|
Id: WR660
 Drill Rig for Sale-1.jpg ) Atlas Copco T4BH (Blast Hole) Drilling Rig - for Sale
Worldrigs ID: WR660
Model : T4BH (Blast Hole) Drill Rig
Manufacturer : Atlas Copco
Year : 2006
Condition : Used
Description :
2006 Atlas Copco T4BH (Blast Hole) Drill Rig
Serial Number: 8294
Cummins QSK19 Diesel Deck Engine
IR HR2.5 1250 CFM / 350 PSI Air Compressor
Dual Motor Spur Gear Power Head
LT Long Tower runs (30ft Drill Pipe)
CCC : Cummins isx 15 , 475hp
Location : Middle East Region
|  |
| |
|
Id: WR473
 Atlas Copco RD20 III Drilling Rig for sale
Worldrigs ID: WR473 Details:
Cummins QSK19-C Diesel Deck Engine @ 760 HP 2,800 engine hours since rebuilt
IR HR2.5 / 1250 cfm / 350 psi Air Compressor with mist injection (Estimated500 hours since new)
Power Swivel - High torque rotary head model 4SF-2-12 with 8,000 ft-lbs @120 rpm
In/Out box
Single rod loader
Breakout Wrench - Self-adjusting 20,000 ft-lbs
Extra air manifold
Tool box under cooler
Mast - A500GRB at 62' ft height (Integrated cantilever floor)
120,000 Pullback & 30,000 Pulldown
Bean water injection pump
Mounted on a CCC (Crane Carrier Company) 10 x 6 Truck 5 axle
CAT C13 diesel engine @ 380 HP
44,000 lbs front axle & 69,000 lbs rear axle
Location: USA
| |
| |
|
|
|
Id: WR532
 Atlas Copco T4W DH Drill Rig for Sale
Worldrigs ID: WR532 Model : T4W DH Drill Rig
Manufacturer : Atlas Copco
Model Year : 2005
Condition : Used
Description :
2005 Atlas Copco T4W DH Drill Rig - S/N: 8416
Cummins QSK19 Diesel Deck Engine
IR HR2.5 1250 CFM / 350 PSI Air Compressor
Spur Gear Drive Top Head with 2 Motors
DH (Deep Hole) with 70,000 lbs of Pullback (New Feed Cylinders)
2 Piston bean Water Injection Pump
Set up to run 30’ x 4-1/2” drill rods
4 & 7 & carousels
All New Hydraulic Hoses
New Battery’s
Coolers cleaned and tested
New Paint
Mounted on a CCC (Crane Carrier Company) with Twin-Steer
Cummins M 11
Automatic Transmission
Differential rebuilt
differential lock
New tires on back
VIN#: 1CYDEM5856T047054
Location : USA
| |
| |
|
Id: WR346
 Atlas Copco T3W-70DH Drill Rig in USA
Worldrigs ID: WR346 Model No : T3W-70DH Drill Rig
Manufacturer : Atlas Copco
Model Year : 2007
Condition : Used
Description :
2007 Atlas Copco T3W-70DH Drill Rig
6,000 Hours
DH (Deephole Package) 70,000 LBS Pull Back
New Paint
Newer Tires
Diesel Deck Engine
IR 1070 cfm / 350 psi Air Compressor
Hydraulics Plumbed For Centrifugal Pump
Mounted On A Peterbilt Truck
Diesel Engine
Location : USA
| |
| |
|
|
|
Id: WR479
 Atlas Copco RD20 Range III Drill Rig for Sale
Worldrigs ID: WR479 Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2008
Condition : Used
Description :
2008 Atlas Copco RD20 Range III Drill Rig
Hours on Meter: 916.5
Cummins QSK19 Tier II diesel deck engine rated 755 HP with disconnect
IR HR2.5 series compressor rated 1250 cfm / 350 psi Air Compressor
Range 3 tower package, Rated 120,000 Lbs of pullback force
Hydraulic table jacks
