Worldrigs ID: WR544

Model: CME-92 Drill Rig
Manufacturer: CME Drill
Condition: Used

Description :

CME-92 Drill Rig
Deck Engine
Mounted on a 5 Ton Chassis Truck
Ford Gas Engine (Model CSG-649P-6006-E)
511,600 km 
3 Hydraulic Leveling Jacks
No Tooling or Hammer will be provided with the unit

Location : USA

Worldrigs ID: WR662
Model : T25K3W Drill Rig
Manufacturer : Driltech
Year : 1994
Condition : Used

Description :

1994 Driltech T25K3W Drill Rig- S/N: 731889
Sullair 840 cfm / 350 psi Air Compressor
CAT 3406 DITA Diesel Deck Engine - rated 430 HP @ 1,800 RPM
30,000 LBS of Pullback
28 ft Head Travel
Pipe Rack Holds For 15 Pipe
(6) Rod Carousel
Rotary Head - rated 89 RPM & 62,600 in LBS. Torque
Jib Boom, Hydraulic Extend With 172 Degree Hydraulic Swing
Hydraulic Winch 7,500 LBS. Capacity
20" Openiing in Table With Hydraulic Adjustment
48" Jaw Type Breakout Wrench
Water Injection Pump is 20 GPM With Foam Pump
DTH Lubricator With 10 Gallon Tank
Fine Feed  & Torque Controls
420 ft. of Used Drill Pipe (4-1/2" O.D. X 20ft) & Basic Tooling Included
Gardner Denver 5 X 6 Air Drive Mud Pump on Board
Hydraulic Leveling Jacks
Mounted on a 1993 Ford LNT8000 - VIN #1FDZW82E0PVA18231
Cummins 8.3l 275 Hp Diesel Engine
10 Speed Transmission
18,000 Front Axle
46,000 Rear Axle

Location : USA

Worldrigs ID: WR859
Description :

1978 Portadrill 524-3A Drill Rig
Gardner-Denver 5-1/2" Mud Pump
Leroi 256 S-2 250 PSI Air Compressor
Hydrostatic drawworks and rotary table
Pipe Slide
Injection pump
Hydraulic leveling jacks
Mounted on a 1999 Ford Louisville truck
Powered by Cummins Red Top N14 Diesel Engine - rated 500 HP
Tag axle

Location : USA

Worldrigs ID: WR810
Model : 1000 Drill Rig & Package
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner-Denver 1000 Drill Rig
14W Drawworks
7-1/2" Rotary Table
Rated for drilling to 1000 ft
Dis-assembled for rebuild
Deck steel replaced in preparation for rebuild
Comes with all components necessary to rebuild back to original specs:
2-stage mast cylinder
3- large 8-1/2 ft outriggers
Piston style WX 1004 compressor (stored inside building)
Gardner-Denver FXG 5x6 mud pump (stored inside building)
24 ft 3-3/8" fluted kelly bar
Little Giant Swivel
Mayhew block for 1000 rig 12" single sheave
292 ft of 3-1/2" flush drill pipe

- 16 ft skid for set up for Gardner Denver 5x8 mud pump, Detroit 353 Diesel
- Engine with Rockford clutch (1600 hours), with 150 gallon fuel tank
- GMC 6-71 Power Unit with Rockford clutch, Rotary table slips, Blue Demon
- Drag Bit 5, spools of cables, assorted bit breakers, 2" relief valve, pipe clamps
and pick up heads, compression coupling and 4" valve, steel mud tank
- 2-3/8" IF to 3-1/2" Reg pipe to bit tubs, pipe spider rings, Rotary Table
- Drill Up slips, shop built collars, T-Pipe for starter, cross over sub adapters, Tool
holder for pipe in table, Petol chain wrenches, regular chain wrenches, Set of
banded v-belts for mud pump skid, 2 rods for GD gear end, bull gear and
eccentric, 2 pairs of sleeves for GD 5x8, valves caps for GD 5x6, cylinder head
for GD 5x6, safe guard and Dodge gear boxes for mud pumps, pinion gear for GD
5x8 duplex 90%, new electric motors 1/2 HP - 3/4 HP - 1 HP stub shaft, power
tower for Keystone Gardner Denver, miscellaneous bits
- 1973 Ford 8000 truck
- Caterpillar 3116 diesel engine
- 10-speedRoadranger transmission

Location : USA

Worldrigs ID: WR882
Description :

1979 Ingersoll-Rand TH60 Drill Rig,
IR 750 CFM / 250 PSI Air Compressor,
Water injection pump,
Toolbox,
Carousel,
4 hydraulic leveling jacks,
Comes with 420ft Drill Pipe 4-1/2" 2-7/8 IF Thread
Mounted on a 1986 GMC General Truck,
Powered 8V92 Detroit Diesel 475 HP,
All drums & brakes good & Tires 80% estimated,

Location : USA

Worldrigs ID: WR330

General Specification

Basic Data :
- Max. hook load : 500 kN                                           
- Mast height : 13,35 m                                                 
- Casing installation height : 8,00 m
- Power swivel working travel : 7,50 m  
               
Dimensions :
- During transport (L/W/H) : approx. 12,90m / 2,50m / 4,00 m                          
- During drilling operation (L/W/H)  : approx. 10,50m / 3,50m / 13,35 m

Operating Conditions :
- Ambient temperature range : -20°C - +45°C
(up to 52°C with special hydraulic oil)

Drilling Depth :
- at drilling diameter 990mm : approx. 250 m*                      
- at drilling diameter 150mm : approx.1.200 m*     
* Drilling depth depending on geology, drilling method
and applied drill string components.

