 ea for each mud pump

Transmission for Mud Pump
Make/Model : Drillmec/TC955 Torque converter

Pulsation Dampener
Make/Model : Hydrill K20-5000 or equivalent
Quantity : 1 ea (for each pump)

Shale Shaker Tank
1. Shale Shaker
Make/Model : Swaco/Mongoose PT
Quantity : 2 ea
Electric motor : 400V - 50Hz ex-proof

2. Mud Cleaner
Make/Model : Swaco / 2-12/6T4/Mongoose PT
Quantity : 1 ea
Electric motor : 400V - 50Hz ex-proof

3. Degasser
Make/Model : Swaco / Vacuum Degasser horizontal type
Quantity : 1 ea
Electric motor : 400V - 50Hz ex-proof

4. Mud Agitators
Make/Model : Swaco / c/w blades
Quantity : 2 ea
Electric motor : 15 KW 400V - 50Hz ex-proof

Intermediate Tank
Centrifugal Pump
Quantity : 2 ea
Used for : Solid equipment
Electric Motor : 75 kW 400V - 50Hz ex-proof

Mud Agitators
Quantity : 2 ea
Electric Motor : 15 kW 400V - 50Hz ex-proof

Suction Tank
1. Supercharging Centrifugal Pump
Quantity : 2 ea
Electric Motor : 75 kW 400V - 50Hz ex-proof

2. Mud Agitators
Quantity : 2 ea
Electric Motor : 15 kW 400V - 50Hz ex-proof

Mixing Tank
1. Mud Agitators
Quantity : 2 ea
Electric Motor : 15 kW 400V - 50Hz ex-proof

Mixing Unit
1. Centrifugal Pump
Quantity : 2 ea
Used for : Solid equipment
Electric Motor : 75 kW 400V - 50Hz ex-proof

2. Hoppers
Quantity : 2 ea
Size : 6"

Trip Tank
1. Quantity / Equipped with : 1 ea / 6 m3 w/ centrifugal pump & electric motor

Poor Boy Degasser
1. Quantity : 1 ea
(Mounted on top of the trip tank complete with inlet and outlet pipes)

Power System
Power Generator
Make/Model : Caterpillar / C15
Quantity : 2 ea
Prime Power : 400ekW-453kW
Frequency : 50 Hz
Speed : 1.500 rpm

MCC- Switch Gear Panel
Quantity : 1 ea
MCC for mud system : 400V / 50Hz
MCC for lighting system : 220V / 50Hz

Air Unit - Utility House
Electric Air Compressor
Pressure at discharge with dryer : 9.8 bar
Pressure at discharge without dryer : 10 bar
Capacity : 95lt/s
Power : 37kW-400V/50Hz
Quantity : 2 ea

Auxiliary Equipment
Water Cooling System
Water Tank Capacity : 5 m3
Water pump flow : 30 m3/h
Water pump motor : 400V/50Hz ex-proof
Quantity : 1 ea

Fuel Tank
Capacity : 60 m3 + 5 m3
Quantity : 1 set

Hydraulic Top Drive (HTD 220)
General Information
Make : Drillmec
Quantity : 1 ea
Bore : 3"
Rated circulating pressure : 5.000 psi - 35 Mpa
Hydraulic system requirement : 868 lt - 35 Mpa
Auxiliary hydraulic system : 225 lt - 55 Mpa

Circulation Swivel
Make : Drillmec
Wash Pipe ID : 3"
Max. WP : 350 bar
Quantity : 1 ea

Rotating Double Hook
Make : Drillmec
Quantity : 1 ea

IBOP Valve
Make : Drillmec
OD : 7 3/4"
ID : 3 1/6"
Working Pressure : 345 bar (5.000 psi)
Quantity : 1 ea
Connection : NC50 box & pin

Top Drive Hydraulic Power Unit
Quantity : 1 ea (Container)
Diesel Engine Quantity : 1 ea
Diesel Engine Make/Model : Caterpillar / C15
Diesel Engine power : 540 hp
Diesel Engine speed : 1.800 rpm
Diesel Engine no. of cylinder : 6 in line

Top Drive Rails
Quantity : 4 ea

Rig Floor Equipment
1. D.P. and D.C. Rotary Tongs
Quantity (no.) : 2 ea
Type : Rotary
Range size from : 3 1/2"
Range size to : 14 3/8"

