|
Id: WR487
 Ingersoll-Rand TH60 Drilling Rig for sale
Worldrigs ID: WR487 Details:
IR 750 cfm / 250 psi air compressor
38’ tower (hydraulically raised with boom)
7 rod carousel for (4-1/2 OD x 20’ drill pipe)
29,500 lbs of pullback,
16,000 lbs winch
Hydraulic top head drive with twin motors
Water Injection pump
Auxiliary winch
Three hydraulic leveling jacks
Air driller’s console controls
Cotta gear box
Hydraulics
Mounted on a newer 1988 GMC General tandem axle truck
Detroit 8V92 diesel engine
Fuller RTO-9513 13 speed transmission
425/65R22.5 front and 11.00R-20 rear tires
|  |
| |
|
Id: WR120
 Ingersoll-Rand T3W - Long Tower Drilling Rig for Sale
Worldrigs ID: WR120 Model : T3W - Long Tower
Manufacturer : Ingersoll-Rand
Year : 1990
Condition : Used
Description :
1990 Ingersoll-Rand T3W drill rig - S/N: 3280
IR 900 cfm / 350 psi air compressor (Rebuilt with 2,500+ hours since)
Cummins 855 Diesel Deck Engine at 450 hp (Rebuilt with 800+ hours since)
18 GPM bean water injection pump
pre-heat box (cold weather starter)
37' ft Long Tower
24,000 lbs pulldown & 26,500 lbs pullback
Hydraulic Break Out Wrench
Pipe Rack
4 Hydraulic Leveling Jacks
260' ft of Drill Pipe (20') & Basic Tooling included
Mounted on a International Paystar 5000 Truck
Cummins 350 HP Diesel Engine
32,000+ miles
Location : USA
| |
| |
|
|
|
Id: WR606
 Ingersoll-Rand T4W Drilling Rig - 1980 Built for Sale
Worldrigs ID: WR606
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1980
Condition : Used
Description :
1980 Ingersoll-Rand T4W Drill Rig
IR 600 cfm / 250 psi Air compressor
Detroit 8V71N Diesel Deck Engine
Single motor spur gear head
7x4 Rod Carousel
675' ft of 4-1/2”x 25' FT Thread 2-7/8" IF Drill pipe
Updated Hydraulic pumps
10 GPM Piston bean water injection pump
Basic tools
Mounted on 1977 CCC (Crane Carrier Company) Truck
Detroit 6V53T Diesel Engine
RTO613 Transmission
Location : USA
| |
| |
|
Id: WR593
 Ingersoll-Rand T4W Drill Rig - 1985 Built For Sale
Worldrigs ID: WR593
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1985
Condition : Used
Description :
1985 Ingersoll-Rand T4W Drill Rig (Modified)
Note: Rebuild based on T4W tower and control panel
Mounted an 1980 International 2574 truck (brand new steer tires)
Elgi 1150 cfm / 350 psi Air Compressor
3 hole Funk box
Detroit V-12 on diesel deck engine
Note: Not wore out by any means but drill has been sitting 7-8 years, can be
pre-lubed and all hoses replaced included for an additional $10k.
Included as a Package:
80 joints of T4W pipe
Ingersoll-Rand 1050 CFM / 350 PSI Auxiliary Compressor (Detroit 12V71TT Diesel Engine,
Allison transmission, air start, fuel tank). needs gasket replaced on separator tank.
Another Spare Detroit 12V71TT Diesel Engine
58 joints of 25' ft Mayhew Jr. drill pipe
Location : USA
| |
| |
|
|
|
Id: WR572
 Ingersoll-Rand T4W Drill Rig for Sale
Worldrigs ID: WR572 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1978
Condition : Used
Description :
1978 Ingersoll-Rand T4W Drill Rig
Detroit 8V Diesel Deck Engine
IR 750 cfm / 150 psi Air Compressor
Worm Gear Power Head
Carousel
2 New Hydraulic Pumps installed
Hydraulic Leveling Jacks (Rear Jacks Repaired)
Serviced Recently
Mounted on a CCC (Crane Carrier Company) Truck
Detroit 6V Diesel Engine
350’ ft of Drill Pipe, bits, 6” DTH Hammer, Tooling Included
Tires estimated 80% +-
Location : Southern Region
| |
| |
|
Id: WR73
 Ingersoll-Rand T4W DH Used Drill Rig for Sale
Worldrigs ID: WR73 Model : T4W DH drill rig
Manufacturer : Ingersoll-Rand
Year : 1988
Condition : As-IS
Description :
1988 Ingersoll-Rand T4W DH Drill Rig - S/N: 2837
Cummins 855 Diesel Deck Engine (would have to be removed if air compressor
installed & higher HP engine needed)
Note: No Air Compressor on Board (Can be installed at an extra cost with 900/350 or
1050/350 or 1250/350)
Note: Set up to connect a portable air compressor or mud pump for drilling
Note: No Hammer Lubricator or Water Injection Pump (can be installed at an extra cost)
70,000 lbs of Pullback DH (Deep Hole)
5,812 Hours
7 Rod Carousel
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
VIN: 1CYDCM284JT0366646
57,064 miles & 4,210 Hours on Truck
Note: Can be sold "As Is" or Retrofitted with deck engine, air compressor, etc installed.
