Worldrigs ID: WR693
Model : 650 S/S Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic 650 S/S Drill Rig (2)
No Engine currently on deck (but comes with a rebuilt Caterpillar 3406 diesel
engine (heads need torqued down and fuel line needs put back on)
750 CFM / 125 PSI C05 Air Compressor
Bean (FMC) 4-cylinder water injection pump
Dynex main pump & Dynex Head motor
27,500 lb. pullback capability
Gearmatic Hydraulic winch
4-hole Funk Box (hydraulic pump drive)
3 Hydraulic jacks
4 pieces of 25 ft. drill pipe included
Mounted on 1978 CCC (Crane Carrier Company) truck
Powered by Caterpillar 3208 diesel engine,
showing only 4243 miles on odometer
Deck engine and radiator are included but need re-installed
also comes with spare pull down cylinder

Location : USA

Worldrigs ID: WR214

Model: 650 Drill Rig
Manufacturer: Chicago Pneumatic
Year: 1986
Condition: Used

Description :

1986 Chicago-Pneumatic 650 Drill Rig
GHH 825 cfm / 350 psi Air Compressor
CAT 3406 diesel deck engine
Mounted on Ford truck
diesel engine
Around 1,000 ft of near new drill pipe at extra cost

Location : USA

Worldrigs ID: WR784
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2000
Condition : Used

Description :

2000 Ingersoll-Rand TH60 Drill Rig
Included with Angle Drill Package, 30 degree to 90 degrees
Run by Motor Via Spicer 792 Splitter Box
Hydraulics And Compressor Selectively Controlled
Compressor: 700/350   HR2 Ingersoll-Rand Brand New 3 Years Ago
Winch Braden C230B
Hydraulics – 18 Ton
Sandline Ramsey 4000# Dual Drum Hydraulic
Auxiliary Hydraulic Outlet To Run Off Board Equipment (Ie. Mud Pump,
Casing Jacks And Pipe Feeder)
Led Lights
Derrick Controlled Floor
Pipe Slide And Storage Rack Holds 24 Joints Of 3-1/2" Drill Pipe
Pipe Carousel Holds Nine Joints
Power Invertor :  Can Run Power Tools
New Brake Pads 2019
Complete Over Haul Of Unit May And June Of 2012...Finished With New Paint
Engineer Inspected To Back To Manufactures Specifications
Angle Package, Can Drill All Angles From 30-90 Degrees
1-Air Hammer Included For Hard Rock Drilling
Down Hole Lube Inspector
Manual For Rig 2 Is Equipped To Run Mud Pumps But Not Included
Mounted On a 2000 International Paystar 5000 Truck – (Motor Checked 2012
And Heads Done)
Cummins N14 Plus Diesel Engine
46,000 LD Rears By 2 Rebuilt 2019 By Mechanics

Location : USA

Worldrigs ID: WR145

Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used
Year : 1989

Description :
 
1989 Simco 2800 Drill Rig
Mounted on a 1989 F600 Truck with Diesel Engine
20' stroke in the tower (10000 lbs of thrust & 4000 lbs rotation)
Mission 2x3 mud pump
Sullair compressor
200' ft of simco pdg drill pipe
Mud Pan attached to the truck
 

Location : USA

Worldrigs ID: WR456

Worldrigs ID: WR411

 

Description:

 

 

 

Worldrigs ID: WR877
Description :

2015 Atlas Copco Pit Viper 235 Drill
Pressure: 350 psi
Flow: 1.450 cfm
Approx 11.000 Working Hours

Location : South America

Worldrigs ID: WR570

SOLD
Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2002
Condition : Used

Description :

2002 Ingersoll-Rand T3w Drill Rig - S/N: 6707
IR HR2 900 cfm / 350 psi Air Compressor (Rebuilt in 2013 with 200 Hours
Since Rebuild)
CAT 3406 Diesel Deck Engine - Rated 475 Horsepower with 11,800 Original
Hours (New Head Installed in 2011)
7-Rod Carousel For (4-1/2” X 20’) Drill Pipe
4 Newer Hydraulic Motors On Top Head (All Bearings Replaced in Top
Head in 2010)
6-gal. Hammer Oiler
18 GPM Bean Water Injection Pump
Single Rod Loader
Torque Limit Control
18,000 LBS. Main Hoist
2,000 LBS. Utility Hoist
6” Hammer Pocket
4-Leveling Jacks
300' Feet of Drill Pipe Included
Mounted On AN 2002 International Model 2674 Truck W/A CAT C12, 340
Horepower Engine
52,000 Miles On Truck
VIN. #1HTGLAXT22H515312
Regular Maintenance Done Every 200 Hrs.

Location : USA

Worldrigs ID: WR668
Model : CF15 Drill Rig
Manufacturer : Failing
Year : 1975
Condition : Used

Description :

1975 Failing CF-15 Drill Rig
Mounted on a 1975 LT-9000 truck
600 ft of (3-1/2, 2-3/8 if) drill pipe
DSM table
bit subbs
drill collars assorted bitts to 12-1/4
100 SDS compressor
FM-45 Failing mud pump
mud pan
desander
lots of tools

Location : USA

Worldrigs ID: WR315

Model : Ingersoll-Rand T4W DH Drill Rig
Year : 2015
Condition : New

Description :

Ingersoll-Rand T4W DH Drill Rig (Rebuilt in 2015)
New (0 hours) Caterpillar C18 Diesel Deck Engine
New (0 hours) Ingersoll-Rand HR2.5 1170 CFM / 350 PSI Air Compressor
Rebuilt Spur Gear Drive Top Head
Brand New Chain, Sprockets and bushings
Brand New 70,000 LBS feed cylinders
7x4x4 Rod carousel carries 400' ft of (4-1/2” X 25’) drill pipe
New gear box 4-hole
New hydraulic pumps
All hydraulic motors rebuilt
All hydraulic valves rebuilt
New hoses
All cylinders rebuilt or replaced with new
Coolers Have been clean and tested
New Winches and new cable installed
All valves Rebuilt or Brand New
New Gauges
Mounted on a New 2015 CCC (Crane Carrier Company) Truck with twin-steer
New Cummins Diesel Engine
12R22.5 Tires

Location : USA

Worldrigs ID: WR197

Model : Heli-Rig 700 HP Package
Manufacturer : Generic
Condition : Used

Description :

Mid-Continent U-36 Ae Diesel Electric @ 700 HP, S/D Drawworks,
Lebus Grooved F/1-1/8" Line, Air Drillers Console, 22" Hydromatic Brake,
Hydraulic Tank Pump P/B @ 2 HP Electric Motor, P/B Ge 752 Traction Motor,
with Blower, @ 1000 HP,All Mounted Covered Skid with Fluorescent Lights,
Ruffneck Heater, Master Skidded

Mast :
Parco 131' H x 17'8" W Cantilever Mast, 360,000 lbs Sheaves, Pin-Type, Crown Block,
(5) 36" Sheaves, 46" Fastline Sheave, 1-1/8" Line, 4" Standpipe, Crown Safety Platform
Racking Board, Tong Counterweights, Ladder, Derrick, Climber, Mast Stand,
Fluorescent Lights.

