|
Id: WR406
 1974 Built Speedstar SS200 Drill Rig for Sale
Worldrigs ID: WR406 Model : SS200 Drill Rig
Manufacturer : Speedstar
Year : 1974
Condition : Used
Description :
1974 Speedstar SS200 Drill Rig
1 Owner
Gaso 7-1/2" duplex mud pump (new sleeves & pistons in 2015)
hydraulic pull down
3 leveling jacks
400' ft drill pipe
8-1/2" inch rotary table
Mounted on 1974 Ford LT9000 Truck
Cummins Diesel Engine with (3732 hours)
Can drill any where from 6-12"+ inches diameter boreholes
Location : USA
|  |
| |
|
Id: WR281
 Speedstar 30K Drilling Rig for Sale
Worldrigs ID: WR281 Model : Speedstar
Manufacturer : 30K Drill Rig
Year : 1989
Condition : Used
Description
1989 Speedstar 30K Drill Rig
CAT 3408-C Diesel Deck Engine (2 years since installed and 2300 hours)
Sullair 900/350 CFM newly (rebuilt with 1 hour since)
18,000 lbs main winch
2000 lbs Sandline
Pipe Spinner
Mounted on a 1989 Ford L 9000
CAT 3406B Diesel Engine
Transmission: Road Ranger RTO 14708LL 8 Speed
Miles: 125,139
(20' x 3.5") & 600' ft of Drill Pipe
6 pipe non-mounted carosel
Mounted on a 1989 Ford L 9000 Truck
Location : USA
| |
| |
|
|
|
Id: WR492
 Speedstar S S61A Drilling Rig for sale
Worldrigs ID: WR492 Speedstar S S61A Cable Tool Rig Details:
Rebuilt jack shaft with new bearings, clutches, and spudding gear
Weighted Double pitman walking beam
New shaft & bushing in spudder pulley
3 hydraulic jacks
Single or double line
Casing line or extra after market Hydraulic winch
Rig Engine:
163 Continental
4 sp. Trans., new 5V power belt (new)
Derrick:
48 feet with 18 new 20-W Bucyrus shocks
Elevator to about 20 feet
Truck:
1963 International 4x4
345 cu. V-8 engine
Less than 30k miles
4 sp. trans.
New 8:25 x 20 steel belted tires
Front axle 5020 lbs.
Rear axle 12,060 lbs.
Power brakes
No CDL required to drive
| |
| |
|
Id: WR217
 Speedstar 30K Drill Rig for Sale
Worldrigs ID: WR217 Model : 30K Drill Rig
Manufacturer : Speedstar
Year : 2004
Condition : Used
Description :
2004 Speedstar 30K drill rig
Sullair 1000 cfm / 350 psi Air Compressor
3,500 Hours +
Hammer Oilier
6 Rod Carousel
Bean 20 GPM Water Injection Pump
Break Out Wrench and Rod Spinner
2 Winches
Mounted on a Peterbilt Truck
CAT C15 diesel engine at 550 HP
Fuller 8 Speed Transmission
97,750 miles
(32) Drill Pipe (20' x 4 1/2" x 2 7/8" IF) Cost Extra
Location : USA
| |
| |
|
|
|
Id: WR345
 Speedstar SS210 Drill Rig for Sale
Worldrigs ID: WR345 Model : SS210 Drill Rig
Manufacturer : Speedstar
Year : 1972
Condition : Used
Description :
1972 Speedstar SS210 Drill Rig
180' ft of 20' ft drill pipe
400' ft of 25' ft drill pipe with trailer
pump wet air compressor on board
mud pump - mounted on a skid
2x20' ft drill collars
A stabilizer, various subs
bits & miscellaneous parts
Location : USA
| |
| |
|
Id: WR405
 Gefco/Speedstar 185k Drill Rig & Drilling Package - For Sale
Worldrigs ID: WR405 Manufacturer : Gefco
Year : 2007
Model No : 185K Drill Rig
Condition : Used
Description :
2007 Gefco/Speedstar 185k Drill Rig & Drilling Package
Top Head Drive (185,000 Lbs Of Pullback & 30,000 Lbs Of Pull Down)
Cat C15 Diesel Engine @ 550 Hp
Electric Start
Gauges & Safety Shut Off
51' H Vertical Working Space Tower (Hydraulically Raised)
Working Lights
8,000 Lbs Hydraulic Utility Winch
Hydraluic Act DP & DC Loader
Drillers Console
Mounted On A 2007 Kimble 5-Axle Carrier Truck - Vin#: 1k91aphd37208137
Folding Walkways & Steps & Safety Railings
(4) Hydraulic Leveling Jacks
Fuller 18 Speed Transmission With Drop Box
445/65r22.5 Front, 11r/22.5 Rear Tires, Disc Wheels
Sold as a package which includes:
(1) 10'6"W X 20'l Back-On Mud Boat
(1) 10'6"W X 29'l Back-On Ramp
(1) 8'h X 10'6"W X 10'l Work Floor With Folding Walkways, Saftey Rails, Skidded
8'w X 36'l Round Top Generator House: Olympia 200kw Ac Generator Model
D200-P3 P/B Perkins 3000 Diesel Engine, Switch Gear, Lighting Panels
& Controls Mounted, Skidded
8'w X 40'l Round Top Doghouse Constructed In 3 Sections,
Doghouse With Knowledge Box, Bench Storage, Storage Shelves, Change House
With Lockers & Storage Facilities, Parts & Mechanical Room, Work Bench Parts
Storage, Area For Repairs & Maintenance, Heater & Lights, Mounted On A 2007
Stanton Dynamics T/A Trailer - Vin: 1s9sf41238s834114, 8'w X 40'l W/ Stairways,
Folding Walkways, Safety Railings, 11r/22.5 Tires, Disc Wheels
40"H X 8'w X 36'l Back-On Doghouse Ramp, Skidded
Soap/Fuel House 8'w X 36'l, 3400 Gallon Fuel Cap With Double Hull, (2) 10-Bbl.