Repairs & Services cost extra
Location : USA
| |
| |
|
|
|
Id: WR551
 Ingersoll-Rand T3W Drill Rig for Sale
Worldrigs ID: WR551 Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1998
Condition : Used
Description :
1998 Ingersoll-Rand T3W Drill Rig
CAT 3406 Diesel Deck Engine
IR HR2 900 cfm / 350 psi Air Compressor
Hammer Lubricator
Bean water injection pump (4 piston)
7885 hours
18,000 LBS Winch
400' ft of (4-1/2” x 20’ 2-7/8IF) drill pipe & basic tooling included
Pipe Rack
Hydraulic leveling jacks
Mounted on 1998 International 2600 Truck
VIN# 1HTGLATT8XH631062
33,148 miles
Caterpillar C-10 diesel engine - rated 350 HP
Jake brakes
10 Speed Spicer Transmission
Power divider
Tires (90%+ Very Good Condition)
Location : USA
| |
| |
|
Id: WR123
 Ingersoll-Rand TH55 Cyclone Drilling Rig for Sale
Worldrigs ID: WR123 Model : TH55 Cyclone
Manufacturer : Ingersoll-Rand
Year : 1975
Condition : used
Description :
1975 Ingersoll-Rand TH55 drill rig
Detroit 671 Diesel Deck Engine
600 cfm / 140 air compressor (Vain)
Meyers Water Injection
Venture Hammer Oilier
300' ft of used drill pipe (15' x 4 1/2 x 2 7/8") included
Mounted on a Truck
Detroit 6V53 Diesel Engine
Location : USA
| |
| |
|
|
|
Id: WR96
 Drill Rig for Sale - 1.jpg ) Ingersoll-Rand T3W DH (Deep Hole) Drill Rig for Sale
Worldrigs ID: WR96 Model : T3W DH (Deep Hole)
Manufacturer : Ingersoll-Rand
Year : 1998
Condition : Used
Description:
1998 Ingersoll-Rand T3W DH (Deep Hole) Drill Rig
CAT 3406 Deck Engine
Meter Reads 9,000 Hours
30,000 LB Pullback
IR 900 CFM / 350 PSI Air Compressor
18,000 LB Winch
High Torque Head
Diesel Preheater
9 GPM Bean Water Injection
Hammer Oiler
7 Rod Carousel Standing
260' Side Carousel Lay-Down
Installed: New Pullback Cylinder, Head Rollers, And Sheave Bushings Recently
1,000’ of (3 ½ API X 20') Drill Pipe & Basic Tooling Included
Mounted on International 2674 Truck
CAT C-10 Diesel Engine
310 HP
10 Speed Transmission
Jake Brakes
Rear Lockers
25,000 Miles as of 7-1-2012
20k Front Axle 40K Rear Axle
Location : USA
| |
| |
|
Id: WR248
 Ingersoll-Rand RD20 III Drill Rig for Sale
Worldrigs ID: WR248 Model : RD20 III Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2004
Condition : used
Description :
2004 Ingersoll-Rand RD20 III drill rig - S/N: 6880
Caterpillar 3412E diesel deck engine @ 760 HP
IR HR2.5 1250 cfm / 350 psi Air Compressor
Rebuilt - Power Head (0 hours since)
(2) New Cylinders installed
120,000 lbs of pullback
1 rod carousel
60 gallon DHD Hammer Lubicator
25 GPM CAT water injection pump
Hydraulic Leveling Jacks
Mounted on a CCC (Crane Carrier Company) Truck - Tridem Carrier (5 axles)
CAT C13 Diesel Engine
8 Speed Transmission with Low Low
All New Tires (0 miles since installed)
Complete New Paint Job finished in July 2016, Repairs & Services included
Location : USA
| |
| |
|
|
|
Id: WR315
 Ingersoll-Rand T4W DH Drill Rig for Sale in USA
Worldrigs ID: WR315 Model : Ingersoll-Rand T4W DH Drill Rig
Year : 2015
Condition : New
Description :
Ingersoll-Rand T4W DH Drill Rig (Rebuilt in 2015)
New (0 hours) Caterpillar C18 Diesel Deck Engine
New (0 hours) Ingersoll-Rand HR2.5 1170 CFM / 350 PSI Air Compressor
Rebuilt Spur Gear Drive Top Head
Brand New Chain, Sprockets and bushings
Brand New 70,000 LBS feed cylinders
7x4x4 Rod carousel carries 400' ft of (4-1/2” X 25’) drill pipe
New gear box 4-hole
New hydraulic pumps
All hydraulic motors rebuilt
All hydraulic valves rebuilt
New hoses
All cylinders rebuilt or replaced with new
Coolers Have been clean and tested
New Winches and new cable installed
All valves Rebuilt or Brand New
New Gauges
Mounted on a New 2015 CCC (Crane Carrier Company) Truck with twin-steer
New Cummins Diesel Engine
12R22.5 Tires
Location : USA
| |
| |
|
Id: WR495
 Ingersoll-Rand RD20 III Used Drilling Rig for Sale
Worldrigs ID: WR495 Model : RD20 Range III Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2002
Condition : Used
Description :
2002 Ingersoll-Rand RD20 III
IR HR2.5 / 350 psi @ 1250cfm Air Compressor
Cummins QSK19 deck engine
Clutch
Rotary Head: 4SV-2-10 Spur gear, top drive head assembly rated to 8,000 ft. lbs. torque
Range 3 tower package rated to 120,000 lbs. pullback.
7 rod carousel for handling 4.5”O.D. X 30’ long drill rods.
DHD Lubricator
25 GPM Water Injection Pump
Mounted on: Crane Carrier 8 X 4 chassis with Cummins 305 diesel engine.