Sub :
Parco 22' H x 25' W X 35' L Self-Elevating Substructure, Self-Skidded, Rotary Beams,
Stairs, Safety Rails, Deadline Anchor, Skidded with V-Door, 42" H x 5' W x 32' L,
2- Section Catwalk with Steel Deck

Top Drillers House :
10' H x 8' W x 20' L Rd Top Doghouse with 3' l Porch, Knowledge Box, Lockers,
Lights, Bench & Cabinet Storage, Remote Closing Unit, Skidded

Scr House:
Baylor Model Se-33-Ba-301, 3-Bay Scr Drive System, S/N: 1001-61054, 600 Vac,
60hz Input, Multiple Controlled Dc Outputs At 0-750 Vdc, Allen Bradley
Switch Gear & Baylor Instrumentation, (2) Marcus Transformers, (1) 600-400 Volts
(1) 460-208 Volts, Mtd In 10' H x 10'6" W x 20'l House, Lennox T-Class Heat/Air Unit,
Emergency Lights, Skidded.

Generators :
(1) Caterpillar 600kw Generator, P/B CAT 3412 Diesel Engine (S/N 81z0127),
Electric Start, Radiator, Gauges,
(1) Bbc 715 700kw Generator Set, P/B Cat 3412 880hp Diesel Engine
S/N 38s2v356, Air Start, Radiator, Gauges,
Both Mounted in a Skidded 10' W x 36' L Generator House, Fluorescent
Lights, Day Tank,

Location : USA

Worldrigs ID: WR331

Description :
 

The RB 15 enables the user to drill with the following methods, with borehole
diameters 4” (108 mm) to 24” (609 mm):
 

Rotary-drilling with direct circulation
Rotary-drilling with reverse circulation Auger-drilling
 

Percussion core drilling (ram coring)
Wire-line core drilling 
Down-The-Hole hammer drilling (direct / reverse)
Free-fall drilling
Geothermal Drilling with DoubleRotation-Head
Inclined Drilling max.45 degrees
 

Additional rig components
Addit. to specifications overleaf
Foam pumpe
Line oiler (for DTH)
Free-fall winch
Hose winch
Percussion drilling device
Hydraulically driven Gen-set
Hydraulically driven welding-set
Rod handling arm
Rod box
 

Base carrier : Crawler base
 

Crawler width / Track shoe width : 2.450 / 500 mm
Transport dimensions L / W / H Diesel Engine (water-cooled) : 10.000 / 2.540 / 3.200 mm
Exhaust Emission Standard : EPA / Carb Tier 3, EU Stufe 3A
Rated output : 205 kW @ 2.200 U/min (rpm)
Diesel tank capacity : 280 l
Feed device (hydr. cylinder)
Push-down / Pull-back force : 70 / 140 kN
Feed speed : 0 - 0,8 m/s
 

Power swivel : L130
Gear select, 3 speeds
Torque at 0 - 34   rpm : 11.750 Nm
Torque at 0 - 100 rpm : 4.150 Nm
Torque at 0 - 320 rpm : 1.200 Nm
 

Chuck & break device : HSB 178.300
Clamping diameter max. / min. : 170 / 51 mm
Max. breaking torque : 41.000 Nm
 

Outrigger cylinder
Max. stroke : 600 mm
 

Mast head with hydr. swing-out device
Swing-out displacement : 700 mm
Swing-out force : 8 kN
 

Clamping device
Max. clearance diameter : 400 mm
Max. casing nominal diameter : DN 255
Max. clamping force : 300 kN

Winches
Main winch
Line pull 1st layer : 95 kN
Wire rope diameter / rope length : 20 / 130 m
Coring winch
Line pull 1st layer : 20 kN
Wire rope diameter / rope length : 8 / 300 m
Auxiliary / percussion winch
Line pull 1st layer : 26 kN
Wire rope diameter / rope length : 10 / 49 m

Pumps
Triplex piston pump
Discharge / Operating pressure : 270 l/min / 40 bar
Duplex piston pump
Discharge / Operating pressure : 450 l/min / 20 bar
Eccentric screw pump
Discharge / Operating pressure : 350 l/min / 24 bar
Centrifugal pump
Discharge capacity / Op.pressure : 1.500 l/min / 8 bar
Suction pump
Discharge capacity / Suction height : 5.300 l/min

Screw type compressor Compressor
Discharge / Operating pressure : 7 m³/min / 15 bar
Rotating casing table : VDT 324  VDT 419

Torque : 13 / 20 kNm  30 / 45 kNm

Worldrigs ID: WR852
Description :

1989 Schramm T-660 Drill Rig
Detroit 8V92 Diesel Deck Engine (less than 4000 hours since
complete rebuild with preheater)
GHH 900 cfm / 350 psi Air Compressor (Rebuilt, less than 500 hours,
with clutch)
Jib-Boom
Bean water injection pump
360 ft of drill pipe (20ft x 4-1/2"), table bushings & basic tooling included
7 Rod Carousel Lazy Susan
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a GMC White Brigadier Truck (60k+ miles on gauge)
Cat 3208 (Rebuilt transmission less than 2000 miles ago)
Very good tires
Note: Replaced upper chains when the motor were rebuilt about 3500 hours ago

Current repairs needed we are aware of:
Truck CAT 3208 engine starts very hard but once it starts then it runs fine and
runs good (Rebuild time approaching soon)
Traverse cylinders leak small amounts of oil
Deck deck engine leaks small amounts of oil
Compressor clutch work manually only

Location : USA

Worldrigs ID: WR705
Model : T625 Drill Rig
Manufacturer : Reichdrill
Year : 1994
Condition : Used

Description :

1994 Reichdrill T625 Drill Rig
Sullair 900 cfm / 350 air compressor (Rebuilt in 2016)
Cummins 855 NTA Diesel Deck Engine (Rebuilt in 2017)
- rated 435 HP at 1800 RPM - S/N: 34071 & CPL: 1576
Bean Water Injection Pump 7 GPM
Hammer Lubricator
28,000 lbs of Pullback
4,000 lbs/ft of torque
6 Rod Carousel
700 ft of used drill pipe (20 ft x 4-1/2" x 2-7/8") & basic tooling included
Hydraulic Leveling Jacks
Mounted on a 1995 Ford LTN 8000 Truck
Diesel Engine - rated 300 HP (reman replaced old engine)
37,000+- miles
Note: Radiators was tested and repaired as needed & New table in 2018
37 ft L x 8 ft 6" W x 12 ft 6" H and 52,500 lbs weight

Location : USA

Worldrigs ID: WR783
Model : Simco-Style Top Head Drive Drill Rig
Manufacturer : Generic
Condition : Used

Description :

Simco-Style Top Head Drive Rotary Drill Rig
Simco Swing-Away Top Rotary Hydraulic Power Head
Swivel
16 ft. 4 in. mast length (retracted), approximately 25 ft. length mast (extended)
Rod Box
Cathead
Winch
4 cylinder Deutz Deck Engine
Control Panel
Mounted on a Ford F600 diesel powered truck
4 Hydraulic stabilizing jacks
Clean, ready-to-work machine

Location : USA

Worldrigs ID: WR597
Model : T-650 Blast Hole Drill Rig
Manufacturer : Reichdrill
Year : 1989
Condition : Used

Description :