Cap Soap Tanks, (2) Meyers Model C-35-20b Soap Pump P/B (1) 30 Hp Electric
Motor, (1) Hydraulic Powered, Lubester, Heater, Lights, Skidded.
7'8"W X 35'l Center Tub With Catwalk, Skidded
30"H X 7'8"W X 35'l Junk Box, Skidded.
Location USA
| |
| |
|
|
|
Id: WR305
 Gefco / Speedstar 30K-DH Drill Rig for Sale
Worldrigs ID: WR305 Model : 30K-DH Drill Rig
Manufacturer : Gefco
Model Year : 2007
Condition : Used
Description :
2007 Gefco / Speedstar 30K-DH Drill Rig
Sullair 1050 cfm / 350 psi Air Compressor
Water Injection Pump
Hammer Lubricator
Hydraulic Leveling Jacks
Mounted on a 2006 Peterbuilt 357 Truck
CAT C15 Diesel Engine (Rebuilt in 2012)
Location : N.E. Region
| |
| |
|
Id: WR491
 Speedstar 275 Drilling Rig for sale
| |
| |
|
|
|
Id: WR449
 Speedstar SS-22 Mud Rotary Drill Rig for Sale
Worldrigs ID: WR449 Model : SS22 Drill Rig
Manufacturer : Speedstar
Model Year : 1978
Condition : Used
Description :
1978 Speedstar SS-22 Mud Rotary Drill Rig
Hours: 4,941
Chassis Information:
- 4 Axles
- Crane Carrier 8x4 w/ Cummins N14 Work Platform
Drawworks / Mast Information:
- Speedstar
- 2 Drums
- Hydro-matic brake
- Max Hook Load:80,000 lb
- Mast Length: Handles 40’ casing
- Mast Racking board
Drilling Equipment:
- 7 1⁄4 x 10 Gardner Denver
- FXO172
- 10” GD retractable rotary table
- Mud Kelly with bushing
Tools & Support Equipment:
- Drill pipe 4 1⁄2 od with flats, 3 1⁄2 IF" ID 82 joints x 20’ = 1640’
- 5 joints misc collars X 20’ +/-
- Pipe trailer 20 ft flatbed, 5 ft dove tail, tandom axle 22,500 lbs Bit subs and handling tools
- Little Giant Swivel 3" Pipe
- Pipe spinner
- Tongs - Web Wilson
- Extra crown assembly and transmission Chain and pull down mechanism + misc parts
Location : USA
| |
| |
|
Id: WR165
 Speedstar SS-15 II Drill Rig for Sale
Worldrigs ID: WR165 Model : SS-15 Drill Rig
Manufacturer : Speedstar
Year : 1977
Condition : Used
Description :
1977 Speedstar SS-15 II Drill Rig
Mounted on a 1977 GMC Truck
13 Speed transmission
Rig Serial #: 7154
4 1/4" Kelly
18 GPM John Bean water injection system
Double Drum Drawworks with air clutches
Sandreel
Table Drive
750 cfm / 300 psi Sullair air compressor/low hours installed prior to purchase in 2002
C60 Engine, Easy start, runs great, burns no oil
Table Drive, 8 1/2" opening, hydrostatically driven
Air Controls
Easy load, Rod tray with 17 pieces of 3-1/2" API x 4-1/2" OD x 20' Rods (340')
in rack + 25 foot Kelly Bar/365' ft total
Line oiler, electric/air
4 hydraulic leveling Jacks
35' mast height above table
Safety Shut Down
Machine runs exceptionally well
6" Bit basket
10" Bit basket
Pipe rollers
Drill Rod Clamps
Chain Wrench
260' ft of additional drill rod available at an extra cost
Location : USA
| |
| |
|
|
|
Id: WR157
 Speedstar Mini-Star Drill Rig for Sale
Worldrigs ID: WR157 Model : Mini-Star Drill Rig
Manufacturer : Speedstar
Year : 1989
Condition : Used
Description :
1989 Speedstar Mini-Star Drill Rig
Sullair 200 CFM development air compressor
John Deere diesel deck engine
Mission Sand Master 4x3 centrifugal mud pump