Sixty (60) gallon injection lubricator
Water injection
225 gallon fuel tank
Torque limit control
Storage box under cooler
Diesel fired cold weather starting aid
Note: No Rod Loader & Tooling included
Mounted on a CCC (Crane Carrier Corp) model RD20/10X6 Tridem carrier
2809 Miles on gauge
Caterpillar model C13 diesel engine rated 380 hp
Location : USA
| |
| |
|
Id: WR225
 Atlas Copco RD20 III Drill Rig For Sale
Worldrigs ID: WR225 Model : RD20 III drill rig
Manufacturer : Atlas Copco
Year : 2006
Condition : Used
Description :
2006 Atlas Copco RD20 III drill rig
CAT 3412E Diesel Deck Engine @760HP @1800 RPM
IR HR2.5 1250 cfm / 350 psi Air Compressor
120,000 Pullback & 30,000 Pulldown
Water CAT 3 cylinder Injection Pump - 2520 capacity 25 GPM / 550 PSI max
Mounted on a CCC (Crane Carrier Company) Truck
CAT C13 diesel engine
Drill Pipe available at an extra cost
Location : USA
| |
| |
|
|
|
Id: WR521
 Drill Rig1.jpg) Atlas Copco T4BH (Blast Hole) Drill Rig for Sale
Worldrigs ID: WR521 Condition : Used
Manufacturer : Atlas Copco
Model Year : 2009
Model No : T4BH (Blast Hole) Drill Rig
Decription :
2009 Atlas Copco T4BH (Blast Hole) Drill Rig
Serial Number 8726
IR 1250 CFM / 350 PSI HR2.5 Air Compressor
Cummins QSK19 Diesel Deck Engine
Dual Motor Spur gear power head
LT (Long Tower) to run 30' ft. Drill Pipe
Banana Bar (Angle Drilling)
Rod Changer
Hydraulic Leveling Jacks
Operators Cab
Mounted on CCC (Crane Carrier Company) Truck with Twin Steering
Diesel Engine
Located in Miffliburg, PA yard USA (arriving January 2017)
Note: Can be sold "as is" or will be sold with needed repairs & services at EWD facility
| |
| |
|
Id: WR574
 Drill Rig 1.jpg) Atlas Copco T4BH (Blast Hole) Drill Rig for Sale
Worldrigs ID: WR574 Model : T4BH (Blast Hole) Drill Rig
Manufacturer : Atlas Copco
Model Year : 2009
Condition : Used
Description :
2009 Atlas Copco T4BH (Blast Hole) Drill Rig - Serial Number: 8726
Cummins QSK19 Diesel Deck Engine
IR HR2.5 1250 CFM / 350 PSI Air Compressor
Dual Motor Spur Gear Power Head
LT Long Tower runs (30' Drill Pipe)
Rod Changer
Rear Drillers Cab Enclosure
Hdyraulic Leveling Jacks
Mounted on CCC (Crane Carrier Company) Truck with Twin Steering
Diesel Engine
Note: Can be set up as a T4W (Water Well Drilling) &
Optional DH (Deep Hole Package) at an extra cost
Location : USA
| |
| |
|
|
|
Id: WR299
 Atlas Copco CT20 Diamond Drill Rig for Sale
Worldrigs ID: WR299 Model : CT20 Diamond Drill Rig
Manufacturer : Atlas Copco
Year : 2012
Condition : Used
Description :
2012 Atlas Copco CT20 diamond drill rig
4600 Hours
Cummins QSL9 Tier III Diesel Engine (8.8 liter 224 kw @ 305 hp)
Variable Speed 0 – 1300 rpm
Drilling Angle: Range from 450 to 900
FMC W1122
Fitted with drill break out system using drill head.
Safety cage on the rotation unit and rod holder,
Emergency stop switches, lockable isolation switches,
Track mounting, hydraulic jacks, oil spill plates under engine.