1989 Reichdrill T-650 Blast Hole Drill Rig
1100 CFM / 350 PSI Air Compressor
Rebuilt Cummins KT Diesel Engine
Mounted on an International truck
Rebuilt - Cummins L10 Diesel Engine
DTH Hammer included

Location : USA

Worldrigs ID: WR660
Model : T4BH (Blast Hole) Drill Rig
Manufacturer : Atlas Copco
Year : 2006
Condition : Used

Description :

2006 Atlas Copco T4BH (Blast Hole) Drill Rig
Serial Number: 8294
Cummins QSK19 Diesel Deck Engine
IR HR2.5 1250 CFM / 350 PSI Air Compressor
Dual Motor Spur Gear Power Head
LT Long Tower runs (30ft Drill Pipe)
CCC : Cummins isx 15 , 475hp

Location : Middle East Region

Worldrigs ID: WR827
Description :

1979 Jaswell 1200 Drill Rig
Mounted on a Paystar 5000 Truck
Detroit 8V92T Diesel Deck Engine (newer clutch)
Sullair 900 cfm / 350 psi Air Compressor (Recent Compressor and Radiator)
New Chains and updated pumps, gear box
Has cat walk
Recent Oil change
Mounted on a Paystar 5000 Truck
Detroit 671 turbo diesel engine
newer rear tires
5 +4 Transmission
All newer paint

Location : USA

Worldrigs ID: WR883
Description :

1981 Chicago Pneumatic T-700WH Deep Hole Drill Rig & Package
900/350 on-board air,
mounted on a tandem axle steer Kenworth carrier -75,000# pull-back,
4-rod carousel,
CAT 3406B deck engine recently replaced (less than 500 hours ago),
rebuilt dual top-head motors and planetaries,
rebuilt rotational pump and fan motor/pump,
new Nylotron head guides,
new winch line

Additional equipment included :
3,200ft 4 1/2"  x 30ft drill pipe with tandem axle drill pipe trailer
mounted IR tugger winch,
skid mounted Sullair 900/350 air compressor,
skid mounted 2000 gallon fuel tank,
skid mounted 300 bbl water tank,
skid mounted doghouse,
spare CAT 3406B engine (needs rebuilt),
6" hammer, 12" hammer/stabilizer combo,
12" tri-cone stabilizer,
casing lifters for both threaded and plain-end,
casing slips, break out wrench, J-wrench.

Location : USA

Worldrigs ID: WR844
Description :

1994 Ingersoll-Rand T4W Drill Rig
Rebuilt 2006
Rebuilt Cummins KTA19C Diesel Deck Engine (rated 600 HP at 2100 RPM)
Rebuilt in 2006 a IRH2.5 1070 cfm / 350 psi air compressor
Mounted on a CCC (Crane Carrier)
Cummins L10 diesel engine
50,000 lbs of pullback
Setup for 2-7/8" IF Drill Pipe

The following work was performed when rebuilt:
Rebuild of rig and components
Remanufactured Cummins engine KTA19C 600 HP @ 2100 RPM from Cummins
(upgraded from original 545 HP @ 2100 RPM)
Remanufactured IR compressor HR2.5 1070 CFM @ 350 PSI
Rebuilt funk box Rebuilt or new hydraulic pumps and motor
Rebuilt hydraulic cylinder All new hydraulics and air hose
New and upgraded radiator
New and upgraded air compressor, oil cooler and hydraulic oil cooler
Valve spool rebuilt – new seals and control handles
New feed chains upper and lower – Upgraded
New front leaf springs on carrier
New gauges
New wire harness
Rig and all parts sandblasted and painted grey and red
Rig completely serviced – Ready to drill

Additional tooling :
6” IR QL60 Drive Hammer with Bit
6” IR QL60 Drill Hammer with 4-1/2” x 21.5ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 20ft lead steel with bit
4-1/2” X 25ft 2-7/8 API Drill Rod (11 pieces)
6” Casing Drive Plate
8” Casing Drive Plate
10” Casing Drive Plate
1 - Petol Chain Wrench set up for 4-1/2” Drill Rod and 6” Hammer
1 – Petol Chain Wrench set up for 6” Drill Rod and 8” Hammer
Lincoln Welder with Leads
Oxy/Acetalene Torch Setup

Location : Eastern Region

Worldrigs ID: WR828
Description :

1991 Reichdrill T-650-W Drill Rig
Camion has been repainted
Drill Rig sandblasted
Brakes and boosters has been change
Feed Cylinder redone
Deck engine good
Compressor turns
1300 working hours
Needs some work

Location : North America

Worldrigs ID: WR764
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used

Description :

1994 Ingersoll Rand T4W Drill Rig - S/N: 3909
IR 900 cfm / 350 psi Air Compressor
Cummins KT19 Diesel Deck Engine
Bean Water Injection Pump
Hammer Oilier
4 & 7 Rod Carousel
50,000 lbs of Pullback
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine

Location : USA

Worldrigs ID: WR543

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig
Serial Number T64HB-472
425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on International Fleetstar 1910 A truck p/b Gasoline Engine

Location : USA

Worldrigs ID: WR689
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1979
Condition : Used

Description :

1979 Ingersoll-Rand TH60 Drill Rig
IR 750 cfm / 250 psi Air Compressor - 2 Stage Screw type
Gardner Denver 5X6 Mud Pump (hydraulic driven)
Mounted on a newer 1995 Kenworth T800 Truck
Cummins N14 Diesel Engine - rated 425 HP
4-Motor Tophead with 2-7/8" Threads
200 ft of 20ft x 4.5" x 2-7/8" Drill Pipe
20K Front End
40,000 lbs of Pullback
Rod Box
7-Rod Carousel
Bean Water Injection
Sand Line
Auxiliary PTO for Lift Pump
Two Brand New Batteries
Note: Capable of Handling a Casing Hammer (not included)
2,080 Total Hours (600 hours on it since rebuild in Feb. 2015)
Meter Reads 9,734
The truck is all original
Note: Can be Sold with a service truck and water truck at an extra cost

Location : USA

Worldrigs ID: WR668
Model : CF15 Drill Rig
Manufacturer : Failing
Year : 1975
Condition : Used

Description :

1975 Failing CF-15 Drill Rig
Mounted on a 1975 LT-9000 truck
600 ft of (3-1/2, 2-3/8 if) drill pipe
DSM table
bit subbs
drill collars assorted bitts to 12-1/4
100 SDS compressor
FM-45 Failing mud pump
mud pan
desander
lots of tools

Location : USA

Worldrigs ID: WR682
Model : CME-75 Drill Rig
Manufacturer : CME Drill
Year : 1988
Condition : Used

Description :

1988 CME-75 Drill Rig
Mounted on a newer 1998 Ford 6X4 FT900 Truck
94,866 miles
3 axles
Ford 300 6 cylinder
Gardner Denver 4.5" x 5" FF FXFM Mud Pump,
2 hydraulic Hoists
wireline & cathead
high torque rotary drive
quick disconnect mast
in-out & sideways slide base
140 lb. auto SPT hammer 
3 hydraulic Jacks
hydraulic Auger rack
500 gallon water tank
three locking tool boxes
locking storage under water tank and rig
Re-diamond plated rig body Feb. 2010 (garage keep since)