Applicable Drilling Methods :
- Direct Mud Circulation (DC), external mud pump required
- Reverse Mud Circulation (RC) by Air Lift, external compressor required
- Dry drilling / Auger drilling
- DTH Hammer Drilling, external compressor required
- Wire-Line Core Drilling

Special Specification
 
Trailer R1
Type : 3-axle semi-trailer
Dimensions in transport position:
- Lenght (excluding mast) : approx. 10.35m
- Length (with mast) : approx.
- Height : approx. 4.00m
- Width : approx. 2.50m
Type of king pin : 2'' or 3'' ( to be specified)
Height of King pin : approx. 1.35m
Permissible total weight : 45.000 kg
Permissible load of King pin : 18.000 kg
Type of tires : 6 x 385/65 R 22,5 + 1 x spare

Rig frame & Levelling jacks
Description :
Heavy duty steel frame, suitable to mount all rig components,
fixed on the chassis of the carrier

Painting : daffodil yellow (RAL 1007)
Number of levelling jacks : 4
Type of levelling jacks : hydraulically, operated independently
Working stroke :600 mm
Pad size diameter : 500 mm

Deck engine MTU
directly flanged to hydraulic pump distributor gearbox

Manufacturer :  TU (Mercedes)      
Type : V8, water cooled                 
Emission level : EPA/CARB Tier III, EEC 97/68EC 3a 
Capacity : approx. 750 HP at 1.900 rpm           
Electrical system : generator 24 V, 80A
Fuel tank content : 850l

Hydraulic system (Type 2)
Description :
Hydraulic pump distributor gearbox driven by deck engine.
Closed hydraulic circuits for all main components, driven by axial
piston pumps : Power Swivel, Feed device, draw works
(with additional supply pump), Auxiliary hydraulics
(mud pumps, compressor)

Hydraulic oil tank : 1.000l
Type of Hydraulic oil : HVLP 46
(suitable for normal temperature conditions)

Mast RB50 R1
Description :
Constructed of high tensile steel (rectangular tubes),
hydraulically elevated by two (2) double acting hydraulic
cylinder; including: guide rails for power swivel, suspension for
feed device, crown block with sheaves, ladder
for maintenance work.

Total Height in working position : 13.40 m
Operating space (crane block) : 8.80 m
Working stroke (power swivel) :
7.50 m (suitable for drill pipes up to 6.0m length)
Max. load capacity : 500 kN    

Boom for discharge hose
Description :
Mast boom for fastening and securing the discharge
hose for air lift drilling, Attached to the right-hand
side of the mast

Projection : approx. 2,70 m
including : Steel cables for fastening and securing
the discharge hose   

Feed Device
Pull down-force capacity : 80 kN    
Pull back-force capacity :
350 kN (with main hydraulic cylinder)  
500 kN (in conjunction with draw works)

Max. feed speed :
0 - 0,54 m/sec at full load
0 - 1,00 m/sec at max 133 kN

Technical features :
- Load compensation, hydraulically controlled, for
  adjustment of defined Weight On Bit (WOB)
- Controlled WOB, hydraulically controlled,
  constant WOB in dependance of penetration rate
- Vertical compensation, hydraulically controlled,
  allows a defined vertical moving of power swivel
(up/down) per  rotation of spindle (left/right) for gentle
thread make up operation

Power Swivel S150.2
Hydraulical Drive : axial piston pump (variable displacement)
Torque :
- gear 1 : 31.580 Nm at 0 -   45 rpm
- gear 2 : 16.600 Nm at 0 -   85 rpm
- gear 3 :  4.150 Nm at 0 - 340 rpm                  
Max. Mud operating pressure : 40 bar
Inner diameter (free passage) : 150 mm
Connections for :
- heavy duty rotary hose 4" for direct mud circulation
- direct air for DTH Hammer.
- Inlet for 1" air injection pipe (for air reverse circulation
  drilling)

Hydraulic chuck and break device
Description : For making and breaking of drill pipes
Max. pulling force : 500 kN
Max. breaking torque :  48 kNm
Max. Inner diameter (with open clamps) : 195 mm
Max. Outer diameter of drill pipe : 178 mm
Min. Outer diameter of drill pipe : 51 mm

High pressure Inlet for S150, 80 bar : optional (not included)

Hydraulic Clamping Device
Description:
Working Table with hold-back arms swing-mounted at the
mast basis, suitable for interchangeable jaws of different size.

Free passage (closed) : 520 mm
Free passage (open) : 900 mm
Max. clamping diameter : 473 mm (18.5/8'')
Max.clamping force : 500 kN

Make-up and Break-out Device
Description :
Hydraulic cylinder placed on the main frame on the right side,
operated for use with manual tongs, power transfer via chain
system, tongs can be positioned on both sides of the mast for
breaking and tightening the drill pipes, collars and
casing connections.

Pulling force of cylinder : 60 kN
Pulling length of cylinder : 600 mm

Main Winch
Description :
hydraulically driven, suitable for pulling the power swivel or
for installation of casing pipes, operation in combination with
Utility Crane Block 550 kN (triple sheave), overrun safety mechanism

Max. pull-back : 95 kN in first cable layer    
Max. cable speed : 2 m/s
Cable length : 90 m          
Cable diameter : 20 mm  

Auxiliary Winch
Description :
hydraulically driven, with hydraulically released safety brake

Max. pull-back : 25 kN in first cable layer
Cable length : 50 m         
Cable diameter : 10 mm

Wire-Line Coring winch 1.000m
Description : hydraulically driven, with hydraulically released safety brake
Max. pull-back : 25 kN in first cable layer        
Cable length : 1.000 m            
Cable diameter : 8 mm     
 
Features :
- Mechanical holding brake
- Mechanical depth measuring unit with incremental measuring system,
  digital display on the control panel

Mud Line System (standard)
Description :
consisting of horizontal steel pipe system with valves and
connection to the power swivel (vertical pipe and hose)

Diameter : DN 100  / 4"                 
Max. mud pressure : 60 bar steel pipe system / 80 bar mud hoses
External connections : 
4'' (for additional mud pump)
2'' (for external compressor)

Lighting & Electrical system
Voltages : 24V                
Mast lights : 3 x Halogen (70 W)             
Well head light : 1 x Halogen (70 W), movable       
Controll board light : 2 x Halogen (25 W)   
    

Safety system
Description : for quick shut-down of engine and hydraulic
system in case of danger
No. Of emergency shut-off buttons : 2

Operator's platform
Description :
located at the rear left side of the rig with direct sight to the working area,
tiltable, with weather protection tent

Main Control Board
Description : with lockable cover, all gauges and control levers
are labeled by symbols
Main functions :
with electronic pre-control of hydraulic circuits
- Engine start/shut off and speed control
- Engine emergancy alarm
- Manometer of hydraulic circuits
- Power swivel torque
- Power swivel rotation speed
- Hook load indicator
- Pull-up / Pull-down / Weight on bit
- Mud pressure indicator (optional)
- Indicator for pulling force of break-out device  
- Depths indicator for coring winch (optional)                    
- Operating hours (engine, power swivel,...)

Tool box
Description :
Mounted on the drilling rig for basic tools and equipment.
Sufficient for simple maintenance of drilling rig and ancillary equipment.
An additional Tool box will be mounted on the rig and equipped
with additional necessary tools.