Located in Asia
| |
| |
|
Id: WR485
 Atlas Copco RD20 III Drill Rig for Sale
Worldrigs ID: WR485 Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2006
Condition : Used
Description :
2006 Atlas Copco RD20 III Drill Rig
Cummins QSK19-C Diesel Deck Engine @ 760 HP (2,800 engine hours since rebuilt)
IR HR2.5 / 1250 cfm / 350 psi Air Compressor with mist injection & disconnect (Estimated 500 hours since new)
Power Swivel - High torque rotary head model 4SF-2-12 with 8,000 ft-lbs @120 rpm
In/Out box
Single rod loader
Breakout Wrench - Self-adjusting 20,000 ft-lbs
Extra air manifold
Tool box under cooler
Mast - A500GRB at 62' ft height (Integrated cantilever floor)
120,000 Pullback & 30,000 Pulldown
Bean water injection pump
Mounted on a CCC (Crane Carrier Company) 10 x 6 Truck 5 axle -
VIN#: 1CYDGV5876T047282
CAT C13 diesel engine @ 380 HP
44,000 lbs front axle & 69,000 lbs rear axle
Location : USA
| |
| |
|
|
|
Id: WR661
 Atlas Copco RD20 Range III Drilling Rig - For Sale
Worldrigs ID: WR661
Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2007
Condition : Used
Description :
2007 Atlas Copco RD20 - Range III Drill Rig
120,000 lbs of pullback
Cummins QSK19 Diesel Deck Engine (Very Low Hours)
IR HR2.5 1250 cfm / 350 psi Air Compressor with In/Out box
Rotary Head: 4SV-2-10 Spur gear
Top drive head assembly rated to 8,000 ft. lbs. torque
Single Rod Loader for handling 4.5” o.d. X 30ft long drill rods
Spindle Sub – (4 1/2” x 2 7/8IF")
Water Injection Pump
Hammer Lubricator
Mounted on a CCC (Crane Carrier Carrier) Truck
CAT C13 Diesel Engine
Tooling & Pipe included:
51 (4-1/2 X 30ft X 2-7/8IF") Thread Drill Pipe
12 - (6” X 30ft) Slick Drill Collars
3 - (8” X 30ft) Spiral Drill Collars
Basic Tooling
23 Subs on Steel Platform on Pins
Location : USA
| |
| |
|
Id: WR480
 Atlas Copco RD20 Range III Drill Rig for Sale
Worldrigs ID: WR480 Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2011
Condition : Used
Description :
2011 Atlas Copco RD20 Range III Drill Rig
Hours on Meter: 612.6
Cummins QSK19 Tier II diesel deck engine rated 755 HP With disconnect
IR HR2.5 series compressor rated 1250 cfm / 350 psi Air Compressor
Range 3 tower package, Rated 120,000 Lbs of pullback force
Hydraulic table jacks
Sixty (60) gallon injection lubricator
Water injection
225 gallon fuel tank
Torque limit control
Storage box under cooler
Diesel fired cold weather starting aid
Note: No Rod Loader or Tooling included
Mounted on a CCC (Crane Carrier Corp) model RD20/10X6 Tridem carrier
Miles on Meter: ?
Caterpillar model C13 diesel engine rated 380 HP
Location : USA
| |
| |
|
|
|
Id: WR201
 Atlas Copco T4W Drill Rig for Sale
Worldrigs ID: WR201 Model : T4W Drill Rig
Manufacturer : Atlas Copco
Condition : Used
Year : 2005
Description :
2005 Atlas Copco T4W drill rig
5,130 Low Hours as of 12/2013
IR HR2.5 1250 cfm / 350 psi air compressor
Cummins QSK19C Diesel Deck Engine at 755 HP
50,000 lbs of Pullback
25 GPM CAT 2520 Bean Water Injection Pump
Hammer Lubricator
3 Carousels - (2) 4 Rod & (1) 7 Rod
Worm Gear Head
2 Speed Fan
375' ft of used Steel Drill Pipe (25' x 4 1/2" x 3 1/2") and basic hand tooling included
Lincoln Welder on board