Location : Asia
| |
| |
|
|
|
Id: WR608
 Ingersoll-Rand T4W Drilling Rig - For Sale
Worldrigs ID: WR608
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1996
Condition : Used
Description :
1996 Ingersoll-Rand T4W Drill Rig
IR 900 cfm / 350 psi Air Compressor
CAT 3406 Deck Diesel Engine
Spur Gear Head
Hammer lubricator
10 GPM Bean Water Injection
Mounted on CCC (Crane Carrier Company) Truck
Cummins L10 Truck Diesel Engine
8 LL Transmission
Location : USA
| |
| |
|
Id: WR524
 Ingersoll-Rand T4W DH Drill Rig for Sale
Worldrigs ID: WR524 Condition : Used
Manufacturer : Ingersoll-Rand
Model No : 30K-DH (Deep Hole) Drill Rigole) Drill Rig
Model Year : 1981
Decription :
1981 Ingersoll-Rand T4W DH Drill Rig - S/N: 14008
Cummins QSK19 Diesel Deck Engine
IR HR2 - 1050 cfm / 350 psi Air Compressor
DH (Deep Hole) with 70,000 lbs of Pullback
Carousel
300' ft of used Drill Pipe (25' x 4-1/2" x 3-1/2" API) & basic tooling included
Rotary Head (recently rebuilt)
3 Hydraulic Leveling Jacks
Mounted on a CCC (Crane Carrier Company) Truck - VIN: 1CYDCG28XBT030255
Diesel Engine
Location : USA
| |
| |
|
|
|
Id: WR483
 Ingersoll-Rand T4W Drill rig 2004 Built for Sale
Worldrigs ID: WR483 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2004
Condition : Used
Description :
2004 Ingersoll-Rand T4W Drill rig
IR HR2.5 1250 cfm / 350 psi Air Compressor
Cummins QSK 19 Diesel Deck Engine
50,000 LBS of pull back
Spur gear power head
25 GPM CAT Water Pump
Diesel Fired Pre-heater
Casing Winch
5 Gallon Oiler
Mounted on a CCC (Crane Carrier Company)
CAT C12 Diesel Engine
Total hours: 7,241
Location : USA
| |
| |
|
Id: WR571
 Ingersoll-Rand TH75W Drill Rig For Sale
Worldrigs ID: WR571 Model : TH75W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1992
Condition : Used
Description:
1992 Ingersoll-Rand TH75W Drill Rig (set up for water well drilling)
Cummins KTA19-C Diesel Deck Engine - S/N 37141244
IR HR2 900 cfm / 350 psi Air Compressor
6 Rod Carousel
Bean Water injection (Head missing)
7221.5+ hours on Meter
est 300' ft of Drill Pipe (20' x 4-1/2") & basic tooling included
4 Hydraulic Leveling Jacks
Mounted on Ford L9000 Truck
VIN# IFDZU90XONVA30165
23,737.8 Miles
CAT 3406 Diesel Engine - rated 400 HP - S/N 3ZJ23533
Good tires
Notes: Compressor cooler has moisture on bottom, Lots of rust on the
under frame,
No major leaks. Complete New Paint Job Cost: $8,500 USD
Location : USA
| |
| |
|
|
|
Id: WR249
 Ingersoll-Rand T4W DH drill rig For Sale
Worldrigs ID: WR249 Model : T4W DH drill rig
Manufacturer : Ingersoll-Rand
Condition : Used
Year : 2000
Description :
2000 Ingersoll-Rand T4W DH (Deep Hole) drill rig & Package
IR H2.5 1250 cfm / 350 psi Air Compressor (Rebuilt April 2013 @ 11,392+ hours)
Cummins QSK 19 diesel deck engine – partial rebuild - New ECM (April 2014), New Injectors (November 2012), New seal kit on engine (June 2014)
DH (Deep Hole) Package with 70,000 lbs of Pullback
Spur Gear Rotary Head – Rebuilt 10-25-2014 @ 12,500+ hours
7 rod carousel, 4 rod storage rack (set up for 4-1/2" OD drill pipe)
Torque Limit Control
In-line Oiler DHD
25 GPM water injection
Cold Weather Start Aid
2 speed fan
20” diameter table opening
Pulldown cylinders rebuilt
Hydraulic pumps rebuilt in June 2014
New Funk Gear Box
Mounted on a 6x4 CCC (Crane Carrier Company) Truck
CAT 3306C Diesel Engine with 300 hp
Fuller Transmission
110 Volt Block Heater (truck Engine)
Newer Tires all around (installed around summer 2015)
Included in the partial drill package:
975' ft of drill pipe (25' x 4-1/2")
8" Drill Collar
Included in the complete drill package:
Late model Mud Puppy MP 255-400 Mounted on a Trailer with diesel engine
26" Hole Opener
17-1/2" TCI Bit
(2) - 20" Drag Bits
14" Bits
| |
| |
|
Id: WR542
 Ingersoll-Rand T3W Drill Rig for Sale
Worldrigs ID: WR542 Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2001
Condition : Used
Description :
2001 Ingersoll-Rand T3W Drill Rig
IR 1050 cfm / 350 psi Air Compressor
CAT C15 Diesel Deck Engine
Rebuilt Power Head (Sand master & 2 speed) & Swivel
New cables bushings on shives top and bottom
360' feet of drill pipe (20' x 4-1/2") included
Mission Magnum 3x4 Centrifugal Pump (hydraulic driven)
Water Injection Pump
Carousel
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a International Truck
Diesel Engine
Needs Paint
Location : USA
| |
| |
|
|
|
Id: WR587
 Ingersoll-Rand T4W Drill Rig for Sale
Worldrigs ID: WR587 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used
Description
1994 Ingersoll-Rand T4W Drill Rig
Cummins KTA19C Diesel Deck Engine
IR 1050 cfm / 350 psi Air Compressor
Worm Gear Power Head
4 & 7 Rod Carousels
14,570 hours
Water Injection Pump
Hammer Lubricator
50,000 lbs of Pullback
Included as a package:
2000' ft of (4.5" x 25') drill pipe, 6" & 8" & 10" drill collars,
used 6" & 8" Hammers & Bits, Handling Plates,
Breakout Wrenches, Petal Tongs
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
21,830 Miles
Location : USA
| |
| |
|
Id: WR106
 Ingersoll-Rand T4W Water Well Drill Rig for Sale
Worldrigs ID: WR106 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1986
Condition : Used
Description :
1986 Ingersoll-Rand T4W drill rig
Cummins KT19 Diesel Deck Engine (Rebuilt in 2007 with 2,620 hours since)
IR 900 cfm / 350 psi Air Compressor (Rebuilt in 2007 with 2,620 hours since)
Spur Gear Power Head
4 & 7 Rod Carousel
Newer Hydraulic Pump & Cooling Fan Drive Motor
1,100' ft of Used Drill Pipe (25' x 4-1/2" x 3-1/2") & basic tooling included
Mounted on a CCC (Crane Carrier Company) Truck
Cummins L10 Diesel Engine
8 Speed Transmission
Location : USA
| |
| |
|
|
|
Id: WR453
 Ingersoll-Rand RD20 Range II Drill Rig for Sale
Worldrigs ID: WR453 Description:
IR HR2.5 - 1250 cfm / 350 psi Air Compressor
Cummins QSK19C Diesel Deck Engine
