Worldrigs ID: WR664
Model : 2800 HS (HT) Drill Rig
Manufacturer : Simco
Year : 1992
Condition : Used

Description :

1992 Simco 2800 HS (HT) Drill Rig
Deutz diesel engine on deck
3L6 Moyno pump
Mounted on rubber carrier, powered by 243 Ford gas engine
This rig has been used as recent as February
May have a small oil leak but is all we know that is wrong with it.

Location : USA

Worldrigs ID: WR602
Model : 2000 Drill Rig
Manufacturer : Gardner Denver
Year : 1978
Condition : Used

Description :

1978 Gardner Denver 2000 Drill Rig
Trailer Mounted
2 – Detroit 471 turbo diesel deck engine (comes with spare)
Triple drum draw works
57' ft. tubular mast - rated at 100k
100k pullback draw works
18” Howard Turner rotary table
4-½" x 35’ long Kelly bar
Garner Denver 7x10 duplex mud pump
Cathead
Water break
6 line block
5/8" cable on draw works (Kelly and blocks)
1-hydraulic breakout tong (1 backup)
Spinning chain
4-hydraulic leveling jacks
Rack boards set up for 4-1/2” pipe and 8” collars – single height
Air clutches
200 gallon fuel tank
2 cylinder john bean soap injection pump
3” mud piping
2” air piping
Lay down catwalks with handrails

Location : USA

Worldrigs ID: WR791
Components :

1. The three section pressure compensated load sensed Sauer Danfoss
hydraulic piston pumps are directly coupled to the 6LTAA8.9-360 Cummins
diesel engine via a high quality German drive plate and coupling.

2. The drill mast is a lattice type. The feed system uses a single hydraulic cylinder
connected to a 2:1sheave system connected to heavy duty leaf chains giving
approximately 25,000kg of extraction force with a 6.7 metre stroke.

3. Adjustable hydraulic pressure knob to control and limit the down force
on the feed so the rig base will not be raised up whilst drilling.

4. Adjustable flow control valve to control the speed in which the drill bit advances.

5. Pressure gauges on control panel for calculating either rotation torque or feed pressure.

6. Directional control valves and tilt cylinder with over centre valve and flow limiters

7. A single bent axis piston hydraulic motor coupled to a 4 speed gearbox on the
rotation gearbox.

8. A 400 litre hydraulic oil tank with sight gauge, breather cap, internal suction
screens and 10 micron filter on the return line.

9. 4 x 30,000# support jacks, which are adjustable to level the rig in uneven terrain
and to stabilize the rig.

10. 10” x 7 1⁄2” Duplex type piston mud pump driven by Sauer Danfoss hydraulic Gerola Motor.

11. 8000kg single line pull haul winch.

12. Large Air/Oil fan type oil cooler driven by a hydraulic motor with overrun protection.

13. High quality Cetop type solenoid valves to change between different hydraulic functions.

14. Breakout wrench

15. Rod loading system. (optional)

Worldrigs ID: WR682
Model : CME-75 Drill Rig
Manufacturer : CME Drill
Year : 1988
Condition : Used

Description :

1988 CME-75 Drill Rig
Mounted on a newer 1998 Ford 6X4 FT900 Truck
94,866 miles
3 axles
Ford 300 6 cylinder
Gardner Denver 4.5" x 5" FF FXFM Mud Pump,
2 hydraulic Hoists
wireline & cathead
high torque rotary drive
quick disconnect mast
in-out & sideways slide base
140 lb. auto SPT hammer 
3 hydraulic Jacks
hydraulic Auger rack
500 gallon water tank
three locking tool boxes
locking storage under water tank and rig
Re-diamond plated rig body Feb. 2010 (garage keep since)

Location : USA

Worldrigs ID: WR800
Model : 1500 Drill Rig
Manufacturer : Midway
Condition : Used

Description :

Midway 1500 Drill Rig
10" table retracts but needs cylinder
5-1/2 x 8 GD Pump
New transfer case
4 jacks
Long Derrick
Long Kelly
500 of 2-7/8" drill pipe
Auto car
Caterpillar 3406 Diesel Engine
Bill of sale only