Location : USA

Worldrigs ID: WR799
Model : T4W LT Range II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2005
Condition : Used

Description :

Ingersoll-Rand T4W LT (Long Tower) Range II Drill Rig
2005 CAT C-12 Diesel Engine (4,000 hours)
Ingersoll-Rand 1170 cfm / 350 psi Air Compressor
70,000 lbs of Pullback (Deep Hole)
4 hole gearbox and 2 hole gearbox
High Torque Spur Gear power head with cushion sub
Bean Water Injector Pump rated at 2000 psi
Mounted on a CCC (Craine Carrier Company)
CAT 3406 Diesel Engine
2400 Gal Fuel Tank with Hose Reels
12V Electric Pump

Mounted on a 32 ft Tandum Axle trailer
Sullair 1150 cfm / 350 psi Air Compressor
CAT C-15 Diesel Engine with 7,000 hours

Hurricane Booster - rated 900 lbs of pressure
CAT 3126 Diesel Engine
Both mounted on a 32' ft Tandum Axle Trailer

120 Pipe of T4 style drill pipe (3,000 ft) 3-1/2" Reg Pin and Box
5 check valve subadapters
Pipe and adapters are all loaded on 2 tandum axle flat bed trailers
Drill Rig Base or Platform
14" tall 35 ft long 10 ft wide with folding ramps and fold down walkways
38 ft tandum axle trailer with roller for moving
IR-120 Hammer with 12-1/4" bit x 11" x 20 Stabilizer
IR-TD-90 Hammer with 8-7/8" bit x 8" x 20 Stabilizer
IR QLX-60 Hammer w/ 6-1/4"bit, 6" by 25ft Stabilizer
3 sets of Casing Clamp type Elevators for 4-1/2", 7" & 9-5/8"
Washington rotation head diverter assembly with adaptter plates
35 ft of blow pipe with hammer unions
2 complete Petol wrenches, Misc Table bushings & Wrenches Forks and Subs

Location : USA

Worldrigs ID: WR757
Model : T500XD Telemast Drill Rig - Trailer Mounted
Manufacturer : Schramm
Condition : New

Description :

New 2015 Schramm T500XD Telemast Drill Rig
Trailer Mounted
Rated 1520 HP Diesel Power
60° PAD Walking System
Tilting Top Drive
Control Room
Loadsafe® XD Automated Pipe Handling System
Hands Free Power Breakout
500,000 lbs. (226,796 kg) hook load rig in a portable over the road package
80,000 lbf. (356 kN) hydraulic pulldown for precise weight on bit control
Control cabin with joystick controllers for drilling and pipe handling
operations Self-erecting in a matter of hours without the use of a crane
Power breakout, table and slips maximize safety on the drill floor
LoadSafe XD hands-free Range III pipe handling system included
Crew of three typical
Optional dual fuel configuration available
no draw works on this rig, has hyd powered hoist and rotation

Note: Major Price Reduction to Sell Quickly

Expected fuel consumption per hour?
Model: MTU 12V-2000TA DDEC Tier 1
Power: 760 bhp (567 kw) @ 1,800 rpm
Torque: 2,188 ft-lb (2,967 N-m) @ 1,800 rpm
Displacement: 1,458 cu. in. (23.9 l)
B.S.F.C.: .338 lb/bhp-hr @ Maximum Power (206 g/kw-hr)
Fuel Consumption: 36.2 g/hr @ Maximum Power, 27 g/hr @ Average Load
Horsepower Ratings: +2%, -0%
Altitude Performance, All MTU Series 2000 Engines - % of Rated BHP:
5,000ft (1524m) = 99.0% at 1800 rpm
10,000ft (3048m) = 97.0% at 1800 rpm
15,000ft (4572m) = 94.5% at 1800 rpm

Location : USA

Worldrigs ID: WR885
Description :

1986 Jaswell J1200 Drill Rig
Mounted on a 1986 International Paystar 5000 Truck
Cummins 350 HP diesel engine  
20 speed spicer transmission
20k front axle & 44k rear axles
Odometer works and reads 96,000 miles
90% rubber all around
Cummins N14 mechanical - rated at 450 HP diesel engine
Sullair 900 cfm / 350 psi air compressor with cooler mounted on the side

Comes with : 360 ft of drill steel, two 6" hammers, and 8" hammer stabilizer
6" QL60 Hammer and the 8" Hammer & 8-1/2" Bit. All hand tools included
New diamond chains top and bottom, new sprockets, pins and bushings in 2018
Rebuilt twin disc pto in 2018. Replaced rear main seal in the deck engine 2018
New crown shaft in 2018, pillow block bearings were used but in good condition
Two piston bean pump. Tube style tower same as J2400
1000 hours on it since repairs in 2018

Location : North America

Worldrigs ID: WR700
Model : T660W Drill Rig
Manufacturer : Schramm
Year : 1996
Condition : Used

Description :

1996 Schramm T660W Drill Rig
Deutz Tier III Diesel Deck Engine (350-400 hours since new)
Sullair 900 CFM / 350 Air Compressor - rated 1900 RPM
Bean Water Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Hydraulic Pull Down & Pull Back
Hydraulic Cooler
Equipped with two extra hydraulic Ram to operate casing hammer 4-1⁄2” x 25 ft
Drill Steel
3 Outriggers
Complete Part & Service / Repair Manual
Breakout Wrench
Hydraulic Grout Pump
Cyclone Dust Control
Hydraulic Adj Jib & Rotation Jib
Extra Sandline Winch
Multiple speed top head motors
Mounted on a Ford L8000 Truck
Cummins 6CTAA 8.3L Diesel Engine - S/N: 60312850 & PIN#:3802644-PX
(newer engine installed with 7,000 miles since) - Rated 250 HP at 2200 RPM
(Reman Plate numbers: 3922471LA & M051807002B & P-7100).
Air & Mud Drilling Capabilities

Location : USA

Worldrigs ID: WR860
Description :

Schramm TXD90 Drill Rig
Diesel Deck Engine
Mounted on a Truck

Included as a package :
1,519 feet of 3-1/2" Drill Pipe
6" Collars = 2 Joints (1) 25ft Long (1) 12ft Long
All Subs needed to drill
Elevators

Location : USA

Worldrigs ID: WR762
Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2007
Condition : Used

Description :

2007 Atlas Copco RD20 Range III Drill Rig & Pipe Handling System
Hours 27,319+
Heavy‐duty Derrick and Top head Drive pullback of 120,000 lb
51 ft. 7" in. clearance - plenty of room for 30 ft. drill pipe
8,000 ft‐lb. Spur gear power head
Cummins QSK‐19C Diesel Deck Engine - rated 755‐hp
IR HR2.5 1,250 cfm / 350 psi Air Compressor over/under Air End
Mounted on a CCC (Crane Carrier Company) Truck
Caterpillar C13 Diesel Engine - rated 380 HP
Mileage  32,531+
Note: Package Includes:
2014 Foremost Pipe Handler 4000 Series (hydraulic pipe handling system -
hands free) on a 2 axle Trailer
The engine, compressor and hydraulic pumps are mounted on a floating
power‐pack

Location : USA

Worldrigs ID: WR562

Description :

Drawworks:
Superior 1000M New (2006) Single Drum Drawworks, 1,000 Hp
Lebus grooved for 1-1/4” Drilling Line, Air operated Makeup
& Breakout Catheads, Over-Running Clutch, Air
Driller’s Console, Crown-O-Matic, Right Angle drive for rotary table.