Documentation & Certificates
consisting of :
Operation & Maintenance Manual (1x printed / 1x digital) 
Parts books / spare parts list (1x printed / 1x digital)
 
Language : Russian / English
Certificates :

Worldrigs ID: WR668
Model : CF15 Drill Rig
Manufacturer : Failing
Year : 1975
Condition : Used

Description :

1975 Failing CF-15 Drill Rig
Mounted on a 1975 LT-9000 truck
600 ft of (3-1/2, 2-3/8 if) drill pipe
DSM table
bit subbs
drill collars assorted bitts to 12-1/4
100 SDS compressor
FM-45 Failing mud pump
mud pan
desander
lots of tools

Location : USA

Worldrigs ID: WR867
Description :

1980 Ingersoll-Rand TH60 Drill Rig - 0428
Ingersoll-Rand 750 cfm / 250 psi Air Compressor
Bean Triplex Water Injectior Pump
420 ft of (3-1/2" x 20) Drill Pipe
2 Used Hammers & Bits, Slips and Tooling included
10 Rod Carousel
18,000 lbs Winch
Pipe Rack
Hydraulic leveling jacks
Mounted on a 1978 International Harvestor F-5070 Truck
Detroit 8V92 Diesel Engine

Note: Rig is operational but needs a few repairs

Location : USA

Worldrigs ID: WR826
Description :

2006 Simco 2800HT Drill Rig,
Automatic hammer,
Extruder,
Hydraulic clamps (newer),
Gardner Denver 4-1/2x5 mud pump,
Slide base and head tilt,
2 winches,
High Torque head.
New MAST extension 3 pulleys.
Mounted on a Ford F550 Truck,
Diesel Engine,

Location : USA

Worldrigs ID: WR758
Model : T130 Drill Rig - Range III Telescoping Mast
Manufacturer : Schramm
Year : 2004
Condition : Used

Description :

2004 Schramm T130 drill rig - Range III Telescoping Mast - S/N: J130-0110
Substtructure, Rig Floor, Hand Rails, Center Cat Walk
MTU V12-2000TA DDEC Diesel Deck Engine - rated @ 760 HP
Hammer Oilier
130,000 lbs. (59,090 kg) of Pullback
28" inch (711 mm) table opening
50 feet (15.25 m) of clear head travel
3-in ID spindle with optional 5.25-in spindle
Mounted on a CCC (Crane Carrier Company) Truck
VIN# 1CYDGD5874T046284
CAT C12 Diesel Engine - Rated @ 410 HP
Note: New Complete Paint Job finished in May 2013 by EWD with many wells
drilled since
Also available at an extra cost: Dog House, 6000 ft of 4-1/2" IR style drill
pipe, and 1 pipe trailers. (Cost Extra)

Location : USA

Worldrigs ID: WR693
Model : 650 S/S Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic 650 S/S Drill Rig (2)
No Engine currently on deck (but comes with a rebuilt Caterpillar 3406 diesel
engine (heads need torqued down and fuel line needs put back on)
750 CFM / 125 PSI C05 Air Compressor
Bean (FMC) 4-cylinder water injection pump
Dynex main pump & Dynex Head motor
27,500 lb. pullback capability
Gearmatic Hydraulic winch
4-hole Funk Box (hydraulic pump drive)
3 Hydraulic jacks
4 pieces of 25 ft. drill pipe included
Mounted on 1978 CCC (Crane Carrier Company) truck
Powered by Caterpillar 3208 diesel engine,
showing only 4243 miles on odometer
Deck engine and radiator are included but need re-installed
also comes with spare pull down cylinder

Location : USA

Worldrigs ID: WR857
Description :

1973 Gardner Denver 14W Drill Rig
Mounted on a CCC (Crane Carrier Company) Truck
390 ft of Drill Pipe included
Mud Pit & Tee
1000 cfm / 250 psi Air Compressor  
Gardner Denver 5x6 Mud Pump
Bean Water Injection Pump
Cummins 350 Diesel Engine
Foller 13 Speed Transmission
Hour meter reads 1978 Hours
Mileage reads 18,687 Miles
Newer Front tires

Location : USA

Worldrigs ID: WR596
Model : D40K Drill Rig
Manufacturer : Driltech
Year : 1974
Condition : Used

Description :

1974 Driltech D40K Drill Rig
CAT Diesel Deck Engine - rated 425 HP
Sullair 750 cfm / 150 psi air compressor
25’ ft inner & outer Carousels
8000 lb main/jib
Gardner Denver 5x6” Duplex Mud pump (variable hydraulics)
20 GPM water injection pump
Rebuilt hydraulic pumps & splitter
Hot box
good tires
Mounted on a CCC (Crane Carrier Company) Truck
466 diesel engine
Extra: 275’ ft of (25’ x 4-1/2” x 2-7/8 IF Rods)
23’ ft surface collar & mud pit

Location : USA

Worldrigs ID: WR866
Description :

Davey Rouselle M8A Drill Rig
Mounted on a 1991 Sterling truck
CAT 3306 Diesel Engine
8 speed transmission
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Included with 100 ft of Davey rods and a changeover sub to 3.5" API threads for bit

Note: Since 2018 the drill has had the air compressor "gone through", has had
the table replaced, Ramsey pulldown winch replaced, chain cases replaced,
table transmission rebuilt, new radiator for deck engine, and various other
small repairs done
Drill motor is getting weak and will need rebuilt and can be done here if needed
and the price would reflect that
Truck Runs fine but 4th gear does jump out

Location : USA

Worldrigs ID: WR874
Description :

Gardener Denver 15W Drill Rig
Rebuilt and Painted
Truck engine has been rebuilt
Mud pump has also been rebuilt
10” Gardner Denver Retractable table
58ft Mast
Racking board
Bailing drum
new 2” little giant swivel
new 26ft Kelly
hydraulic pull down
air clutches
4 hydraulic leveling jacks

Location : USA

Worldrigs ID: WR883
Description :

1981 Chicago Pneumatic T-700WH Deep Hole Drill Rig & Package
900/350 on-board air,
mounted on a tandem axle steer Kenworth carrier -75,000# pull-back,
4-rod carousel,
CAT 3406B deck engine recently replaced (less than 500 hours ago),
rebuilt dual top-head motors and planetaries,
rebuilt rotational pump and fan motor/pump,
new Nylotron head guides,
new winch line

Additional equipment included :
3,200ft 4 1/2"  x 30ft drill pipe with tandem axle drill pipe trailer
mounted IR tugger winch,
skid mounted Sullair 900/350 air compressor,
skid mounted 2000 gallon fuel tank,
skid mounted 300 bbl water tank,
skid mounted doghouse,
spare CAT 3406B engine (needs rebuilt),
6" hammer, 12" hammer/stabilizer combo,
12" tri-cone stabilizer,
casing lifters for both threaded and plain-end,
casing slips, break out wrench, J-wrench.