2,246 Hours on gauge (not original)
Cat 2520 water injection pump
Hammer Lubricator
110,000 lbs of Pullback
Floating Sub
Cat Walks
Hydraulic Leveling Jacks
Mounted on a CCC (Crane Carrier Company) Truck with 4 Axles
Cummins M11 Diesel Engine
8,785 Miles on gauge
New Paint Job in October 2016
Rebuilt tower lift cylinders, rebuilt power head, rebuilt feed cylinders, many hoses replaced, pullback cables are new, new double stack pump, and completely serviced
| |
| |
|
Id: WR591
 Ingersoll-Rand T4W Drill Rig For Sale
Worldrigs ID: WR591 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1987
Condition : Used
Description :
1987 Ingersoll-Rand T4W Drill Rig
Cummins KTA19 diesel deck engine (purchased from Cummins with 2930 hours - Reman)
IR 900 cfm / 350 psi air compressor (6000 hours)
50,000 lbs of pull back
Head is worm gear (re-built in 2015)
225' ft of Drill Pipe (Currently uses 3-1/2“ x 25‘)
7 and 4 Rod Carousels
Hammer Lubricator
4 piston water injection pump
Mounted on a Hendrickson Carrier Truck
Diesel Engine
82,000 miles
5” used hammer included
Location : USA
| |
| |
|
|
|
Id: WR124
 Ingersoll-Rand TH75 Used Drill Rig for Sale
Worldrigs ID: WR124 Model : TH75 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1991
Condition : Used
Description :
1991 Ingersoll-Rand TH75 Drill Rig
About 12,500 - 13,000 total frame hours
Cummins KT19 Diesel Deck Engine at 525 hp
IR 900 cfm / 350 psi Air Compressor (10,000 hours estimated on Feb 2014)
4x3 mission centrifugal pump (no motor, not being used now)
50,000 lbs of Pullback
recently rebuilt swivel, Cotta box
newer pull down cables
set up for (3 1/2" or 4 1/2" x 20') drill pipe
newer paint & very well maintained
Cost Extra: About 2,000' ft of (20' x 3-1/2" x 2-3/8" IF) & 200' ft of 20' x 4-1/2" x 2-7/8")
used drill pipe available at additional cost
Mounted on a Paystar 5000 Truck
Diesel Engine
10 speed transmission with low low gears
mileage 45,000 about
Location : USA
| |
| |
|
Id: WR379
 Ingersoll-Rand T4W DH Drill Rig - 1999 Built - for Sale
Worldrigs ID: WR379 PENDING SALE
Model : T4W DH (Deep Hole) Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1999
Condition : Used
Description :
1999 Ingersoll-Rand T4W DH (Deep Hole) Drill Rig
IR H2.5 1050 cfm / 350 psi Air Compressor
Cummins QSK 19 diesel deck engine
DH (Deep Hole) Package with 70,000 lbs of Pullback
Worm gear power head
7 rod carousel
4 rod storage rack (set up for 4-1/2" OD drill pipe)
Torque Limit Control
In-line Oiler DHD
25 GPM water injection
2 speed fan
20” diameter table opening
Mounted on a 6x4 CCC (Crane Carrier Company) Truck
Cummins M11 Diesel Engine
Fuller Transmission
Location : USA
| |
| |
|
|
|
Id: WR576
 Drill Rig1.jpg) Ingersoll-Rand T4BH (Blast Hole) Drill Rig for Sale
Worldrigs ID: WR576 Model : T4BH (Blast Hole) Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1999
Condition : Used
Description :
1999 Ingersoll-Rand T4BH (Blast Hole) Drill Rig
S/N: 7434
Cummins QSK19 Diesel Deck Engine
1050 cfm / 350 psi Air Compressor
Hammer Oiler
Cat Water Injection Pump
37,500 lbs of Pullback
2 Motor Spur Head
4456 hours on meter
5 Rod Carousel
Mounted on a CCC (Crane Carrier Company) Truck
CAT 3306 Diesel Engine
8,741 Miles on gauge
Location : USA
| |
| |
|
Id: WR505
 Ingersoll Rand T3W Drill Rig - 1988 Built - for Sale
Worldrigs ID: WR505 Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1988
Condition : Used
Description :
1988 Ingersoll Rand T3W Drill Rig
Reman Cummins NTA 855 Diesel Deck Engine (2004)
IR 825 cfm / 350 psi Air Compressor
12500 Hours
Water Injection Pump - 18 GPM
Hydraulic Leveling Jacks
Pipe Rack
Mounted on a 1988 L8000 Ford Truck
Diesel Engine
51,150 Miles on gauge
Location : USA
| |
| |
|
|
|
Id: WR62
 Ingersoll-Rand DM-M2 Drill Rig (Blast Hole) for Sale
Worldrigs ID: WR62 Model : DM-M2 Drill Rig (Blast Hole)
Manufacturer : Ingersoll-Rand
Year : 2001
Condition : Used
Description :
2001 Ingersoll-Rand Drill DM-M2 Drill Rig (Blast Hole)
Meter Reads 35,316 hours
Note : Tower Cylinder & Hydraulic Pumps were rebuilt about 3500 hours
CAT 3412 Diesel Engine
IR 1250 cfm / 350 psi Air Compressor
Spur Gear Power Head
Carousel
4 Hydraulic Leveling Jacks
Inside Cab with A/C & Heater & Control Station
Note: Drilling Capacity in diameter 9 7/8 "to 10 5/8" Maximum depth 54 meters
Location : USA
| |
| |
|
Id: WR74
 Ingersoll-Rand T4W Drill Rig for Sale
Worldrigs ID: WR74 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1978
Condition : Used
Description :
1978 Ingersoll-Rand T4 drill rig
IR 750 cfm 150 psi Air Compressor
Detroit 8V92 Turbo Diesel Engine (Rebuilt in 2010)
Hours 800
50,000 lbs of Pullback
Spur Gear power head with single motor
Carousel - 5 Rods
Drill pipe 230m (4 1/2" x 25' )
Bean Water Injection Pump
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
Location : Southern Europe
| |
| |
|
|
|
Id: WR220
 Ingersoll-Rand TH60 Drill Rig for Sale
Worldrigs ID: WR220 Model : TH60 Drill Rig
Manufacturer : Atlas Copco
Year : 1993
Condition : Used
Description:
1993 Ingersoll-Rand TH60 Drill Rig
IR 750 cfm / 250 psi Air Compressor
4 Hydraulic Leveling Jacks
Pipe Rack
Includes casing hammer hoist cylinder and jib boom (casing hammer not included)
Long Tower
7 rod carousel
29,500 lbs of pullback
CAT 12 GMP water injection pump
6,250 / 4,650 ft/lbs of Torque (2 speed 128/170 RPM) AC Spur Power Head
16,000 lbs Main Winch & 2,000 lbs Sandreel
Mounted on a Paystar 5000 International Truck
Cummin N14 Diesel Engine @410 HP
8 Speed Eaton Transmission
Miles 54,8208
16,480 Frame Hours
Location : USA
| |
| |
|
Id: WR488
 Ingersoll-Rand TH60 Drilling Rig for sale
Worldrigs ID: WR488 Details:
IR 750 cfm / 250 psi air compressor
38’ tower (hydraulically raised with boom)
7 rod carousel for (4-1/2 OD x 20’ drill pipe)