2. Elevator Links
Set : 1 ea
Length, 1 set : 2 1/4" x 108"
Rated capacity : 250t

Drilling Instrumentation
Drilling Console
Weight Indicator
Mud Pump Pressure Gauges : Pressure range (0-5000 psi)
Rotary Torque Indicator
Rotary speed Tachometer : For top drive
Tong Torque Indicator
Mud Pump Stroke Indicator (Qty) : 2 ea

Others
Dog House (Drillmec made) : 1 ea
Dog House Support : 1 ea
High Pressure Ground Line : 1 ea
Monkey Board : 1 ea
Mud Tanks Walkways : 8 ea
Carrier Walkways : 12 ea
Handrails : 39 ea
Rotary Hose : 1 ea
Mud Pump Discharge Hose : 2 ea
Exhaust : 2 ea
Cable Tray : 1 ea
Suction Line : 1 ea
Stand Pipe Manifold : 1 ea
Stairs : 5 ea
Power Tong & Power Tong Support : 1 ea
BOP Lifting Device Remote Control Panel : 1 ea
Bop Skid & Bop Trolley : 1 ea
Vee Door : 1 ea
Driller Panel : 1 ea
Drilling Recorder 8 Pen : 1 ea
Rig Lightening System : 1 ea
Mud Tanks Lightening System : 1 ea

Well Control Equipment (without valid Certificate) : 1 ea
- 1 ea x 13 5/8" x 5000 psi Annular (Bag Type) BOP
- 1 ea x 13 5/8" x 5000 psi Double Ram BOP (Cameron "U" Type)
- 1 ea x 13 5/8" x 5000 psi Drilling Spool
- 1 ea x 3 1/8" x 5000 psi Armor Covered Flexible Hose
- 1 ea x 3 1/8" x 5000 psi Choke Manifold
- 1 ea x 3 1/8" x 5000 psi Closing Unit
- 1 ea x Remote Control Panel
- 1 ea x Remote Choke Control Panel
- 1 ea x 3 1/8" x 5000 psi HCR Valve

Worldrigs ID: WR435
Specifications
Drawworks :  ALCO 500DD (500 HP) 42” x 10” and 38” x 8” Drum Sizes
Drawworks Power : 1 Caterpillar C-15 (540 HP)
Transmission :  Allison OFS 4700 with Namco Dropbox

Mast : Telescopic Double – 112 feet Internally Guided
Static Hook load Capacity 300,000 pounds

Well Servicing 2 7/8” 18,000 ft. (5,550 Meters)
Workover 3 1/2“ 11,000 ft. (3,350 Meters)
Drilling 4 ½” 9,000 ft. (2,740 Meters)

Substructure
16’ floor Height
Set back Capacity – 300,000 Lbs

Travelling Block : TSM 160 Ton
Swivel : TSM 150 Ton
Rotary Table : Hacker 17 ½” c/w bowl inserts
Mud Pump : One (1) Gardner Denver PZ-7  
Mud Pump Power : Caterpillar C-15 – 540hp 
Transmission : 1 Allison OFS 4700

Mud System
1 Tank System
Tank #1 – 500bbls
1 mixing hopper
 
Solids Control :
One (1) DFTS Mud Conditioner c/w Desilter & Desander

Centrifugal Pumps : One (3) 5 x 6 c/w 60 HP Motor

BOP Equipment
One (1) 11” x 3,000 psi Cameron Townsend Annular
One (1) 11’ x 3,000 psi – 11” x 5,000 psi Crossover Spool
One (1) 11” x 5,000 psi Cameron Townsend Double Gate
One Drilling Spool 11” x 5,000 psi x 11” x 5,000 psi
C/W Choke line valves and Kill line Valves

Choke Manifold
3 1/8” x 5,000 psi Choke Manifold
Two (2) Manual Choke

BOP Closing Unit
4 station, 3000 PSI, 120 Gallon
10 Bottles (12 gallon bottles)

Power Generation : Two (2) Caterpillar C-15 – (50 Hz) (355 kW)
Air Compressors : Two (2) 30HP Rotary Screw Air Compressors c/w filtration system                          
Instrumentation : Weight Indicator. Mud pump and Standpipe Pressure Gauge, Tong Line Torque       
Water /Fuel / Change Room : 100 Barrel Water Tank c/w Two 4 x 3 Centrifugal water Pumps
Catwalk / V Door : 45’ Catwalk with V-door
Pipe Racks : One set of pipe racks
Casing Stabbing Board : Deckard manufactured

Combination Building             
Contains – 4 Station Accumulator, two 30HP Rotary Screw Air Compressor units  c/w
Filtration System, Two caterpillar C-15 – 355 kW Generators

Suitcases : Supply four (4) 10’ Suitcases