Location : USA

Worldrigs ID: WR850
Description :

CME 75 Drill Rig High Torque Fully Refurbished
Refurbished in 2017
Mounted on a 2006 Freightliner M2 truck
Brand new tires and Transmission
Caterpillar engine
Truck has 300,000 actual miles
Brand new hoses
Automatic hammer
Downhole hammer
6 Cylinder Deutz air-cooled engine

Location : USA

Worldrigs ID: WR610
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1989
Condition : Used

Description :

1989 Ingersoll-Rand TH60 Drill Rig
Ingersoll-Rand 825 cfm / 350 psi Air Compressor
Gardiner Denver 5x6 Duplex Power Mud Pump
Pulse Injection Pump 1lt/min - rated 70bar
Cat Water pump 38 lt/min - rated 69 Bar
Gearmatic Winch Model 35 single speed with automatic brake and free-fall attachment 12000 kg @22 metres /min.
Capacity 112 metres of 14mm cable
Weldco Casing Hammer
Pulldown (30,000lbs) 13,610 kg. & Holdback (30,000lbs) 13,000kg
Rotation torque (60,000 in-lb) 692 kg-m & Rotation speed 0-100 rpm
Mounted on a Hendrickson Truck (8x6) 6 wheel drive
Detroit 8V92TA V8 Diesel Engine - rated 427 hp
400' ft of drill pipe & tooling & spare parts are included

Location : Western Region, Europe

Worldrigs ID: WR844
Description :

1994 Ingersoll-Rand T4W Drill Rig
Rebuilt 2006
Rebuilt Cummins KTA19C Diesel Deck Engine (rated 600 HP at 2100 RPM)
Rebuilt in 2006 a IRH2.5 1070 cfm / 350 psi air compressor
Mounted on a CCC (Crane Carrier)
Cummins L10 diesel engine
50,000 lbs of pullback
Setup for 2-7/8" IF Drill Pipe

The following work was performed when rebuilt:
Rebuild of rig and components
Remanufactured Cummins engine KTA19C 600 HP @ 2100 RPM from Cummins
(upgraded from original 545 HP @ 2100 RPM)
Remanufactured IR compressor HR2.5 1070 CFM @ 350 PSI
Rebuilt funk box Rebuilt or new hydraulic pumps and motor
Rebuilt hydraulic cylinder All new hydraulics and air hose
New and upgraded radiator
New and upgraded air compressor, oil cooler and hydraulic oil cooler
Valve spool rebuilt – new seals and control handles
New feed chains upper and lower – Upgraded
New front leaf springs on carrier
New gauges
New wire harness
Rig and all parts sandblasted and painted grey and red
Rig completely serviced – Ready to drill

Additional tooling :
6” IR QL60 Drive Hammer with Bit
6” IR QL60 Drill Hammer with 4-1/2” x 21.5ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 20ft lead steel with bit
4-1/2” X 25ft 2-7/8 API Drill Rod (11 pieces)
6” Casing Drive Plate
8” Casing Drive Plate
10” Casing Drive Plate
1 - Petol Chain Wrench set up for 4-1/2” Drill Rod and 6” Hammer
1 – Petol Chain Wrench set up for 6” Drill Rod and 8” Hammer
Lincoln Welder with Leads
Oxy/Acetalene Torch Setup

Location : Eastern Region

Worldrigs ID: WR840
Description :

Davey Rotary Table Drill Rig
200 PSI Piston Air Compressor
Detroit diesel deck engine
270 gas engine in truck (has a bad valve in it)

Location : USA

Worldrigs ID: WR805

SOLD

Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2004
Condition : Used

Description :

2004 Ingersoll-Rand T3W Drill Rig
Engine Hours: 20,621
50 ft – 45,000lb static hook load capacity
hydraulic raise/lower mast
Atlas Topco top drive
Braden 23,000 lb winch
mud system (5” x 6” or 5.5” x 8” GD mud pump)
hydraulic set up to run two pumps or air compressor
hydraulic hoses are re-conditioned
rig derrick can be shortened if requested

Note: no deck engine or air compressor on board the drill
Mounted on International 5600i Truck
Cummins ISX 14.9L Engine
475 Adv horsepower
engine brake
Eaton Fuller 18 speed manual transmission
330” wheel base
8 X 6 20,000lb front axle
54,000lb rears

Location : North America

 

Worldrigs ID: WR690
Model : T130XD Drill Rig
Manufacturer : Schramm
Year : 2012
Condition : Used

Description :

2012 Schramm Rotadrill T130XD Drill Rig
Fluid Line Plumbing, Welded
Rotation Guard
Telemast 50 ft
Helpers Platform, Mast Mounted
Mini Lube System
Pullback Limiter
Rotationlock for DH Mtr, w/FS
Slow Feed Drill-Up Valve
Tophead High Cap 4 Meter 4" Tilt
Four Meters, 15/30 cu in
Split Table Assembly, No Slips
Adj Height Brkout Wrnch Mount
Variable Spd Fan (No Comp)
Heater, Diesel Fired Coolant
Spark Arrestor
Note: No Air Compressor on board
Auxiliary Tooling Compressor
Tool Lubricator, Piston Pump
Mounted on a CCC (Crane Carrier) Truck 10x6 ULSD
Aluminum Wheels 10
Heater, Diesel Fired Coolant
ProHeat style Heater for Crane Carrier motor
Pro Heat# PH0403
Jib Boom, Hydraulic Range 2
Hydraulic Pipe Racks, Set (2)
LoadSafe Handler Hydraulic Supply
LoadSafe Pipe Handler
Power Breakout
Remote Hydraulics Supply
Winch, 9,600 lb (150 ft x 1 /2")
Winch, Survey Line

Location : Western Region

Worldrigs ID: WR870
Description :

Failing Holemaster 1000 Drill Rig
Mounted on a 1974 Mack truck
V8 Mack engine
new 2" Little Giant swivel
23ft kelly
5-1/4" rotary table
256 LeRoi air compressor
Gardner Denver 5x6 piston pump
2 hydraulic leveling jacks

Location : USA

Worldrigs ID: WR886
Description :

2012 Schramm TXD 200 Drill Rig
serial number J135-0216, trailer VIN#: 1K9AD40C1C3268138.
Detroit DDC/MTU 12V-2000 Diesel Deck Engine