29,500 lb. pullback
6,000 lbs winch
Hydraulic top head drive with twin motors
Water Injection pump
Auxiliary winch
Three hydraulic leveling jacks
Air driller’s console controls
Cotta gear box
Hydraulics
Mounted on a newer 1996 Ford LT9000 tandem axle truck
Detroit Series 60 diesel engine
Fuller RTO-9513 13 speed transmission
425/65R22.5 front and 11.00R-20 rear tires
| |
| |
|
|
|
Id: WR378
 Ingersoll-Rand T3W Drill Rig - For Sale
Worldrigs ID: WR378 Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2005
Condition : Used
Description :
2005 Ingersoll-Rand T3W Drill Rig
S/N#: 6920
Caterpillar C-15 Diesel Deck Engine - S/N: BEM04469
IR 1070 cfm / 350 psi Air Compressor
8000 Hours
300' ft of (20' x 3-1/2" x 2-3/8IF) included
Carousel
Pipe Rack
Water Injection Pump
Hammer Lubricator
hydraulic leveling jacks
Mounted on a 2005 International 7600 Truck
Diesel Engine
32,501 miles
VIN#: 1HTWYSBT95J003179
Location : USA
| |
| |
|
Id: WR506
 Ingersoll Rand T4W Drill Rig for Sale
Worldrigs ID: WR506 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1977
Condition : Used
Description :
1977 Ingersoll Rand T4W Drill Rig
Cummins 855 Diesel Deck Engine
Ingersoll Rand 750 cfm / 250 psi Air Compressor
50,000 Lbs of pull back
Worm gear power head
Pig Hammer lubricator
Water injection pump
7 x 4 Rod Carousels
Auxiliary winch
Webasto engine heater
Mounted on 1977 CCC (Crane Carrier Chassis) VIN# IR84599Y24793
Cummins L-10 Diesel Engine
Location : USA
| |
| |
|
|
|
Id: WR527
 Ingersoll-Rand T4W DH (Deep Hole) Drill Rig for Sale
Worldrigs ID: WR527 Model : T4W DH (Deep Hole) Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2003
Condition : Used
Description :
2003 Ingersoll-Rand T4W DH (Deep Hole) Drill Rig
Unused (New, never used is claimed by the drill owner)
1250 CFM / 350 PSI Air Compressor
Cummins QSK19 Diesel Deck Engine
70,000 lbs of pullback
Spur Gear Top Head Drive (Single Main Motor)
Braden 8,000 lbs winch
CAT 25 GPM Water Injection Pump
3X4X13 Centrifugal Mud Pump
Mounted on a CCC (Crane Carrier Company) Truck - All wheel drive (6x6)
Location : Northern Africa Region
| |
| |
|
Id: WR534
 Ingersoll Rand TH-55 Drill Rig for Sale
Worldrigs ID: WR534 Model : TH-55 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1987
Condition : Used
Description
1987 Ingersoll Rand TH-55 Drill Rig
IR 650 cfm / 250 psi air compressor (new in 2010)
3x4 variable mud pump
Water injection
Main line and sand reel
9 rod carousel
Rod rack
Recent Repairs: New transfer case 2016 & New quad drive in 2015
Comes with 500’ ft of (3-½” x 20’ x 2-3/8 IF) drill pipe
Mounted on a newer 2001 Sterling LT-9513 Truck
Cumming ISM 330 diesel engine (rebuilt in 2014)
301,600 miles show on speedometer
Both rig and truck are in excellent condition, and are daily workers.
Location : USA
| |
| |
|
|
|
Id: WR556
 Drill Rig 1.jpg) Ingersoll-Rand T4BH (Blast Hole) Drill Rig for Sale
Worldrigs ID: WR556 Model : T4BH (Blast Hole) Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1998
Condition : Used
Description :
1998 Ingersoll-Rand T4BH (Blast Hole) Drill Rig - S/N: 6340
Cummins QSK19 Diesel Deck Engine (Rebuilt 0 Hours)
IR HR2.5 1250 CFM / 350 PSI Air Compressor (Rebuilt 0 Hours)
Spur Gear Power Head with 2 Motors
(Rebuilt Feed Cylinders)
2 Piston Bean Water Injection Pump
5 Rod Carousel
New Batteries
Mounted on a CCC (Crane Carrier Company) Truck
Cummins M11 Diesel Engine
Jake brakes
Differential lock
VIN#:1CYDCL482WT043550
Location : USA
| |
| |
|
Id: WR105
 Ingersoll-Rand RD10 Drill Rig with Package for Sale
Worldrigs ID: WR105 Model : RD10 Rig Package
Manufacturer : Ingersoll-Rand
Year : 1982
Condition : Used
Description :
1982 Ingersoll-Rand RD10 drill rig
1050 cfm / 350 psi Air Compressor (needs to be rebuilt or replaced as it runs hot)
Cummins KT19 Diesel Deck Engine (3,500 hours since rebuilt)
Spur Gear Head (3,500 hours since rebuilt)
CAT 2520 water injection
2 winches
Single rod loader
Mounted on a Pettybone Truck - Twin Tandem Axle
13 speed transmission
Detroit 6V71 diesel engine
Newer Cables
Tires 70% good
| |
| |
|
|
|
Id: WR295
 Ingersoll-Rand T4W Drilling Rig For Sale
Worldrigs ID: WR295 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1984
Condition : Used
Description :
1984 Ingersoll Rand T4W Drill Rig
Detroit 12V71TT Diesel Deck Engine
IR 900 cfm / 350 psi Air compressor
Worm gear power head
50,000 LBS of pull back
Hammer oilier
2 piston bean water injection pump
Mounted on CCC (Crane Carrier Company) Truck
CAT 3208 Diesel Engine
Location : USA
| |
| |
|
Id: WR555
 Ingersoll-Rand T4W Drill Rig for Sale
Worldrigs ID: WR555 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Condition : Used
Model Year : 1975
Description :
1975 Ingersoll-Rand T4W Drill Rig - S/N: 11355
Detroit 12V71N Diesel Deck Engine
IR 750 cfm / 250 psi air compressor
10 GPM Bean Water Injection Pump
Hammer Lubricator
Worm Gear Power Head
300' ft of Drill Pipe (4-1/2” x 25') and basic tooling included
4 & 7 Rod Carousels
Winches
3 Hydraulic Leveling Jacks
Mounted on a CCC (Crane Carrier Company) Model IR 845-AX Truck
Detroit 6V53 N Diesel Engine
Nice condition
Location : USA
| |
| |
|
|
|
Id: WR91
 Ingersoll-Rand DM25SP, Rotary Blast hole Drill Rig for Sale
Worldrigs ID: WR91 Model : DM25SP, Rotary Blast hole Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1996
Condition : Used
Description :
1996 Ingersoll-Rand DM25SP, Rotary Blast hole Drill Rig
Powered by Cummins N14 Diesel Engine @ 450 HP
Down The Hole (DTH) Single Pass
IR HR2 - 800 cfm / 350 psi Air Compressor
Starts and Moves but not operational
operating weight of 30,000kg
5,000 lb pull down and
Dual pole battery isolators lockable
Ground level emergency stops
Heldweld safe access steps (retractable)
600mm cab access walkways etc.