Paint in Very Good Condition
Mounted on a CCC (Crane Carrier Company) truck
CAT C13 Diesel engine @ 380 HP
24,065 Low Miles on gauge as of 12/2013
Location : USA
| |
| |
|
Id: WR484
 Atlas Copco RD20 III Drill Rig for Sale
Worldrigs ID: WR484 Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2006
Condition : Used
Description :
2006 Atlas Copco RD20 III Drill Rig
Cummins QSK19-C Diesel Deck Engine @ 760 HP (2,800 engine hours since rebuilt)
IR HR2.5 / 1250 cfm / 350 psi Air Compressor with mist injection & disconnect (Estimated 500 hours since new)
Power Swivel - High torque rotary head model 4SF-2-12 with 8,000 ft-lbs @120 rpm
In/Out box
Single rod loader
Breakout Wrench - Self-adjusting 20,000 ft-lbs
Extra air manifold
Tool box under cooler
Mast - A500GRB at 62' ft height (Integrated cantilever floor)
120,000 Pullback & 30,000 Pulldown
Bean water injection pump
Mounted on a CCC (Crane Carrier Company) 10 x 6 Truck 5 axle -
VIN#: 1CYDGV5876T047282
CAT C13 diesel engine @ 380 HP
44,000 lbs front axle & 69,000 lbs rear axle
Location : USA
| |
| |
|
|
|
Id: WR475
 Atlas Copco RD20 III XC Drilling Rig for sale
Worldrigs ID: WR475 2011 Atlas Copco RD20 Range III XC Drill Rig
XC tooling included and it is set up as an XC model
Hours on Meter: 10,015.8
Cummins QSK19 Tier II diesel deck engine rated 755 HP With disconnect
IR HR2.5 series compressor rated 1250 cfm / 350 psi Air Compressor
Range 3 tower package, Rated 120,000 Lbs of pullback force
Hydraulic table jacks
Sixty (60) gallon injection lubricator
Water injection
225 gallon fuel tank
Torque limit control
Storage box under cooler
Diesel fired cold weather starting aid
Note: No Basic Hand Tooling (cost extra)
Mounted on a CCC (Crane Carrier Corp) model RD20/10X6 Tridem carrier
Miles on Meter: ?
Caterpillar model C13 diesel engine rated 380 HP
| |
| |
|
Id: WR692
 Atlas Copco T4W DH Drilling Rig - 2006 Built - for Sale
Worldrigs ID: WR692
Model : T4W DH (Deep Hole) Drill Rig
Manufacturer : Atlas Copco
Year : 2006
Condition : Used
Description :
2006 Atlas Copco T4W DH LT Drill Rig - S/N: 8369
Cummins QSK19C Diesel Deck Engine (Tier II)
IR HR2.5 1250/1450 cfm / 350 psi Air Compressor
DH (Deep Hole)
LT (Long Tower) to Handles 30 ft Pipe with 31 ft of Travel
(Note: Does Not Handle Range 2 Casing Pipe)
Water Injection Pump
Foxco Hammer Lubricator
Rod loader (not installed)
Spur Gear Power Head
All new hydraulic hoses
New upper chains
New feed cylinders
Braden 12,000 lb Winch & RKI 2,500 lb Winch
20" Table Open
Mounted on a 2005 CCC Truck - Twin Steer - (VIN: 1CYDEM5855T046923)
CAT C13 Diesel Engine (Tier II)
New tires
New gauges in control panel
Complete New Paint Job in late 2018
Location : USA
| |
| |
|
|
|
Id: WR362
 Atlas Copco DM30-HP Drill Rig for Sale
Worldrigs ID: WR362 Model : DM30-HP Drill Rig
Manufacturer : Atlas Copco
Year : 2006
Condition : Used
Description :
2006 Atlas Copco DM30-HP Drill Rig
Frame Hours = 8636
CAT - C-15 Engine S/N JRE02954 = 1860 hours (Rebuilt at 6776 hours.)
Compressor - S/N 70882Y06AG - 900 CFM @ 350 PSI
Water Injection
Angle Package
4 " O.D. X 30 ft. Steels - 5 additional new steels included.
Manuals / some spare parts / top subs, ect. also included.