Tilt Top Head Drive:
Heavy duty, single reduction gearbox with 4 two-speed disc valve type 
hydraulic motors
Variable rotation speed via HRC control
Torque: 0-90 RPM @ 17,750 ft-lbs (24,066 N-m)
0-180 RPM @ 7,670 ft-lbs (10,399 N-m)
Rotation Speed: 0 - 180 RPM · 

Feed System:
50 ft (15.24 M) head travel
200,000 lbf (890 kN) hoist capacity
100 fpm (30.5 m/min) hoist speed
32,000 lbf (142 kN) pulldown
200 fpm (61 m/min) pulldown speed

Drill Table:
Table Opening : 30" inches (768 mm) diameter with table retracted
Hydraulically retractable slip box

Drill Pipe And Casing:
Range III tubular 30 inch capability

Winch:
Planetary design with spring applied hydraulic release brake
9,600 lbf (42.7 kN) bare drum line pull
150 fpm (46 m/min) bare drum line speed
Hydraulic jib boom swing and extend
Auxiliary winch available
The drills have low wear on the cables, bearing and pivot points as well 
as the Control panel
All are in excellent/very good condition during last inspection
LoadSafe pipe handling systems (hands free pipe loading system)
mounted on Trailers

Package available  each of the following:
Generator House with 2 Maraathon Model 431CSL6202-B211 60 HZ Phase 1 
120/240V 122 KW 504 AMO or 3 Phase 277/480 155 KW 233 AMP poered by 
Perkins 6.6 L 1106 IR 2340 Shop air ,Hyd lift with Honda GX392,4000 Gallon 
feul tank and 4 lights on roof.
Weatherford T425 Triplex Mud pump powered by John Deere 6135 diesel engine 
(Tier IV) - rated 500 HP, 6.50 Plunger 900 PSI, MCM 4x5x14 Super Charge 
Centrifugal pump with soap mixing tanks in back
750 BBL Water tank with hydraulic lift dog house
Crew changing house
Crew House 
8000 ft of drill pipe (4" DP New 30ft 6" NC40)
(4) 6-1/2” Drill collars
Every unit is clean & straight and it is a very nice package in excellent/very 
good condition after inspections in 2020

Location : USA

Worldrigs ID: WR331

Description :
 

The RB 15 enables the user to drill with the following methods, with borehole
diameters 4” (108 mm) to 24” (609 mm):
 

Rotary-drilling with direct circulation
Rotary-drilling with reverse circulation Auger-drilling
 

Percussion core drilling (ram coring)
Wire-line core drilling 
Down-The-Hole hammer drilling (direct / reverse)
Free-fall drilling
Geothermal Drilling with DoubleRotation-Head
Inclined Drilling max.45 degrees
 

Additional rig components
Addit. to specifications overleaf
Foam pumpe
Line oiler (for DTH)
Free-fall winch
Hose winch
Percussion drilling device
Hydraulically driven Gen-set
Hydraulically driven welding-set
Rod handling arm
Rod box
 

Base carrier : Crawler base
 

Crawler width / Track shoe width : 2.450 / 500 mm
Transport dimensions L / W / H Diesel Engine (water-cooled) : 10.000 / 2.540 / 3.200 mm
Exhaust Emission Standard : EPA / Carb Tier 3, EU Stufe 3A
Rated output : 205 kW @ 2.200 U/min (rpm)
Diesel tank capacity : 280 l
Feed device (hydr. cylinder)
Push-down / Pull-back force : 70 / 140 kN
Feed speed : 0 - 0,8 m/s
 

Power swivel : L130
Gear select, 3 speeds
Torque at 0 - 34   rpm : 11.750 Nm
Torque at 0 - 100 rpm : 4.150 Nm
Torque at 0 - 320 rpm : 1.200 Nm
 

Chuck & break device : HSB 178.300
Clamping diameter max. / min. : 170 / 51 mm
Max. breaking torque : 41.000 Nm
 

Outrigger cylinder
Max. stroke : 600 mm
 

Mast head with hydr. swing-out device
Swing-out displacement : 700 mm
Swing-out force : 8 kN
 

Clamping device
Max. clearance diameter : 400 mm
Max. casing nominal diameter : DN 255
Max. clamping force : 300 kN

Winches
Main winch
Line pull 1st layer : 95 kN
Wire rope diameter / rope length : 20 / 130 m
Coring winch
Line pull 1st layer : 20 kN
Wire rope diameter / rope length : 8 / 300 m
Auxiliary / percussion winch
Line pull 1st layer : 26 kN
Wire rope diameter / rope length : 10 / 49 m

Pumps
Triplex piston pump
Discharge / Operating pressure : 270 l/min / 40 bar
Duplex piston pump
Discharge / Operating pressure : 450 l/min / 20 bar
Eccentric screw pump
Discharge / Operating pressure : 350 l/min / 24 bar
Centrifugal pump
Discharge capacity / Op.pressure : 1.500 l/min / 8 bar
Suction pump
Discharge capacity / Suction height : 5.300 l/min

Screw type compressor Compressor
Discharge / Operating pressure : 7 m³/min / 15 bar
Rotating casing table : VDT 324  VDT 419

Torque : 13 / 20 kNm  30 / 45 kNm

Worldrigs ID: WR833
Description :

2011 Atlas Copco RD20 Range III Drill Rig
Cummins KTAA19 (2019 Model) Diesel Deck Engine 800 Hours
IR HR2.5 1250 cfm / 350 psi Air Compressor
Mounted on CCC (Crane Carrier Company) Truck
Diesel Engine
Currently Working

Location : Middle East Region

Worldrigs ID: WR867
Description :

1980 Ingersoll-Rand TH60 Drill Rig - 0428
Ingersoll-Rand 750 cfm / 250 psi Air Compressor
Bean Triplex Water Injectior Pump
420 ft of (3-1/2" x 20) Drill Pipe
2 Used Hammers & Bits, Slips and Tooling included
10 Rod Carousel
18,000 lbs Winch
Pipe Rack
Hydraulic leveling jacks
Mounted on a 1978 International Harvestor F-5070 Truck
Detroit 8V92 Diesel Engine

Note: Rig is operational but needs a few repairs

Location : USA

Worldrigs ID: WR682
Model : CME-75 Drill Rig
Manufacturer : CME Drill
Year : 1988
Condition : Used

Description :