Compound:
2-Engine, In-Line Compound, w/ Right Angle Drive RT
Box For rotary & Draw works drive

Brake:
PARMAC Dual V-80 Hydromatic Brake coupled together

Drawwworks Power:
No. 1 – CATERPILLAR C-18 Diesel Engine S/N# WJH01728,
 600 Hp Rated, w/24 Volt Electric Start, Radiator, Gauges,
OILWORKS C-195-100 Torque Converter S/N3444
 Air clutch
Hours# 21,597
 No. 2 – CATERPILLAR C-18 Diesel Engine S/N# WJH01706,
 600 Hp Rated, w/24 Volt Electric Start, Radiator, Gauges,
OILWORKS C-195-100 Torque Converter S/N1616
 Air clutch
Hours# 21,664

Mast:
DRILLMASTER New 2008 SN#07632 20’1 1”W x 136’H Cantilever Mast,
With a Gross Nominal Capacity of 930,000 Lbs. and a
650,000 Lb. Static Hook Load, Max wind 91 Knots,
 with ten (10) lines. Crown Block w/ (5)42” Sheave Cluster &
1-56”Fast line Sheave grooved for 1-1/4” diameter drilling line.
Each Crown Sheave wire rope groove is flame hardened.
Each Crown Sheave is fitted with Timken roller bearings and grease seals.
Derrick complete with Crown Safety Platform, 20 finger Racking Board W/ electric mule,
Bridal Lines, Tong Counter Weights, Survey Line Sheaves,
Tugger Sheaves, Ladder, Derrick Climber, Geronimo line,
4” Standpipe & Manifold and
Derrick Stand.
Last Certification 8/23/2012

Substructure:
DRILLMASTER New (2009) 29’10”W x 20’H x 48’8”L
(4) Box-On-Box Substructure w/ Rotary Beams, V-Door Ramp,
Stairs, (2) Air Receiver Tanks, NATIONAL Deadline Anchor,
Safety Rails, inside Catwalk Trolley, 7’W x 14’L built in Tool
Room (ODS) (3) Stairs, Outside wall Winterized, Jacking door,
12’ X 12’ Setback spreader, internal stairway, Vapor proof lighting,
Skidded with oilfield tail rolls

Pump: (Primary)
HT F-1000 Triplex Mud Pump New 2006,
S/N HT 20060088, 1,000Hp.
w/ LANZOU Pulsation Dampener S/N HT20060070,
MF 5,000 Psi. Pressure Gauge 
FIVE STAR 6”x8”x14” Charging Pump S/N5268 p/b TECO 75 Hp. Electric Motor,
 Chinese 3”Shear Relief Value, Master Skidded w/ (2) Engines belt compound

Pump Power:
CATERPILLAR C-18 Diesel Engine S/N WJHO1283,
575 HP w/24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive EATON 18CB500 Air Flex Clutch,
Mounted Pump Master Skid.
Hours # 17,376
CATERPILLAR C-18 Diesel Engine S/N WJH01322,
575 HP w/ 24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive EATON18CB500 Air Flex Clutch,
 Mounted Pump Master Skid
Hours#16,277

Pump (Secondary)
HT F-1 000 Triplex Mud Pump New 2006,
S/N HT 20060070, 1,000 Hp.
w/ LANZHOU Pulsation Dampener S/N HT20060069,
MF 5,000 Psi. Pressure Gauge
Five Star 6” x 8” x14” Charging Pump S/N5268 p/b Worldwide 75 Hp.
Electric motor,
3” Shear Relief Valve, Master Skidded w/ (2) Engine belt compound

Pump Power
CATERPILLAR C-18 Diesel Engine S/N WJH-00457,
575 HP w/ 24 volt Electric Start, Radiator, Gauges,
V-Belt Drive, EATON 18CB500 Air Flex Clutch,
Mounted pump Master Skid.
Hours#13,788
CATERPILLAR C1-8 Diesel Engine S/N WJH-00373,
575 HP w/ 24 Volt Electric Start, Radiator, Gauges,
V-Belt Drive, EATON 18CB500 Air Flex Clutch,
Mounted Pump Master Skid.
Hours#16,643

Rotating Equipment:

Rotary Table
Chinese ZP 27-1/2”, New 2006, complies with API split master bushings,
W/ drive shaft coupling.

Swivel
Ideco 300

Kelly
5-1/4” x 42’ Hex Kelly W/ HDS Kelly Drive Bushing

Kelly Spinner
OWI 1500 Kelly Spinner S/N 00475B w/ (2) Air Motors, New

Kelly Valves
Upper Kelly Valve.
Lower Kelly Valve

Travelling Equipment
Sentry Rig Equipment Company
260 Ton Capacity New 2006
4G260 Traveling Block w/ (5) 36” Sheaves, 1-1/4” Line,
Unitized “Hydra-Hook” 260 Ton Capacity

Blowout Preventer and Valves
1 Each -13-5/8" X 5000# Jiangsu Xianz hong Petroleum 
Double Gate BOP, Top & Bottom Stud configuration
Including - 1set of 5" Pipe Rams Blocks & 1set of Blind Rams,
With 2 - 4" outlets on each side of Body of BOP

1 Each - 13-5/8" Jiangsu Xianz hong Petroleum  ANNULAR BOP
Includes rubber element

1 Each - 13 5/8" X 5000# Type D Drilling Spool W/ - 2" Side Outlet & 3" Side Outlet
[Matched To Choke Manifold

1 Each - Choke Manifold - 3" X 5000# Complete
 Inc - Steel Flex Line W/ Flanges To Connect
To BOPS or Drilling Spools

Closing Unit
2008 Jiangsu Xianz hong Petroleum Model FXQ640-6
Closing Unit Accumulator, 6 Station,
 Rig Floor Controls and monitor panel,
Complete W/ 15 Bottles, 30 HP Cat 3517 Charge Pump, 21 Air Pumps, & set up
for Nitrogen Bottle Backup
Suitcase Closing Unit Skid 7’-1 0” x 35’ with junk basket

Choke Manifold and Valves
Jiangsu Xianz hong Petroleum Choke Manifold w/ (1) 5-Way Cross,
(3) 4-1/16”x 5M
Gate Valves, (4) 2-9/16” x 5M Gate Valves, (1) Manual
Adjustable Chokes, Hydraulic Adjustable Chokes, Mounted Oil Field Skid.
W/ 2 Kill Valves- & 2-Choke Valves mounted at drilling spool

Rig Houses:
Dog House, DRILLMASTER 9’ 1 1”W x 39’ 1 1”L
Doghouse / Change house Combination w/ 17’5”L
Driller’s House w/ Knowledge Box (5) Lockers, Bench Storage, Heater, Lights.
 5’L Breezeway, 1 7’5”L Change House, w/Bench Storage, (16-Lockers,
Cabinets, Heater & Lights. Oil Field Skidded

Generator/Utility Houses
DRILLMASTER 1 1’10”W x 37’9”L x 11’ 6” T
Utility House w/Lights, Oil Field Skidded to include the following items.