Location : USA

Worldrigs ID: WR810
Model : 1000 Drill Rig & Package
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner-Denver 1000 Drill Rig
14W Drawworks
7-1/2" Rotary Table
Rated for drilling to 1000 ft
Dis-assembled for rebuild
Deck steel replaced in preparation for rebuild
Comes with all components necessary to rebuild back to original specs:
2-stage mast cylinder
3- large 8-1/2 ft outriggers
Piston style WX 1004 compressor (stored inside building)
Gardner-Denver FXG 5x6 mud pump (stored inside building)
24 ft 3-3/8" fluted kelly bar
Little Giant Swivel
Mayhew block for 1000 rig 12" single sheave
292 ft of 3-1/2" flush drill pipe

- 16 ft skid for set up for Gardner Denver 5x8 mud pump, Detroit 353 Diesel
- Engine with Rockford clutch (1600 hours), with 150 gallon fuel tank
- GMC 6-71 Power Unit with Rockford clutch, Rotary table slips, Blue Demon
- Drag Bit 5, spools of cables, assorted bit breakers, 2" relief valve, pipe clamps
and pick up heads, compression coupling and 4" valve, steel mud tank
- 2-3/8" IF to 3-1/2" Reg pipe to bit tubs, pipe spider rings, Rotary Table
- Drill Up slips, shop built collars, T-Pipe for starter, cross over sub adapters, Tool
holder for pipe in table, Petol chain wrenches, regular chain wrenches, Set of
banded v-belts for mud pump skid, 2 rods for GD gear end, bull gear and
eccentric, 2 pairs of sleeves for GD 5x8, valves caps for GD 5x6, cylinder head
for GD 5x6, safe guard and Dodge gear boxes for mud pumps, pinion gear for GD
5x8 duplex 90%, new electric motors 1/2 HP - 3/4 HP - 1 HP stub shaft, power
tower for Keystone Gardner Denver, miscellaneous bits
- 1973 Ford 8000 truck
- Caterpillar 3116 diesel engine
- 10-speedRoadranger transmission

Location : USA

Worldrigs ID: WR797
Model : TXD Drill Rig & Package
Manufacturer : Schramm
Year : 2012
Condition : Used

Description :

2012 Schramm TXD Drill Rig Package
Deck Engine : Detroit Diesel DDC/MTU 12V-2000

Tilting Top Head Drive : Heavy duty, single reduction gearbox
with 4 two-speed disc valve type hydraulic motors  
variable rotation speed via HRC control
Torque: 0-90 RPM @ 17,750 ft-lbs (24,066 N-m)
0-180 RPM @ 7,670 ft-lbs (10,399 N-m)
Rotation Speed: 0 - 180 RPM  

Feed System : 50 ft (15.24 M) head travel  
200,000 lbf (890 kN) hoist capacity  
100 fpm (30.5 m/min) hoist speed  
32,000 lbf (142 kN) pulldown  
200 fpm (61 m/min) pulldown speed

Drill Table : Table Opening: 30 inches (768 mm) diameter with table retracted  
Hydraulically retractable slip box

Drill Pipe and Casing : Range III tubular capability  
30 inch

Winch : Planetary design with spring applied hydraulic release brake ·
9,600 lbf (42.7 kN) bare drum line pull  
150 fpm (46 m/min) bare drum line speed  
Hydraulic jib boom swing and extend  
Auxiliary winch available

This drill has low wear, Cables and bearing and pivot points,
Control panel all are in excellent condition.
Hoses are getting older.
Mounted on a Trailer
LoadSafe pipe handling systems
Generator house 2 155KW Generators powered by Perkins IR Shop Air,
Hydraulic lift jacks and 3 stage closing unit.
500 HP Mud pump Weatherford T425 powered by John Deere 61356.50 Plunger 900 PSI,
MCM 4x5x14 Super Charge pump with soap mixing tanks in back
750 BBL Water tank with hydraulic lift dog house
Crew changing house
Crew House
8000 ft  of drill pipe
4 - 6-1/2” Drill collars
Every pcs is clean and straight nice package.

Location : USA

Worldrigs ID: WR209

Model : B61 HDX Drill Rig
Manufacturer : Mobile
Year : 1990
Condition : Used

Description :

1990 Mobile B61 HDX Drill Rig
Cummins 4bt 3.9 Diesel Engine @ 100 hp @ 2500 rpm
3l8 Pump
8,500 lbs Main Hoist
29' ft Tower
Mounted on a Ford F800 Truck
5 Speed Transmission
Ford 7.8 Diesel Engine @ 210 hp

Location : USA

 

Worldrigs ID: WR471

Model : T7000 Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1981
Condition : Used

Description :