1988 CME-75 Drill Rig
Mounted on a newer 1998 Ford 6X4 FT900 Truck
94,866 miles
3 axles
Ford 300 6 cylinder
Gardner Denver 4.5" x 5" FF FXFM Mud Pump,
2 hydraulic Hoists
wireline & cathead
high torque rotary drive
quick disconnect mast
in-out & sideways slide base
140 lb. auto SPT hammer 
3 hydraulic Jacks
hydraulic Auger rack
500 gallon water tank
three locking tool boxes
locking storage under water tank and rig
Re-diamond plated rig body Feb. 2010 (garage keep since)

Location : USA

Worldrigs ID: WR800
Model : 1500 Drill Rig
Manufacturer : Midway
Condition : Used

Description :

Midway 1500 Drill Rig
10" table retracts but needs cylinder
5-1/2 x 8 GD Pump
New transfer case
4 jacks
Long Derrick
Long Kelly
500 of 2-7/8" drill pipe
Auto car
Caterpillar 3406 Diesel Engine
Bill of sale only

Location : USA

Worldrigs ID: WR598
Model : T130XD Drill Rig - Tilt Power Head
Manufacturer : Schramm
Year : 2007
Condition : Used

Description :

2007 Schramm T130XD Drill Rig
Detroit DDC/MTU V12-2000TA DDEC Diesel Deck Engine
18,500 Hours
Top Head: Tilt head - two hydraulic motors. 0-143 RPM with 106,600 in-lb of torque
50' feet (15.25 m) of clear head travel
Range III casing
130,000 lbs of Pullback
Free standing design with 28" table opening
Hydraulic pumps
Proheat engine heater
Hydraulic stabilizers
Mounted on a CCC (Crane Carrier Corp) 10X4X4 Truck
Caterpillar C13 ACERT Diesel Engine
Eaton Fuller 8LL Transmission
Air Lift 3rd axle

Location : USA

Worldrigs ID: WR538

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on Ford truck - VIN T91KVR58157
Engine
Note: No Air Compressor on board (cost extra to install)

Location : USA

Worldrigs ID: WR492
Speedstar S S61A Cable Tool Rig Details:

Worldrigs ID: WR780
Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago Pneumatic T650 Drill Rig
mounted on an IH Truck
All original parts
Head need work
Good Parts Machine

Location : USA

Worldrigs ID: WR103

1995 Foremost Barber DR12/36 drill rig
Sullair 1150 CFM / 350 PSI Air Compressor

Worldrigs ID: WR146
Model : GXXTA D/D Back-In Well Service Rig
Manufacturer : Hopper
Condition : Used

Description :

Hopper GXXTA D/D Back-In Well Service Rig - S/N: 191
Detroit Series 60 Diesel Engine
Allison 5860 Transmission
15” Double Hydro Brake
Pemco 96’ ft H 180,000 lbs Mast
Hydraulic Raised & Scoped
Rod & Tubing Boards
Mounted on a CCC (Crane Carrier Company) 5-Axle Truck
Leveling Jacks
385/65R22.5 Front & 11R24.5 Rear Tires
Disc Wheels
Sold by "Bill of Sale" only
 

Location : USA
 

Worldrigs ID: WR797
Model : TXD Drill Rig & Package
Manufacturer : Schramm
Year : 2012
Condition : Used

Description :

2012 Schramm TXD Drill Rig Package
Deck Engine : Detroit Diesel DDC/MTU 12V-2000

Tilting Top Head Drive : Heavy duty, single reduction gearbox
with 4 two-speed disc valve type hydraulic motors  
variable rotation speed via HRC control
Torque: 0-90 RPM @ 17,750 ft-lbs (24,066 N-m)
0-180 RPM @ 7,670 ft-lbs (10,399 N-m)
Rotation Speed: 0 - 180 RPM  

Feed System : 50 ft (15.24 M) head travel  
200,000 lbf (890 kN) hoist capacity  
100 fpm (30.5 m/min) hoist speed  
32,000 lbf (142 kN) pulldown  
200 fpm (61 m/min) pulldown speed

Drill Table : Table Opening: 30 inches (768 mm) diameter with table retracted  
Hydraulically retractable slip box

Drill Pipe and Casing : Range III tubular capability  
30 inch

Winch : Planetary design with spring applied hydraulic release brake ·
9,600 lbf (42.7 kN) bare drum line pull  
150 fpm (46 m/min) bare drum line speed  
Hydraulic jib boom swing and extend  
Auxiliary winch available

This drill has low wear, Cables and bearing and pivot points,
Control panel all are in excellent condition.
Hoses are getting older.
Mounted on a Trailer
LoadSafe pipe handling systems
Generator house 2 155KW Generators powered by Perkins IR Shop Air,
Hydraulic lift jacks and 3 stage closing unit.
500 HP Mud pump Weatherford T425 powered by John Deere 61356.50 Plunger 900 PSI,
MCM 4x5x14 Super Charge pump with soap mixing tanks in back
750 BBL Water tank with hydraulic lift dog house
Crew changing house
Crew House
8000 ft  of drill pipe
4 - 6-1/2” Drill collars
Every pcs is clean and straight nice package.

Location : USA

Worldrigs ID: WR862
Description :

2011 Schramm RC685 Exploration Drill Rig
MTU V2000 Diesel Deck Engine
Sullair 1350 cfm / 500 psi Air Compressor
Hours : 12,317
Miles : 7,129
Boart Longyear Rod Handler
Hydraulic Pumps
Collector Box & Cyclone
Drill Table Opening : 22 inch
Rod Spinner & hydraulic breakout wrenches
Rated Depth Capacity : 5-1/2" diameter hole to 2,300 feet deep
Rated Pullback : 94,000 lbs
CAT Walk
Hydraulic Leveling Jacks
Mounted on a 2012 International Truck
MaxxForce Diesel Engine
Misc Drill Tooling for an extra cost (in pictures) Stablizer,
Hole Opener, Collar, Land Plates

Note: Set up for RC (Reverse Circulation) minerial exploration & mining.
This is not a T685 model for water wells

Location : USA

Worldrigs ID: WR883
Description :

1981 Chicago Pneumatic T-700WH Deep Hole Drill Rig & Package
900/350 on-board air,
mounted on a tandem axle steer Kenworth carrier -75,000# pull-back,
4-rod carousel,
CAT 3406B deck engine recently replaced (less than 500 hours ago),
rebuilt dual top-head motors and planetaries,
rebuilt rotational pump and fan motor/pump,
new Nylotron head guides,
new winch line

Additional equipment included :
3,200ft 4 1/2"  x 30ft drill pipe with tandem axle drill pipe trailer
mounted IR tugger winch,
skid mounted Sullair 900/350 air compressor,
skid mounted 2000 gallon fuel tank,
skid mounted 300 bbl water tank,
skid mounted doghouse,
spare CAT 3406B engine (needs rebuilt),
6" hammer, 12" hammer/stabilizer combo,
12" tri-cone stabilizer,
casing lifters for both threaded and plain-end,
casing slips, break out wrench, J-wrench.