No #1 380 Kw. AC CATERPILLAR Generator Package Powered by Caterpillar C-15
Diesel Engine S/N JRE01986 w/ 24 Volt Electric Start, Radiator, HD Air cleaner Gauges.
Marathon 572RSL4025 Generator End SN# 550989-0506, complete with Oil Field skid.
Hours# 17,278

No #2 380 Kw. AC CATERPILLAR Generator Package Powered by Caterpillar C-15
Diesel Engine S/N JRE01985 w/ 24 Volt Electric Start, Radiator, HD Air cleaner Gauges.
Marathon 572RSL4025 Generator End SN# 550989-0507, complete with Oil Field skid.
Hours# 16,933

NO. 1 GARDNER-DENVER EBE99N New 2006
Electro Saver II Rotary Screw Air Compressor S/N# S237421,
P/b TOSHIBA 30 Hp. Electric Motor, Mounted 240 Gallon Horizontal Tank.
Hours# 15,128

SIEMENS Interlock Panel, 600 Amp 480 Volt Main Lockout Disconnects breakers.

ALLEN BRADLEY Electrical Load center with magnetic starter & breakers,

SQUARE D 225 amp 240 volt panel with breakers

SQUARE D 75KVA Transformer 480 volt to 240 volt

DRILLMASTER 7’9”W x 13”H x 43’1”L Electrical

Suitcase.

DRILLMASTER 2’5”W x 1 3”H x 36’3”L Electrical Suitcases.

Mud System:
DRILLMASTER 9’6”W x 7’H x 34’5”L, 394 Bbl. Suction Tank
10’L Covered Porch, (3) Compartments,
(3) MAX 2000 Mud Agitators p/b TECO 25 Hp. Electric Motors,
Sloped Bottom, Top Mounted Walkways, Safety Rails, Lights, Oil Field Skidded.
FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5284, p/b BALDOR 75 Hp. Electric Motor.
FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5284, p/b BALDOR 75 Hp. Electric Motor.
With internal jetting system, 3 dump gates,

DRILLMASTER 9’6”W x 7’H x 34’7”L, 394 Bbl. Shaker Tank
10’L Covered Porch, (3) Compartments
MAX 2000 Mud Agitator Agitators p/b TECO 25 Hp. Electric Motors,
Sloped Bottom, Top Mounted Walkways, Safety Rails, Lights, Skidded.
With internal jetting system, 3 dump gates,

FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5269,
p/b BALDOR 75 Hp. Electric Motor.

FIVE STAR 6”x8”x14” Centrifugal Mixing Pump S/N 5283,
p/b BALDOR 75 Hp. Electric Motor.

SHALE SHAKER, Fluid Systems Inc., Single Screen,
Linear Motion Shale Shaker S/N2450,

SHALE SHAKER, Fluid Systems Inc., Single Screen,
Linear Motion Shale Shaker S/N3089,

NOI DSN-ZH-10CTX Desander S/N 8714-5732,w/ (2) 10” Cones.

NOI DSL-10GG-4CTX Desilter S/N 8714-5731,w/ (10)4” Cones.

DRILCO “Deep Pit” Degasser p/b TECO 10 Hp. Electric Motor

Bubble Buster: Geothermal Type Bubble Buster

Mud House
DRILLMASTER 9’ 1 1”W x 26’L Mud House w/Mud Hopper, Test Sink,
Ventilation Fan, Electric Heater, Lights, Double Side Door, (2) End Doors, Skidded. 
Includes 7’H Tri-Stand on one end the other end sets on suction tank.

Fuel Tank
DRILLMASTER 7’1 1”Wx8’Hx30’L, 13,860 Gallon Fuel Tank
w/ (2) AMT 1/2 Hp. Fuel Transfer Pumps p/b BALDOR 1/2 Hp. Electric Motors,
with Three (3)Compartment, Combo Lubester Oilfield Skidded.

Water Tank
DRILLMASTER 10’10”W x 8’1”H x 35’L, 529 Bbl. Water Tank
w/ 10’L Covered Extension, Pump Room, OilField Skidded
FIVE STAR 3”x4”x1 1” Centrifugal Water Pump
S/N 5420, p/b TECO 20 Hp. Electric Motor.
FIVE STAR 3”x4”x1 1” Centrifugal Water Pump
S/N5267, p/b TECO 20 Hp. Electric Motor.

Instrumentation
Weight Indicator
Mud Gauges.

Ancillary Equipment
DRILLMASTER 5’W x 2’4”H x 60’L, 2-Section Catwalk w/ Steel Deck and stands for string blocks.
Pipe Racks 5 Sets 29” x 30’ 1 set 29” x 12’ 1 set 41” x 30’
FIVE STAR “Retriever” Electric Measuring Device S/N 862, w/ 15,000 Ft. of. 092 Wire line
2 sets drill pipe elevators 5”
2 sets of drill pipe slips 5”
2 sets of drill collar slips 7” & 9”
2 sets tongs with all head for pipe & casing
2 sets of safety clamps
Mud box  with 5” rubbers
108” X 4” elevator bails
Crossover, bottom hole, lifting Subs
Air Hoist Air Wrench, Model HUL40, S/N-REM10370, 9000 lb. Pull Rating
Air Hoist Air Wrench, Model KSUL, S/N-REM13962, 10,500 lb. Pull Rating
4,000 Ft. of 1-1/4” Drill Line, Mounted Spooler Stand
3-1/2” X 5,000 Psi. Rotary Hose
Vibrator Hose 2 Each 3 ½” x 18’
Rat hole
Mouse hole
8 rig matting boards
Small hand tools & wrenches
Fluorescent & Mercury-Vapor Rig Lights & Wiring Explosion proof
Atco Office/ living shack all electric w/ oil field skid

Worldrigs ID: WR847
Description :

1995 Ingersoll-Rand T4 BH (Blast Hole) Drill Rig
S/N: 4138
Cummins KT19 Diesel Deck Engine - rated 525 horsepower
IR HR2 900 cfm / 350 psi Air Compressor
Spur Gear Power Head with 2 hydraulic motors
37,500 lbs of pullback
7 Rod carousel
Hammer lubricator
Dust collector
100 ft of (4-1/2" x 25ft x 3-1/2"API thread) drill pipe
Air conditioning front and back cabs
Mounted on a 1995 CCC (Crane Carrier)
Cummins M11 Diesel Engine
8LL speed transmission

Note: Cost extra to convert to T4W water well drill rig with repairs.