Single rod loader
Mounted on a 2006 International 4300 single rear axle truck (213,000 miles)
Tophead rebuilt
All newer hydraulic hoses
2 newer and 1 rebuilt hydraulic pumps
Added Sand Guzzler by Mud Puppy
Factory rebuilt Mission 4x3 centrifugal mud pump
250' ft of used drill pipe (15' x 2-3/8" IF) few bits & sub adapters included
Location : USA
| |
| |
|
Id: WR535
 Speedstar 275 Quick Drill rig for Sale
Worldrigs ID: WR535 Model : Speedstar
Manufacturer : 275 Quick Drill rig
Year : 1984
Condition : Used
Description :
1984 Speedstar 275 Quick Drill rig - S/N: 101159
Mounted on a 1984 International Truck 4x4 - VIN#: 1HTAR1854CHA11269
IHC DT466 Diesel Engine
Gardner Denver 5x6 Duplex Mud Pump (hydraulic driven)
Joy screw type 250 cmf / 150 psi Air Compressor - 0070-7095-0039 S/N: 146100
Beam Water Injection Pump
5 Rod Carousel
Sandline
300' ft of Drill Pipe (3" x 2-3/8" Reg Thread) & Tooling (table pieces, lifting plug, wrenches) included
Recent Repairs & Services:
New motor top drive power head
New gear box and 3 pumps
New hydraulic 20’ ft cylinder to head
Sandblasted and Painted
Weight 40,000 lbs & 31'2" L x 8'6" W X 12'4" H & 25'6" needed in Well.
Location : USA
| |
| |
|
|
|
Id: WR275
 Speedstar 275 Quickdrill Drilling Rig For Sale
Worldrigs ID: WR275 Model : 275 Quickdrill Rig
Manufacturer : Speedstar
Year : 1986
Condition : Used
Description :
1986 Speedstar 275 Quickdrill Rig
4X3X13 Centrifugal Mud Pump
Leroi compressor 50SDS (rebuilt in 2000)
Main Winch & Sandline
Single Rod Loader
Rod Rack
(16) 2-3/8" IF x 15' ft drill pipe and 6" inch stabilizer
Mud pan and suction line
4 hydraulic leveling jacks
Mounted on a newer 1992 GMC Topkick Truck
CAT Diesel Engine
10 Speed Transmission
4 newer rear tires
203000 miles
Location : USA
| |
| |
|
Id: WR448
 Gefco/Speedstar Jed-A Reverse Circulation Drill Rig - for Sale
Worldrigs ID: WR448 Model : Jed-A Reverse Circulation Drill Rig
Manufacturer : Speedstar
Model Year : 1978
Condition : Used
Description :
1978 Gefco/Speedstar Jed-A Reverse Circulation and Mud Rotary Drill Rig
Trailer Information:
- 3 Axles
- Engine Hours: 14,091
- John Deere Diesel: 225 hp
Drawworks / Mast Information:
- Drawworks Model: Gefco
- Max Hook Load: 80,000 lbs
Drilling Equipment:
- 5-1/2 X 8 FWI Pump
- 18" Rotary Table GD retractable
- Western Hydro Swivel: 6WC with 6” RC Kelly with bushings
Tools & Support Equipment:
- Little Giant Swivel 3" with mud kelly and bushing
- Drill Pipe - Mud Rotary- 4-1/2" OD bottle neck, 4-1/2
- IF” :: 39 joints x 25’ = 975’ 2 joints 7” 6 5/8" reg collars x 27” and misc piping
- Weber pipe trailer with dog house
- 10’ with blow off head
- Misc subs and tongs Air lifting head
- Rotary table bushings
- 5-1/2" IF elevators
- Slips
- 25’ dual swab
- Reverse circulation Kelly and swivel
- Drill Pipe - Reverse
- 5-1/2 IF 5” ID drill pipe x 20' x 45 each
- 10’ 5-1/2" IF, 5” ID drill pipe x 2 each
- 5” ID 8” OD drill collars x 6-5/8 x 17’(+/-) x 3 each
Location : USA
| |
| |
|
|
or call +65 97768837. 