Location : USA

Worldrigs ID: WR782
Manufacturer : Speedstar
Condition : As-Is

Description :

Speedstar Quick Drill Rig
Note: only good for Parts
Condition: As-Is
Mounted on Ford Truck

Location : USA

Worldrigs ID: WR844
Description :

1994 Ingersoll-Rand T4W Drill Rig
Rebuilt 2006
Rebuilt Cummins KTA19C Diesel Deck Engine (rated 600 HP at 2100 RPM)
Rebuilt in 2006 a IRH2.5 1070 cfm / 350 psi air compressor
Mounted on a CCC (Crane Carrier)
Cummins L10 diesel engine
50,000 lbs of pullback
Setup for 2-7/8" IF Drill Pipe

The following work was performed when rebuilt:
Rebuild of rig and components
Remanufactured Cummins engine KTA19C 600 HP @ 2100 RPM from Cummins
(upgraded from original 545 HP @ 2100 RPM)
Remanufactured IR compressor HR2.5 1070 CFM @ 350 PSI
Rebuilt funk box Rebuilt or new hydraulic pumps and motor
Rebuilt hydraulic cylinder All new hydraulics and air hose
New and upgraded radiator
New and upgraded air compressor, oil cooler and hydraulic oil cooler
Valve spool rebuilt – new seals and control handles
New feed chains upper and lower – Upgraded
New front leaf springs on carrier
New gauges
New wire harness
Rig and all parts sandblasted and painted grey and red
Rig completely serviced – Ready to drill

Additional tooling :
6” IR QL60 Drive Hammer with Bit
6” IR QL60 Drill Hammer with 4-1/2” x 21.5ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 20ft lead steel with bit
4-1/2” X 25ft 2-7/8 API Drill Rod (11 pieces)
6” Casing Drive Plate
8” Casing Drive Plate
10” Casing Drive Plate
1 - Petol Chain Wrench set up for 4-1/2” Drill Rod and 6” Hammer
1 – Petol Chain Wrench set up for 6” Drill Rod and 8” Hammer
Lincoln Welder with Leads
Oxy/Acetalene Torch Setup

Location : Eastern Region

Worldrigs ID: WR826
Description :

2006 Simco 2800HT Drill Rig,
Automatic hammer,
Extruder,
Hydraulic clamps (newer),
Gardner Denver 4-1/2x5 mud pump,
Slide base and head tilt,
2 winches,
High Torque head.
New MAST extension 3 pulleys.
Mounted on a Ford F550 Truck,
Diesel Engine,

Location : USA

Worldrigs ID: WR806
Model : 1000 Drill Rig
Manufacturer : Failing
Condition : Used

Description :

Failing 1000 Water Well Drill Rig
5-1/2" Rotary Table
(2) Leroi Air Compressors (low pressure)
5 X 6 Duplex Mud Pump (with Gardner Denver and Failing Parts installed)
Pipe Rack
Mounted on a 1969 Diamond Rio Truck - VIN #DRE64HC576224
Detroit 8V71 Diesel Engine - rated 318 HP
20 Drill Pipe (2-7/8" OD X 20 x 2-3/8" IF Threads)
(2) Shorter Length Drill Pipe and a Stabilizer

Location : USA

Worldrigs ID: WR766
Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used

Description :

Simco 2800 Auger / Rotary Drill Rig
Combo auger/rotary
Mounted on 2000 Chevy W4500
Duetz diesel deck engine
25 HP kohler mud pump engine
Mud pump is a 2X3 centrifugal
170 feet of drill rod with 2 roller cone bits
Drill rod is 2-7/8 OD
10 ft extension to the derrick that allows you to work with 20 ft
lengths of pipe
Break out wrench and air compressor on the truck
Truck is a 5 speed cab over
Truck has 135239k and is 2 wheel drive 4 cyl Isuzu diesel
IMT HYD 25CFM @100PSI Air Compressor (?)
Simco thread and set up to run 10 foot lengths

Location : USA

Worldrigs ID: WR685
Model : B56 Drill Rig
Manufacturer : Mobile
Year : 1970
Condition : Used

Description :

1970 Mobile B56 Drill Rig
Diesel Engine on deck
3L6 Moyno water pump
Cathead
Mounted on 1993 International truck
p/b diesel engine

Location : USA

Worldrigs ID: WR866
Description :

Davey Rouselle M8A Drill Rig
Mounted on a 1991 Sterling truck
CAT 3306 Diesel Engine
8 speed transmission
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Included with 100 ft of Davey rods and a changeover sub to 3.5" API threads for bit

Note: Since 2018 the drill has had the air compressor "gone through", has had
the table replaced, Ramsey pulldown winch replaced, chain cases replaced,
table transmission rebuilt, new radiator for deck engine, and various other
small repairs done
Drill motor is getting weak and will need rebuilt and can be done here if needed
and the price would reflect that
Truck Runs fine but 4th gear does jump out

Location : USA

Worldrigs ID: WR856
Description :

1992 Ingersoll-Rand T2W Drilling Rig & Package
T2W Drill Outfitted a follows:
IR 900 CFM / 350 PSI Air Compressor
Moyno centrifugal mud pump
500ft of drill pipe on truck (2-7/8” IF), 8-1/2 button bit with stabilizer,
5” hammer, crossover subs included
Mud pan
Mounted on Volvo truck
Cummins N14 diesel engine

Package Includes :
1994 Peterbilt water truck
Grout mixer
2000 gallon in-bed water tank
Auxiliary fuel tank behind cab

Location : USA

Worldrigs ID: WR627
Model : T450 Drill Rig
Manufacturer : Schramm
Year : 2008
Condition : Used

Description :

2008 Schramm T450 Drill Rig
CAT 3406 Diesel Deck Engine
Sullair 900 cfm / 350 psi Air Compressor - rated 1800 RPM (6000+ hours)
8500+ Frame Hours
Top head power drive: 2 hydraulic motors   
Torque (slow) 106 - 610 lbs & Torque (fast) 53 - 306 lbs   
Pull Back is 30,000 lbs
Cat 10/10 Water Injection Pump
Hammer Lubricator
400 ft of (4-1/2inches x 20ft x 3-1/2inches) Drill Pipe
2008 International Truck
Maxforce 300 HP Diesel Engine    
Transmission Fuller 8 speeds  
 