Location : USA

Worldrigs ID: WR610
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1989
Condition : Used

Description :

1989 Ingersoll-Rand TH60 Drill Rig
Ingersoll-Rand 825 cfm / 350 psi Air Compressor
Gardiner Denver 5x6 Duplex Power Mud Pump
Pulse Injection Pump 1lt/min - rated 70bar
Cat Water pump 38 lt/min - rated 69 Bar
Gearmatic Winch Model 35 single speed with automatic brake and free-fall attachment 12000 kg @22 metres /min.
Capacity 112 metres of 14mm cable
Weldco Casing Hammer
Pulldown (30,000lbs) 13,610 kg. & Holdback (30,000lbs) 13,000kg
Rotation torque (60,000 in-lb) 692 kg-m & Rotation speed 0-100 rpm
Mounted on a Hendrickson Truck (8x6) 6 wheel drive
Detroit 8V92TA V8 Diesel Engine - rated 427 hp
400' ft of drill pipe & tooling & spare parts are included

Location : Western Region, Europe

Worldrigs ID: WR734
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1981
Condition : Used

Description :

1981 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine
IR 900 CFM / 300 Air Compressor (Inline screw type)
Water Injection Pump
Oil Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Pull Down & 50,000 lbs of Pull Back
18” Table Opening
Hydraulic Cooler
4 & 7 Rod Carousels
4-1/2” x 25ft Used Drill Pipe
3 Outriggers
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
Complete Part & Service / Repair Manual

Location : USA

Worldrigs ID: WR807
Model : Larson Reverse Rotary Drill Rig - Air Assited
Manufacturer : Generic
Condition : Used

Description :

1982 Larson Air Assisted Reverse Rotary Drill Rig with Substructure
New derrick 120,000 lbs rated
rebult hydraulic system in 2010
Caterpillar 6 cylinder deck engine (spare rebuilt engine in a crate)
double draw works
1" main line, 1" laydown line, 1/2" tail out line

Included as a Package:
Doghouse - Wired, lighted, AC, tool room, Geolograph
40ft 5th wheel, tandem wheel, drill pipe trailer
Substructure 15ft X 12ft 8ft Custom fabricated with guard rails
1,500  ft of 6-5/8" ID IF modified
90ft of 14" drill collars
2010 Atlas Copco 950 cfm / 350 psi SRVS1000 CD6 Air Compressor
1,000 gallon fuel storage tank with transfer pump
King swivel
Pilot Hole bits
Reaming Hole oppener bits
Casing Collars

Optional Equipment that Cost Extra:
Complete testing pump equipment, 6 pumps, 800 ft of 10x3.5x2.437" column
tube she, gear head, discharge head
12 Cylinder Caterpillar test engine

Location : USA

Worldrigs ID: WR771
Model : HTB3KDD Drill Rig
Manufacturer : Howard Turner
Year : 2008
Condition : Used

Description :

2008 Howard Turner HTB3KDD Drill Rig Package
CAT C-7 Diesel Engine - rated 260 BHP
6 Cylinder Diesel 2000 MOD NEW
ALLISON-GM MOD # 653
Drawworks :
H.T.B. CANTON TX.
MOD # HTB5KDD - MUSTANG
Clutches - PO3-10
Twin Disk Brakes - 8 x 28 2 per drum
Drums - 14"
Drums - lea bus for 3/4" cable
Drum Drive - 350 hp deran r-angel
25,000 single line pull to 40,000 lbs
Double 120 Chain
Mast : 62ft X 6ft X 3ft HTB - 150,000 #
Carrier : 50ft tandem axle
Swivel : 72 Ton - 144,000 Pounds
JIB Winch
Hydraulics : 20 gpm, 2000 psi. | PTO Driven from Allison Transmission
Drilling Depth : 6,000 feet
Hours : 3087

Extra Item Available(for extra cost) :
2000 Mud Cleaning System FXZ Gardner Denver mud pump
Mounted on a TRA 48ft Trailer 2000 Olympian 60 kW Generator (8,376 Hours)
1990 Ford 9000 - Equipped with winch for loading pipes
Trailer designed for loading pipes with HTB Drilling Rig sold with
2000ft pipes (5” Drill pipe whith 3.5 IF con/ 13.30 lbs)
Tiger 500 Gallon Fuel Tank
Drill colars 6′′ x 28ft ( 2pcs)
3 1⁄2" bottel neck elevators
Pipe Elevators
Drag bit
Tricone bit
Rods 3-1/2′′ x 30ft
Trush Pump
Casing Elevator
Bit 26"
Sub-base

Location : USA

Worldrigs ID: WR854
Description :

Gus Pech 1000R Drill Rig
Set up for Mud Rotary & Auger
Mounted to a 1989 International 1900 Truck
5 speed transmission 2 speed rear
1936+ hours on rig
3 x 4 centrifugal mud pump
3" plumbing to side swivel
450 ft of (4.5″ x 3-2-7/8") drill pipe & holds 225 ft on board the pipe rack
Mud pan attaches to back of rig for transport
Comes with CAT head and auger attachment
3 winches
Jib winch Pullmaster winch 8500 lbs with rapid reverse
wire line for test sampling
2000 lbs sandline
Developmental air compressor
Tophead slides off pole to set pipe
Hydraulic Leveling Jacks

Location : USA

Worldrigs ID: WR777
Description :

Mayhew 1000 Drill Rig
Mounted on a 1999 Sterling Truck
300 ft of 2-3/8" × 20 ft drill rod
20 ft stabilizer
Hydraulic pull down
3 leveling jacks
Mud pan
Sandline
5×6 Mud pump on board
Two fuel tanks
Some tooling

Location : USA

Worldrigs ID: WR145

Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used
Year : 1989

Description :
 
1989 Simco 2800 Drill Rig
Mounted on a 1989 F600 Truck with Diesel Engine
20' stroke in the tower (10000 lbs of thrust & 4000 lbs rotation)
Mission 2x3 mud pump
Sullair compressor
200' ft of simco pdg drill pipe
Mud Pan attached to the truck
 

Location : USA

Worldrigs ID: WR856
Description :

1992 Ingersoll-Rand T2W Drilling Rig & Package
T2W Drill Outfitted a follows:
IR 900 CFM / 350 PSI Air Compressor
Moyno centrifugal mud pump
500ft of drill pipe on truck (2-7/8” IF), 8-1/2 button bit with stabilizer,
5” hammer, crossover subs included
Mud pan
Mounted on Volvo truck
Cummins N14 diesel engine

Package Includes :
1994 Peterbilt water truck
Grout mixer
2000 gallon in-bed water tank
Auxiliary fuel tank behind cab

Location : USA

Worldrigs ID: WR454

Model : RD20 II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1993
Condition : Used

Description

1993 Ingersoll-Rand RD20 Range II Drill Rig - S/N: 3987
Cummins KTA19 Diesel Deck Deck Engine @ 600 HP
7 Rod Carusel
Cat 2520 water injection pump
Hammer Lubricator
Hydraulic Leveling Jacks
Mounted on a 1993 Central Manufacturing Truck with 4 axles
Cummins L10 Diesel Engine
VIN number: PGV84002
Note: No Air Compressor on board as of now (was a IR 1050/350)

Location : USA

Worldrigs ID: WR597
Model : T-650 Blast Hole Drill Rig
Manufacturer : Reichdrill
Year : 1989
Condition : Used

Description :

1989 Reichdrill T-650 Blast Hole Drill Rig
1100 CFM / 350 PSI Air Compressor
Rebuilt Cummins KT Diesel Engine
Mounted on an International truck
Rebuilt - Cummins L10 Diesel Engine
DTH Hammer included

Location : USA

Worldrigs ID: WR802
Model : 2800 HSHT Drill Rig
Manufacturer : Simco
Year : 1989
Condition : Used

Description :

1989 Simco 2800 HSHT Drill Rig
8805 hours
Wisconsin VG4D gas deck engine
4x3 Centrifugal mud pump powered by Deutz F4L921 diesel engine (1853 hours)
Mounted on a GMC K3500 Truck 4x4
454 gas engine with 182,638 miles