MDG 15 compliances
Location : Australia
| |
| |
|
Id: WR90
 Ingersoll-Rand DM25SP Rotary Blast hole Drilling Rig for Sale
Worldrigs ID: WR90 Model: DM25SP Rotary Blast hole Drill Rig
Manufacturer: Ingersoll-Rand
Year: 1994
Condition: Used
Description :
1994 Ingersoll-Rand DM25SP Rotary Blast hole Drill Rig
Down The Hole (DTH) Single Pass
Meter Reads 8,754 Hours
A/C Rops
Powered by Cummins NTA 855C Diesel Engine @ 450 HP
IR HR2 850 cfm / 350 psi Air Compressor
750/300 Air Compressor
Dual pole battery isolators lockable
Ground level emergency stops
Heldweld safe access steps (retractable)
600mm cab access walkways etc.
MDG 15 compliances
Location : Australia
| |
| |
|
|
|
Id: WR529
 Ingersoll-Rand RD20 Range II Rotary Drill Rig for Sale
Worldrigs ID: WR529 Manufacturer : Ingersoll-Rand
Model Year : 2000
Model No : RD20 II Drill Rig
Condition : Used
Description :
2000 Ingersoll-Rand RD20 Range II Rotary Drill Rig
IR 1050 cfm / 350 psi Air Compressor
Cummins 700 HP Diesel Deck Engine
Spur Gear Power Head with 2 double motors
110,000 lbs of Pullback
Floating Sub Adapter
3 hydraulic leveling jacks
Carousel
Mounted on a CCC (Crane Carrier Company) Truck
Cummins M11 Diesel Engine @ 450 HP
13 Speed Transmission
Cost Extra or Included as a Package:
1985 Joy Booster WB12 Air Booster 2 Stage - S/N: 12585
SOC 2400 B
Detroit 12V71 Diesel Engine
Skid Mounted
Location : USA
| |
| |
|
Id: WR454
 Ingersoll-Rand RD20 Range II Drill Rig for Sale
Worldrigs ID: WR454 Model : RD20 II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1993
Condition : Used
Description
1993 Ingersoll-Rand RD20 Range II Drill Rig - S/N: 3987
Cummins KTA19 Diesel Deck Deck Engine @ 600 HP
7 Rod Carusel
Cat 2520 water injection pump
Hammer Lubricator
Hydraulic Leveling Jacks
Mounted on a 1993 Central Manufacturing Truck with 4 axles
Cummins L10 Diesel Engine
VIN number: PGV84002
Note: No Air Compressor on board as of now (was a IR 1050/350)
Location : USA
| |
| |
|
|
|
Id: WR610
 Ingersoll-Rand TH60 Drilling Rig - 1989 Built - for Sale
Worldrigs ID: WR610
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1989
Condition : Used
Description :
1989 Ingersoll-Rand TH60 Drill Rig
Ingersoll-Rand 825 cfm / 350 psi Air Compressor
Gardiner Denver 5x6 Duplex Power Mud Pump
Pulse Injection Pump 1lt/min - rated 70bar
Cat Water pump 38 lt/min - rated 69 Bar
Gearmatic Winch Model 35 single speed with automatic brake and free-fall attachment 12000 kg @22 metres /min.
Capacity 112 metres of 14mm cable
Weldco Casing Hammer
Pulldown (30,000lbs) 13,610 kg. & Holdback (30,000lbs) 13,000kg
Rotation torque (60,000 in-lb) 692 kg-m & Rotation speed 0-100 rpm
Mounted on a Hendrickson Truck (8x6) 6 wheel drive
Detroit 8V92TA V8 Diesel Engine - rated 427 hp
400' ft of drill pipe & tooling & spare parts are included
Location : Western Region, Europe
| |
| |
|
Id: WR71
 Ingersoll-Rand T4W DH Drill Rig for Sale
Worldrigs ID: WR71 SOLD
Model : T4W DH Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1996
Condition : Used
Description :
1996 Ingersoll-Rand T4W DH Drill Rig
IR HR2.5 1250 CFM/350 PSI Air Compressor
Cummins QSK19 Diesel Deck Engine
Worm Gear head
DH (Deep Hole) with 70,000 lbs of pullback
Hammer oilier
Water injection
P7 hydraulic pump - Rebuilt
4 & 7 rod carousels
Mounted on CCC (Crane Carrier Company) Truck
Cummins M-11 Diesel Engine
76,000+ Miles
Location: USA
| |
| |
|
|
|
Id: WR605
 Ingersoll-Rand T4W Drill Rig - For Sale
Worldrigs ID: WR605
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1998
Condition : Used
Description :
1998 Ingersoll-Rand T4W Drill Rig
Cummins KT19 diesel deck (10,000 hours)
IR HR2 900 cfm / 350 psi air compressor
50,000 lbs of pullback
has a worm gear head
7 & 4 Rod Carousels
limit control
Bean water injection pump
Hammer Lubricator
Includes 300’ ft of drill pipe (25' x 4-1/2") and basic operating hand tools
Mounted on a CCC (Crane Carrier Company) Truck
CAT Diesel Engine
Jake brakes
Location : USA
| |
| |
|
Id: WR586
 Ingersoll-Rand T3W Drill Rig for Sale
Worldrigs ID: WR586 Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used
Description :
1994 Ingersoll-Rand T3W
CAT 3406C diesel deck engine (7,000 hours since rebuilt)
IR 825 cfm / 350 psi Air Compressor (4,300 hours since rebuilt)
8,000 lb rotary head
7 rod carousel
rod box
25 GPM Water Injection Pump
Hammer Lubricator
18,000 lb single line winch
Newer Tires
Newer Paint
Mounted on a Ford L9000 Truck
CAT 3176 diesel engine
Eaon 13 speed transmission
9,106 miles on odometer (may be incorrect)
Note: Rig was thoroughly reconditioned by manufacture in 2015 and has only been
used a few hours since
Location : USA
| |
| |
|
|
|
Id: WR575
 Drill Rig1.jpg) Ingersoll-Rand T4BH (Blast Hole) Drill Rig for Sale