1981 Chicago Pneumatic T7000 Top Head Drive Rotary Drill Rig
S/N: S-81906 (The tag is missing)
Caterpiller 3406B diesel engine
GHH 825 cfm / 300 psi Air Compressor
40' ft mast (note: the mast, carousel & auxiliary winch with
jib have been removed and are stored at another location)

4-Hydraulic outriggers
Mounted on a FWD all-wheel drive CCC (Crane Carrier Chassis)
Cummins diesel engine
6-speed transmission
walking beam rear suspension
with fair size 16.5-22.5 front tires and fair size 11.00-20 rear tires
Showing 4,581 hour on the truck chassis

Note: No Rotary Head

Location : USA

Worldrigs ID: WR862
Description :

2011 Schramm RC685 Exploration Drill Rig
MTU V2000 Diesel Deck Engine
Sullair 1350 cfm / 500 psi Air Compressor
Hours : 12,317
Miles : 7,129
Boart Longyear Rod Handler
Hydraulic Pumps
Collector Box & Cyclone
Drill Table Opening : 22 inch
Rod Spinner & hydraulic breakout wrenches
Rated Depth Capacity : 5-1/2" diameter hole to 2,300 feet deep
Rated Pullback : 94,000 lbs
CAT Walk
Hydraulic Leveling Jacks
Mounted on a 2012 International Truck
MaxxForce Diesel Engine
Misc Drill Tooling for an extra cost (in pictures) Stablizer,
Hole Opener, Collar, Land Plates

Note: Set up for RC (Reverse Circulation) minerial exploration & mining.
This is not a T685 model for water wells

Location : USA

Worldrigs ID: WR879
Description :

1979 Chicago Pneumatic 600 Drill Rig
Detroit 6V93 Diesel Deck Engine
GHH 600 CFM / 300 PSI Air Compressor
320 ft of 4-1/2" x 20 ft Drill Pipe included
Recent Cooler and Drill Head Rebuilt
Mounted on a 1990 Mack Truck
300 HP Diesel Engine

Location : USA

Worldrigs ID: WR865
Description :

UDR 1500 Range III Mobile Drill Rig
Mounted on a 2004 International 5800i Tri-Axle Truck
Engine Hours : 11,804
75 ft - 90,000 lb static hook load capacity
hydraulic raise and lower mast
Rexroth 44,000 lb draw works
Top drive
GD mud pump
CAT C15 14.6L diesel engine
525 Adv horsepower
Engine brake
Eaton Fuller 18 speed manual transmission
352” wheel base
40,000 lb front axle
51,000 lb rears
Rig was almost completely overhauled . Hydraulics , hoses, box  etc.

Location : North America

Worldrigs ID: WR781
Model : DSI QuikDrill Rig
Manufacturer : Speedstar
Condition : Used

Description :

Speedstar DSI QuikDrill
Failing FM-3 Mud Pump
Has Air Compressor (Not Working)
Mounted on 2001 International 4900 Truck
Powered by 7.6 L 466 CID L6 International DT466 Diesel Engine

Location : USA

Worldrigs ID: WR551

SOLD
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1998
Condition : Used

Description :

1998 Ingersoll-Rand T3W Drill Rig
CAT 3406 Diesel Deck Engine
IR HR2 900 cfm / 350 psi Air Compressor
Hammer Lubricator
Bean water injection pump (4 piston)
7885 hours
18,000 LBS Winch
400' ft of (4-1/2” x 20’ 2-7/8IF) drill pipe & basic tooling included
Pipe Rack
Hydraulic leveling jacks
Mounted on 1998 International 2600 Truck
VIN# 1HTGLATT8XH631062
33,148 miles
Caterpillar C-10 diesel engine - rated 350 HP
Jake brakes
10 Speed Spicer Transmission
Power divider
Tires (90%+ Very Good Condition)

Location : USA

Worldrigs ID: WR155

Model : T650 SL Drill Rig
Manufacturer : Reichdrill
Year : 1994
Condition : Used

Description :

1994 REICHdrill T-650 SL (Super Light) drill rig
Serial # 650TBGH00793
Cummins KT19 Diesel Deck Engine
900 CFM / 350 PSI Air Compressor
CAT Water Injection Pump
Hammer Lubricator
Mounted on a 1994 Ford L8000 Truck
Miles 64,899 on gauge
VIN #1FD7W82F7RVA26796
Cummins 7.3L Diesel Engine
Number of Axles4 & Drive Axles2

Location : USA

Worldrigs ID: WR553

Model : CME 75 Drill Rig
Manufacturer : CME Drill
Year : 1987
Condition : Used

Description :

