Id: WR228
 Versa Drill V - 1040 - DP Drilling Rig for Sale
Worldrigs ID: WR228 Model : V - 1040 - DP Drill Rig
Manufacturer : Versa Drill
Year : 2010
Condition : Used
Description :
2010 Versa Drill V - 1040 - DP Drill Rig
Deck Engine‐ 6238 hours
Air Compressor‐ 4822 hours
Mounted on Peterbilt Truck
11,434 miles
Rods ‐ 400' ft of 3.5 in
Location : USA
|  |
| |
Id: WR317
 Versa-Drill V2000NG Drill Rig For Sale
Worldrigs ID: WR317 Model : V2000NG Drill Rig
Manufacturer : Versa Drill
Year : 2003
Condition : Used
Description
2003 Versa-Drill V2000NG Drill Rig
Note: Unit is missing the top-head (cost extra to replace)
CAT C-15 Diesel Engine @ 490 hp
Ingersoll-Rand 900 cfm / 350 psi air compressor
Mounted on a 2002 Kimble Truck 6x6 (all wheel drive)
205,602 Miles & 6205 Hours on gauge
Hubometer: 599.1
Transmission: 10 speed Eaton
Bean pump
Welder
Location : USA
|  |
| |
|
Id: WR284
 Versa Drill Sonicor 50K Head Drilling Rig for Sale
Worldrigs ID: WR284 Model : Sonicor 50K Head Drill Rig
Manufacturer : Versa Drill
Condition : Used
Description
Versa Drill Sonicor 50K Head Drill Rig
Mounted on a 2002 International 4900 truck
Diesel Engine
285,000 miles
Sonicor 50K Sonic Head (Vibe hours on the head estimated at 1,500 hours)
PTO rebuilt and upgraded in 2015
Brand new hydraulic clamp system
Hydraulic line replacement program, and Electronics and inspection plate panels have been
simplified and upgraded for easier access for repairs and inspections
Location : N.W. Region
|  |
| |
Id: WR234
  Versa Drill V-1040TRX Drill Rig for Sale
Worldrigs ID: WR234 Model : V-1040TRX Drill Rig
Manufacturer : Versa Drill
Year : 2011
Condition : Used
Description:
2011 Versa- Drill V-1040TRX Drill Rig
Deck Engine- 5839 Hours
Compressor- 100 hours, brand new replaced in December 2014
Rods- 400' ft of 3.5 in
Drill Specification
Deck Engine: CAT C-15 (540 HP) A 2,100 w/Dedicated 150 gallon fuel tank, to include fuel cooler.
Combination Compressor Clutch/Pump
Drive Box:
Air compressor clutch engage/disengage (manual) and hydraulic pump gear box.
Hydraulics:
Complete hydraulic system mounted on two(2) hole gear box with integral air compressor clutch
engage/disengage (manual), deck engine fly wheel driven.
Derrick:
10”x16” tubular construction 34’ overall length, 26’ overall head travel and 55,000 lb. rating.
Feed System:
Hydraulic cylinder driven 3” gear track & 4 pinion gears (patented), w/40,000 lb.
pullback 22,100 lb pull down.
Standard
Top Head:
High Performance 3-Speed Top head w/ 2 ½” bore hole:
High Torque 8,100 ft.-lb @ 132 RPM
Mid Torque 6,200 ft.-lb @ 173 RPM
Low Torque 4,280 ft.-lb @ 250 RPM
Control Panel:
Left hand mounted panel with functionally grouped gauges and controls with twin
fold-up platforms.
Leveling Jacks: Four (4) 36” stroke hydraulic leveling jacks with independent controls.
Two (2) mounted behind cab and two mounted at rear of rig.
Centralizer Table:
Swing out rear section and retracting front section with dual cylinder and 10” retract capability.
Carousel:
Hydraulic rotating drill pipe carousel system, set up for fifteen (15) pieces of 3 ½” x 20’ drill pipe.
Drill Pipe Rack:
Hold 15 pieces of drill pipe, includes stabilizer shoot located on the inside of rod box
Main Winch:
Hydraulic winch, 12,000 lb. capacity, bare drum. Includes jib boom w/hydraulic swing and extend.
Auxiliary Winch:
4,000 Auxiliary winch w/ swing jib & additional night light
Air Compressor:
1070 CFM/350 PSI Ingersoll-Rand self contained modular compressors
Water Injection:
Bean 25 GPM Water Injection with foam
Line Oiler: Seven (7) gallon capacity
Extra’s:
1. Hammer Holder (2-6” holders)
2. 18” Aluminum catwalk w/ failing
3. Pro Heat Engine Heater
4. Hydraulic quick disconnects for operating auxiliary/mud pump functions
5. Carousel back loading option w/wired remote pendant
6. Rig will be set up with stand pipe and plumbing for connecting to auxiliary mud pump &
table mounting brackets for mud pit.
7. 200 Gallon fuel tank
8. Helper stand add on & bracket for future pump
Location : USA
|  |
| |
|