Worldrigs ID: WR575 Model : T4BH (Blast Hole) Drill Rig
Manufacturer : Ingersoll-Rand
Condition : Used
Year : 1995
Description :
1995 Ingersoll-Rand T4BH (Blast Hole) Drill Rig
S/N: 7186
Cummins N14 Diesel Deck Engine
900 cfm / 350 psi Air Compressor
37,500 lbs of Pullback
2 Motor Spear Gear Head
Hammer Oiler
2 Piston BEAN Water Injection Pump
Mounted on a CCC (Crane Company Carrier) Truck
Cummins M-11 Diesel Engine
Located : USA
| |
| |
|
Id: WR659
 Ingersoll-Rand TH75W Drill Rig - For Sale
Worldrigs ID: WR659
Model : TH75W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2000
Condition : Used
Description :
2000 Ingersoll-Rand TH75W Drill Rig
55,000 lbs of Pullback (70,000 # cylinder option)
Four Motor High Torque (8,000 Ft.-Lb. Torque) Tophead Drive
IR 1050 cfm / 350 psi Air Compressor (105 Original Hours on Compressor)
Hydraulically Driven 3"x4" centrifugal pump
Cummins QSK-19 Diesel Deck Engine - rated 600 HP
Mounted on a International 5000 Truck
Cummins N14 500 HP Engine
Fuller 8LL Transmission
20K Front Axle / 46K Rear Axles
7 Rod 4-1/2" X 20ft Drill Pipe Carousel
Deck Engine Diesel Fired Pro Heater
16,000 Lb. Main Winch with Swing and Telescoping Jib Boom - the winch is a Gearmatic that
has enough cable capacity to run a three part line (48,000 lbs.).
Newer deck engine installed recently- 2017
New sandline in 2017
360ft of 4 1/2", 2 7/8" thread, 20ft length pipe included
| |
| |
|
|
|
Id: WR81
 Ingersoll-Rand T4W Drill Rig for Sale
Worldrigs ID: WR81 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1980
Condition : Used
Description :
1980 Ingersoll-Rand T4W Drill Rig
IR 900 CFM / 300 PSI Air Compressor
Detroit 12V71 Diesel Deck Engine (Rebuilt less than 500 hours)
50,000 lbs of Pullback
Worm Gear Power Head
Water Injection Pump
Hammer Lubricator
4 & 7 Rod Carousels
Mounted on a CCC (Crane Carrier Company) Truck
CAT 3208 Diesel Engine
Location : USA
| |
| |
|
Id: WR601
 Ingersoll-Rand TH60 Drilling Rig - 1999 Built for Sale
Worldrigs ID: WR601
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1999
Condition : Used
Description :
1999 Ingersoll-Rand TH60 Drill Rig
IR 1050 cfm / 350 psi Air Compressor (needs clutch)
Mission Magnum 3x4 Centrifugal Mud Pump (Hydraulic Driven)
9590 Hours
30,000 lbs of pullback
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a International Paystar 5000 Truck
Diesel Engine
Location : USA
| |
| |
|
|
|
Id: WR541
 Ingersoll-Rand T3W-40K Drill Rig for Sale
Worldrigs ID: WR541 Model : T3W-40K Drill Rig
Manufacturer : Atlas Copco
Year : 2010
Condition : Used
Description :
2010 Ingersoll-Rand T3W-40K Drill Rig (unmounted)
Note: Less than 100 hours on gauge as it was not put to work.
CAT C-15 Diesel Deck Engine @575 HP
IR 1170 cfm / 350 psi Air Compressor
20" Retractable Table
36' Deep Hole Derrick
Dual JIB Control
Standard Wheelbase
Drillstar Rotary Head
40,000 lbs of Pullback
8,000 Ft Pounds 1 speed head (105 rpm)
4.5" x 2-7/8" IF Spindle with 7 Rod Carousel
Max casing size 14"
18,000 lbs Drawworks (bare drum)
48" Jack Cylinder
Char-Lynn Motors
Note: the drill is not mounted on a truck
Location : USA
| |
| |
|
Id: WR102
 Ingersoll-Rand T3W Used Drill Rig for Sale
Worldrigs ID: WR102 Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1987
Condition : Used
Description :
1987 Ingersoll-Rand T3W Drill Rig
S/N: 2713
Cummins 855 Diesel Engine
IR 825 CFM / 350 PSI Air Compressor (Rebuilt 300 Hours Since)
300' ft of used drill pipe (20' x 4-1/2") included
Hammer lubricator
26,500 lbs of pull back
Mounted on a Ford 8000 Truck
Diesel Engine
VIN# 1FDXR82A5HVA24572
8 Speed Transmission
Missing the following main components:
3 Hydraulic Jacks, No top head motors & pulleys, cable pulleys
from main hoist, hydraulic pump missing from the funk box,
no hydraulic cooler, fork wrench, triple pump, gauges, air switch,
regulator, water injection pump, foot valve, cooler leaks and
feed cylinder leaks, etc.
Location : USA
| |
| |
|
|
|
Id: WR528
 Ingersoll-Rand T4W Drill Rig for Sale
Worldrigs ID: WR528 Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used
Description:
1994 Ingersoll-Rand T4W Drill Rig
IR HR2 900-350 (2000 Hours Since Rebuilt)
Cummins KT19 Diesel Deck Engine (Bottom end rebuilt with less than 2000 Hours on it)
50,000 lbs of pull back
Worm Gear head
7x4 rod carousel 4-1/2” x 25’
20 GPM Bean Water injection
7 gallon Hammer lubricator
Winch replace with new one 2016
Mounted on a CCC (Crane Carrier Company) Truck
39,000 Miles
Comes with 375’ ft of Drill Rod (4-½” X 25’ X 2-7/8") & 1- QL-60 hammer. (more used
rods available at an extra cost) & tooling
Sand blasted and painted winter 2015 atlas copco yellow and grey
Notes from the Driller: Rigs comes ready to drill. Drill has veen very well maintained.