Location : USA

Worldrigs ID: WR760
Model : H800
Manufacturer : Generic
Condition : Used

Description :

Geospace H800 Drill Rig
Powered by Cummins Diesel Engine
Mounted on International Truck

Location : USA

Worldrigs ID: WR862
Description :

2011 Schramm RC685 Exploration Drill Rig
MTU V2000 Diesel Deck Engine
Sullair 1350 cfm / 500 psi Air Compressor
Hours : 12,317
Miles : 7,129
Boart Longyear Rod Handler
Hydraulic Pumps
Collector Box & Cyclone
Drill Table Opening : 22 inch
Rod Spinner & hydraulic breakout wrenches
Rated Depth Capacity : 5-1/2" diameter hole to 2,300 feet deep
Rated Pullback : 94,000 lbs
CAT Walk
Hydraulic Leveling Jacks
Mounted on a 2012 International Truck
MaxxForce Diesel Engine
Misc Drill Tooling for an extra cost (in pictures) Stablizer,
Hole Opener, Collar, Land Plates

Note: Set up for RC (Reverse Circulation) minerial exploration & mining.
This is not a T685 model for water wells

Location : USA

Worldrigs ID: WR838
Description :

Foremost DR-40 Crawler Drill Rig
700 hours
Cummins Diesel Engine
24" Tracks
1250 CFM / 350 PSI Air Compressor
Water Injection Pump
Winch for rods
Telescopic boom
Mounted on a Tracks carrier

Location : USA

Worldrigs ID: WR769
Model : Drill Rig
Manufacturer : Gus Pech
Year : 2008
Condition : Used

Description :

2008 Gus Pech Drill Rig
5,000+ Hours / Miles on Freightliner Truck
3,500+ Hours Drill
Overhauled at Gus Pech Factory in 2017
Sullair 700 cfm / 200 psi Air Compressor
7x10 Centerline Mud Pump
Tilt Power Head
450 hp Mercedes Diesel Engine
set up for Water Wells
estimated rig weighs 48660 lbs, 8ft 6” W, 13ft H, 37ft L

Location : North America

Worldrigs ID: WR610
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1989
Condition : Used

Description :

1989 Ingersoll-Rand TH60 Drill Rig
Ingersoll-Rand 825 cfm / 350 psi Air Compressor
Gardiner Denver 5x6 Duplex Power Mud Pump
Pulse Injection Pump 1lt/min - rated 70bar
Cat Water pump 38 lt/min - rated 69 Bar
Gearmatic Winch Model 35 single speed with automatic brake and free-fall attachment 12000 kg @22 metres /min.
Capacity 112 metres of 14mm cable
Weldco Casing Hammer
Pulldown (30,000lbs) 13,610 kg. & Holdback (30,000lbs) 13,000kg
Rotation torque (60,000 in-lb) 692 kg-m & Rotation speed 0-100 rpm
Mounted on a Hendrickson Truck (8x6) 6 wheel drive
Detroit 8V92TA V8 Diesel Engine - rated 427 hp
400' ft of drill pipe & tooling & spare parts are included

Location : Western Region, Europe

Worldrigs ID: WR783
Model : Simco-Style Top Head Drive Drill Rig
Manufacturer : Generic
Condition : Used

Description :

Simco-Style Top Head Drive Rotary Drill Rig
Simco Swing-Away Top Rotary Hydraulic Power Head
Swivel
16 ft. 4 in. mast length (retracted), approximately 25 ft. length mast (extended)
Rod Box
Cathead
Winch
4 cylinder Deutz Deck Engine
Control Panel
Mounted on a Ford F600 diesel powered truck
4 Hydraulic stabilizing jacks
Clean, ready-to-work machine

Location : USA

Worldrigs ID: WR851
Description :

1979 Portadrill TLS Top Head Drill Rig
60k main line of pullback
40k Tophead Power Drive (swing out)
Sandline
Detroit 8V92TA deisel deck engine
750 cfm / 250 psi air compressor
Leveling jacks
Mounted on an International Truck
Deisel engine
Rebuilt 3 years ago
3 inch western rubber swivel
Retractable table
Note: capable of 16” well with 28” bore
Note: needs paints and leaks fixed (cost extra)

Location : USA

Worldrigs ID: WR603
Model : 3000 Drill Rig
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner Denver 3000 Trailer Mounted Drill Rig
Set up for RC
Brewster 18" removable Table
Single draw works
7 Part Main block
2 Cat heads
New Hydraulic pump system
New Hydraulic winch for Tail out
International DT466 Diesel engine
Trailer mounted
6 Leveling jacks
Hydraulic tower ram
Dog House-- Optional at extra cost
The rig is 12’ 6” tall when connected to a day cab tractor. The width is 8’

Location : USA

Worldrigs ID: WR886
Description :

2012 Schramm TXD 200 Drill Rig
serial number J135-0216, trailer VIN#: 1K9AD40C1C3268138.
Detroit DDC/MTU 12V-2000 Diesel Deck Engine

Tilt Top Head Drive:
Heavy duty, single reduction gearbox with 4 two-speed disc valve type 
hydraulic motors
Variable rotation speed via HRC control
Torque: 0-90 RPM @ 17,750 ft-lbs (24,066 N-m)
0-180 RPM @ 7,670 ft-lbs (10,399 N-m)
Rotation Speed: 0 - 180 RPM · 

Feed System:
50 ft (15.24 M) head travel
200,000 lbf (890 kN) hoist capacity
100 fpm (30.5 m/min) hoist speed
32,000 lbf (142 kN) pulldown
200 fpm (61 m/min) pulldown speed

Drill Table:
Table Opening : 30" inches (768 mm) diameter with table retracted
Hydraulically retractable slip box

Drill Pipe And Casing:
Range III tubular 30 inch capability

Winch:
Planetary design with spring applied hydraulic release brake
9,600 lbf (42.7 kN) bare drum line pull
150 fpm (46 m/min) bare drum line speed
Hydraulic jib boom swing and extend
Auxiliary winch available
The drills have low wear on the cables, bearing and pivot points as well 
as the Control panel
All are in excellent/very good condition during last inspection
LoadSafe pipe handling systems (hands free pipe loading system)
mounted on Trailers

Package available  each of the following:
Generator House with 2 Maraathon Model 431CSL6202-B211 60 HZ Phase 1 
120/240V 122 KW 504 AMO or 3 Phase 277/480 155 KW 233 AMP poered by 
Perkins 6.6 L 1106 IR 2340 Shop air ,Hyd lift with Honda GX392,4000 Gallon 
feul tank and 4 lights on roof.
Weatherford T425 Triplex Mud pump powered by John Deere 6135 diesel engine 
(Tier IV) - rated 500 HP, 6.50 Plunger 900 PSI, MCM 4x5x14 Super Charge 
Centrifugal pump with soap mixing tanks in back
750 BBL Water tank with hydraulic lift dog house
Crew changing house
Crew House 
8000 ft of drill pipe (4" DP New 30ft 6" NC40)
(4) 6-1/2” Drill collars
Every unit is clean & straight and it is a very nice package in excellent/very 
good condition after inspections in 2020

Location : USA