Mounted on a Track Carrier
Location : USA
| |
| |
|
Id: WR94
 Atlas Copco T3W Water well drilling rig for Sale
Worldrigs ID: WR94 Model : T3W drill rig
Manufacturer : Atlas Copco
Year : 2008
Condition : Used
Description :
2008 Atlas Copco T3W drill rig
1200 Low Hours
CAT C15 Diesel Deck Engine @ 580 HP
IR 1170 cfm / 350 psi Air Compressor (in & out box)
40,000 lbs of Pullback
Bean 18 GPM Water Injection Pump - 4 cylinders
Hammer Lubricator
8000 ft. lb power head
18000 lb. hoist
Hydraulic Welder & Generator on board
Rod Rack
9 Rod Carousel handles (20' x 3-1/2" x 2-3/8" IF) drill pipe
4 Hydraulic Leveling Jacks
Mounted in a 2009 International Truck
CAT C12 Diesel Engine @ 420 HP
3,000 miles on gauge
Location : USA
| |
| |
|
|
|
Id: WR522
 Atlas Copco RD20 Range III XC Drill Rig
Worldrigs ID: WR522 Condition : Used
Manufacturer : Atlas Copco
Model Year : 2014
Model No : RD20 III XC Drill Rig
Decription :
2014 Atlas Copco RD20 Range III XC Drill Rig - S/N: 21453
Note: Drill Rig doesn't have the XC tooling, but it is set up as an XC model
Hours on Meter: 5,558.3
Cummins QSK19 Tier II diesel deck engine rated 755 HP With disconnect
IR HR2.5 series 1250 cfm / 350 psi Air Compressor
Range 3 tower package & Rated 120,000 lbs of pullback force
Hydraulic table jacks
Sixty (60) gallon injection lubricator
Water injection pump
225 gallon fuel tank
Torque limit control
Storage box under cooler
Diesel fired cold weather starting aid
Note: No Rod Loader or Tooling included (cost extra)
Mounted on a CCC (Crane Carrier Corp) model RD20/10X6 Tridem carrier
VIN#: 1CYDG8683ET051261
Caterpillar model C13 diesel engine rated 380 HP
Located in SW Region, USA
| |
| |
|
Id: WR476
 Atlas Copco RD20 III Drilling Rig for sale
Worldrigs ID: WR476 SOLD
Details:
2012 Atlas Copco RD20 Range III Drill Rig
Hours on Meter: 9,290
Cummins QSK19 Tier II diesel deck engine rated 755 - with disconnect
IR HR2.5 series compressor rated 1250 cfm / 350 psi Air Compressor
Range 3 tower package, Rated 120,000 Lbs of pullback force
Hydraulic table jacks
Sixty (60) gallon injection lubricator
225 gallon fuel tank
Torque limit control
Storage box under cooler
Diesel fired cold weather starting aid
Note: No Rod Loader or Tooling included
Mounted on a CCC (Crane Carrier Corp) model RD20/10X6 Tridem carrier
12,478.9 Miles on gauge
Caterpillar model C13 diesel engine rated 380 HP
| |
| |
|
|
|
Id: WR472
 Atlas Copco RD20 III Drilling Rig for sale
Worldrigs ID: WR472 Details:
2006 Atlas Copco RD20 III Drill Rig
Cummins QSK19-C Diesel Deck Engine @ 760 HP 2500 hours since rebuilt
IR HR2.5 / 1250 cfm / 350 psi Air Compressor with mist injection (500 hours since new)
Power Swivel - High torque rotary head model 4SF-2-12 with 8,000 ft-lbs @120 rpm
In/Out box
Single rod loader
Breakout Wrench - Self-adjusting 20,000 ft-lbs
Extra air manifold
Tool box under cooler
Mast - A500GRB at 62' ft height (Integrated cantilever floor)
120,000 Pullback & 30,000 Pulldown
Bean water injection pump
Mounted on a CCC (Crane Carrier Company) 10 x 6 Truck 5 axle
CAT C13 diesel engine @ 380 HP
44,000 lbs front axle & 69,000 lbs rear axle
Location: USA
| |
| |
|
Id: WR474
 Atlas Copco RD20 III Drilling Rig for sale
Worldrigs ID: WR474 Details:
2008 Atlas Copco RD20 Range III Drill Rig
Hours on Meter: 916.5
Cummins QSK19 Tier II diesel deck engine rated 755 HP with disconnect
IR HR2.5 series compressor rated 1250 cfm / 350 psi Air Compressor
Range 3 tower package, Rated 120,000 Lbs of pullback force
Hydraulic table jacks
Sixty (60) gallon injection lubricator
Water injection
225 gallon fuel tank
Torque limit control
Storage box under cooler
Diesel fired cold weather starting aid
Note: No Rod Loader & Tooling included
Mounted on a CCC (Crane Carrier Corp) model RD20/10X6 Tridem carrier
2809 Miles on gauge
Caterpillar model C13 diesel engine rated 380 hp
| |
| |
|
|
or call +65 97768837. 