Front and back motor have had the bottom end rebuilt
All hydraulic pumps and motors rebuilt recently
Oil changed every 200 hours
Location : USA
| |
| |
|
Id: WR592
 Ingersoll-Rand T4W Drilling Rig For Sale
Worldrigs ID: WR592
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1977
Condition : Used
Description :
1977 Ingersoll-Rand T4W Drill Rig
IR 900 cfm / 350 psi air compressor
CAT 3406 diesel deck engine
Mounted on a CCC (Crane Carrier Company) Truck
CAT 3208 diesel engine
3 in 1 cooler
50,000 of pullback
7 and 4 rod carousels
Location : USA
| |
| |
|
|
|
Id: WR287
 Ingersoll-Rand T3W Drilling Rig for Sale
Worldrigs ID: WR287 Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1993
Condition : Used
Description :
1993 Ingersoll-Rand T3W Drill Rig
CAT 3406 Diesel Deck Engine (Rebuilt)
IR 900 cfm / 350 psi Air Compressor
Top Head Drive & Motors (Rebuilt)
Feed Cylinders (Rebuilt)
Water Injection Pump (Rebuilt)
Mounted on a 1993 Ford L9000 Truck
85,000 Miles
Cummins L10 Diesel Engine
Location : West Africa
| |
| |
|
Id: WR557
 Ingersoll-Rand T3W Drill Rig for Sale
Worldrigs ID: WR557 Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1989
Condition : Used
Description
1989 Ingersoll Rand T3W Drill Rig - S/N: 2900
IR 825 cfm / 350 psi Air Compressor
Caterpillar 3406 diesel deck engine
3636 hours showing on meter (probably turned over & actual
hours might be 13,636)
Sand line winch
Cat water injection pump
Hammer Lubricator
Hydraulic Leveling Jacks
Mounted on a 1989 Ford L8000 Truck
Diesel Engine
74,321 miles
Location : USA
| |
| |
|
|
|
Id: WR270
 Ingersoll-Rand T4W Drilling Rig For Sale
Worldrigs ID: WR270 Description :
Retrofitted in 1990 Ingersoll-Rand T4W Drill Rig - S/N: 11578
IR 900 CFM / 350 PSI Air Compressor (4000+ hours)
Caterpillar 3406C Diesel Deck engine @ 475 HP (Rebuilt in 2011 with 3000+ hours since)
50,000 lbs of Pullback
Worm Gear Power Head with 1 motor
Bean Water Injection Pump @ 12 GPM
Hammer Lubricator F4 Gros
300’ ft of used drill pipe (25' x 4-1/2")
4 & 7 Rod Carrousels
Hydraulic Leveling Jacks
Mounted on a 1990 Kenworth T450 Truck 6x4
CAT Diesel Engine @ 300 HP
Fuller 8L Speed Transmission
Notes on repairs & services:
New hydraulic system installed in 2013, gearbox in 2012, water pump, oil cooler, radiator, head motor, newer paint job since 2012.
Location : N.E. Region
| |
| |
|
Id: WR318
 Ingersoll-Rand TH60 Drill Rig for Sale
Worldrigs ID: WR318 Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Condition : Used
Description :
Ingersoll-Rand TH60 Drill Rig
Note: set up for mud rotary drilling to 1200' foot depths (max 18" opening)
Mounted on a 2004 Kenworth T 800 4 axle Truck
CAT C15 engine (rebuilt 2000 hours ago)
Tridom drive with foll locking differentials
Gardner Denver THE triplex pump (5000 psi piping and surge chamber up to 462 GPM at 720 PSI)
TH60 four motor power head
High pressure swivel
Braden 18000 pound main winch
Sand line / wireline coring winch
Spicer PTO
Sundstrand hydraulic pumps for rotation and mud pump power
2000 hours since full rebuild and remount on newer truck
Location : USA
| |
| |
|
|
|
Id: WR570
 Ingersoll-Rand T3W Drilling Rig For Sale
Worldrigs ID: WR570 Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2002
Condition : Used
Description :
2002 Ingersoll-Rand T3w Drill Rig - S/N: 6707
IR HR2 900 cfm / 350 psi Air Compressor (Rebuilt in 2013 with 200 Hours
Since Rebuild)
CAT 3406 Diesel Deck Engine - Rated 475 Horsepower with 11,800 Original
Hours (New Head Installed in 2011)
7-Rod Carousel For (4-1/2” X 20’) Drill Pipe
4 Newer Hydraulic Motors On Top Head (All Bearings Replaced in Top
Head in 2010)
6-gal. Hammer Oiler
18 GPM Bean Water Injection Pump
Single Rod Loader
Torque Limit Control
18,000 LBS. Main Hoist
2,000 LBS. Utility Hoist
6” Hammer Pocket
4-Leveling Jacks
300' Feet of Drill Pipe Included
Mounted On AN 2002 International Model 2674 Truck W/A CAT C12, 340
Horepower Engine
52,000 Miles On Truck
VIN. #1HTGLAXT22H515312
Regular Maintenance Done Every 200 Hrs.
Location : USA
| |
| |
|
Id: WR107
 Ingersoll-Rand DM45E drill rig for Sale
Worldrigs ID: WR107 Model : DM45E
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used
Description :
1994 Ingersoll-Rand DM45E drill rig
(Almost Completely Rebuilt through 2011)
CAT Diesel Engine
IR 900 cfm / 350 psi Air Compressor
Dry Dust Collector
Carousel handles (30' x 5-1/2") Drill Pipes
Heavy Duty Undercarriage
Location : USA
| |
| |
|
|
|
Id: WR456
 Ingersoll-Rand RD20 II Drill Rig for sale
Worldrigs ID: WR456 Description:
1996 Ingersoll-Rand RD20 Range II Drill Rig
CAT 3406 Diesel Deck Engine
Bean Water Injection Pump
7 Rod Carousel
3 Hydraulic Leveling Jacks
110,000 lbs of Pullback
Mounted on a Central Manufacturing Truck with 4 axles
Cummins L10 Diesel Engine
Note: Bill of Sale only, no title
Note: No Air Compressor on board
| |
| |
or call +65 97768837. 