Location : NE Region

Worldrigs ID: WR771
Model : HTB3KDD Drill Rig
Manufacturer : Howard Turner
Year : 2008
Condition : Used

Description :

2008 Howard Turner HTB3KDD Drill Rig Package
CAT C-7 Diesel Engine - rated 260 BHP
6 Cylinder Diesel 2000 MOD NEW
ALLISON-GM MOD # 653
Drawworks :
H.T.B. CANTON TX.
MOD # HTB5KDD - MUSTANG
Clutches - PO3-10
Twin Disk Brakes - 8 x 28 2 per drum
Drums - 14"
Drums - lea bus for 3/4" cable
Drum Drive - 350 hp deran r-angel
25,000 single line pull to 40,000 lbs
Double 120 Chain
Mast : 62ft X 6ft X 3ft HTB - 150,000 #
Carrier : 50ft tandem axle
Swivel : 72 Ton - 144,000 Pounds
JIB Winch
Hydraulics : 20 gpm, 2000 psi. | PTO Driven from Allison Transmission
Drilling Depth : 6,000 feet
Hours : 3087

Extra Item Available(for extra cost) :
2000 Mud Cleaning System FXZ Gardner Denver mud pump
Mounted on a TRA 48ft Trailer 2000 Olympian 60 kW Generator (8,376 Hours)
1990 Ford 9000 - Equipped with winch for loading pipes
Trailer designed for loading pipes with HTB Drilling Rig sold with
2000ft pipes (5” Drill pipe whith 3.5 IF con/ 13.30 lbs)
Tiger 500 Gallon Fuel Tank
Drill colars 6′′ x 28ft ( 2pcs)
3 1⁄2" bottel neck elevators
Pipe Elevators
Drag bit
Tricone bit
Rods 3-1/2′′ x 30ft
Trush Pump
Casing Elevator
Bit 26"
Sub-base

Location : USA

Worldrigs ID: WR869
Description :

1972 Chicago Pneumatic 650 Drill Rig
Sullair 750/250 air compressor (verifying the size & model)
Caterpillar 3306 Diesel Deck Engine
Gardner Denver 5x6 air driven mud pump
Hydraulic slide pipe rack
Winch
Mounted on a Ford 900 Truck (VIN #: T91KVN93939)
Caterpillar 3208 Diesel Engine
Bobcat welder

Location : USA

Worldrigs ID: WR629
Model : T985 Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T985 Drill Rig
Dual 425 CFM / 250 PSI Air Compressors
Dual Detroit Diesel Engines
Mounted on a twin axle CCC Truck
Diesel Engine
Working Order

Location : USA

Worldrigs ID: WR454

Model : RD20 II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1993
Condition : Used

Description

1993 Ingersoll-Rand RD20 Range II Drill Rig - S/N: 3987
Cummins KTA19 Diesel Deck Deck Engine @ 600 HP
7 Rod Carusel
Cat 2520 water injection pump
Hammer Lubricator
Hydraulic Leveling Jacks
Mounted on a 1993 Central Manufacturing Truck with 4 axles
Cummins L10 Diesel Engine
VIN number: PGV84002
Note: No Air Compressor on board as of now (was a IR 1050/350)

Location : USA

Worldrigs ID: WR350

Model No : V-2000NG Drill Rig
Manufacturer : Versa Drill
Model Year : 2004
Condition : Used

Description :

2004 Vera Drill V-2000NG Drill Rig
Mounted On A 2003 Kimble Model C3300 6x6 Carrier Truck
Eaton 10 Speed Transmission
5,000 Hours
Fabco 23,000 Lb Front Axle
Spincer 46,000 Lb Rear Axles With Different Lock Out
3-Stage Jake Brake
250 Gallon Aluminum Fuel Tank
Aluminum Wheels
Aluminum Cab
Aluminum Diamond Plate Fenders
Cat C-16 600hp Diesel Engine
Ingersoll-Rand 1070cfm/350psi Air Compressor
80,000lb Pull Back/34,000lb Pull Down
3-Speed Top Head Drive
18,000 Lb Hydraulic Main Winch With Jib
2,000 Lb Auxiliary Winch With Jib
Automated Pipe Storage And Controlsystem
New Batteries
Good Rubber
All Wheel Drive
500' Of 2 7/8 X 4 1/2" Drill Pipe

Location : USA

Worldrigs ID: WR603
Model : 3000 Drill Rig
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner Denver 3000 Trailer Mounted Drill Rig
Set up for RC
Brewster 18" removable Table
Single draw works
7 Part Main block
2 Cat heads
New Hydraulic pump system
New Hydraulic winch for Tail out
International DT466 Diesel engine
Trailer mounted
6 Leveling jacks
Hydraulic tower ram
Dog House-- Optional at extra cost
The rig is 12’ 6” tall when connected to a day cab tractor. The width is 8’

Location : USA

Worldrigs ID: WR662
Model : T25K3W Drill Rig
Manufacturer : Driltech
Year : 1994
Condition : Used

Description :

1994 Driltech T25K3W Drill Rig- S/N: 731889
Sullair 840 cfm / 350 psi Air Compressor
CAT 3406 DITA Diesel Deck Engine - rated 430 HP @ 1,800 RPM
30,000 LBS of Pullback
28 ft Head Travel
Pipe Rack Holds For 15 Pipe
(6) Rod Carousel
Rotary Head - rated 89 RPM & 62,600 in LBS. Torque
Jib Boom, Hydraulic Extend With 172 Degree Hydraulic Swing
Hydraulic Winch 7,500 LBS. Capacity
20" Openiing in Table With Hydraulic Adjustment
48" Jaw Type Breakout Wrench
Water Injection Pump is 20 GPM With Foam Pump
DTH Lubricator With 10 Gallon Tank
Fine Feed  & Torque Controls
420 ft. of Used Drill Pipe (4-1/2" O.D. X 20ft) & Basic Tooling Included
Gardner Denver 5 X 6 Air Drive Mud Pump on Board
Hydraulic Leveling Jacks
Mounted on a 1993 Ford LNT8000 - VIN #1FDZW82E0PVA18231
Cummins 8.3l 275 Hp Diesel Engine
10 Speed Transmission
18,000 Front Axle
46,000 Rear Axle

Location : USA