1987 CME 75 Drill Rig
Has 3L6 Moyno Pump
Cat Head
2 Winches
4 Cylinder Gas Engine
The Rig Runs Good
Mounted on a 1988 Ford 750 Tandem Axle (Note: truck is in poor condition).
Also a brand new Auto Hammer in box that can be fitted on the drill

Location : USA

Worldrigs ID: WR832
Description :

2016 Gefco 30K Drill Rig
5,100+ Hours
Mounted on a Peterbuilt 367 6x4 Truck
Cummins rated 550 HP ISX diesel engine (Tier IV)
Sullair 1000 cfm / 350 psi air compressor
Enclosed steel gear box PTO
4 hydraulic leveling jacks
Rotary tophead
6 rod carosel (removed but included in the sale)
15 rod pipe rack
18 gpm Bean water pump
Power sliding holding wrench and table
60” breakout wrench
Pipe spinner
DTH lubricator
Remote controlled jib boom
Moyno 3L8 pump mounted on deck

Location : USA

Worldrigs ID: WR518
Details:

Worldrigs ID: WR826
Description :

2006 Simco 2800HT Drill Rig,
Automatic hammer,
Extruder,
Hydraulic clamps (newer),
Gardner Denver 4-1/2x5 mud pump,
Slide base and head tilt,
2 winches,
High Torque head.
New MAST extension 3 pulleys.
Mounted on a Ford F550 Truck,
Diesel Engine,

Location : USA

Worldrigs ID: WR538

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on Ford truck - VIN T91KVR58157
Engine
Note: No Air Compressor on board (cost extra to install)

Location : USA

Worldrigs ID: WR352

Model: 45C Drill Rig
Manufacturer: CME Drill
Year: 2002
Condition: Used

Description :

2002 CME 45C Drill Rig
With 9278 hours
Auto hammer
Wireline winch
Deutz 3 cylinder diesel engine
Mounted on a 2002 Ford F550 Truck 4x4
148,413 miles

Location : USA

Worldrigs ID: WR372

Model : T650W Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago Pneumatic T650W Drill Rig
425 CFM / 250 PSI Leroi 256 SD Air Compressor
Diesel Deck Engine
Pipe Rack
Mounted on a Truck
Diesel Engine

Location : USA

Worldrigs ID: WR882
Description :

1979 Ingersoll-Rand TH60 Drill Rig,
IR 750 CFM / 250 PSI Air Compressor,
Water injection pump,
Toolbox,
Carousel,
4 hydraulic leveling jacks,
Comes with 420ft Drill Pipe 4-1/2" 2-7/8 IF Thread
Mounted on a 1986 GMC General Truck,
Powered 8V92 Detroit Diesel 475 HP,
All drums & brakes good & Tires 80% estimated,

Location : USA

Worldrigs ID: WR669
Model : SR50 Drill Rig
Manufacturer : Soilmec
Year : 2006
Condition : Used

Description :

2006 Soilmec SR50 Drill Rig
Hours: 10,935 h
CAT C7 Diesel Engine

Location : Europe

Worldrigs ID: WR832
Description :

2016 Gefco 30K Drill Rig
5,100+ Hours
Mounted on a Peterbuilt 367 6x4 Truck
Cummins rated 550 HP ISX diesel engine (Tier IV)
Sullair 1000 cfm / 350 psi air compressor
Enclosed steel gear box PTO
4 hydraulic leveling jacks
Rotary tophead
6 rod carosel (removed but included in the sale)
15 rod pipe rack
18 gpm Bean water pump
Power sliding holding wrench and table
60” breakout wrench
Pipe spinner
DTH lubricator
Remote controlled jib boom
Moyno 3L8 pump mounted on deck

Location : USA

Worldrigs ID: WR214

Model: 650 Drill Rig
Manufacturer: Chicago Pneumatic
Year: 1986
Condition: Used

Description :

1986 Chicago-Pneumatic 650 Drill Rig
GHH 825 cfm / 350 psi Air Compressor
CAT 3406 diesel deck engine
Mounted on Ford truck
diesel engine
Around 1,000 ft of near new drill pipe at extra cost

Location : USA

Worldrigs ID: WR766
Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used

Description :

Simco 2800 Auger / Rotary Drill Rig
Combo auger/rotary
Mounted on 2000 Chevy W4500
Duetz diesel deck engine
25 HP kohler mud pump engine
Mud pump is a 2X3 centrifugal
170 feet of drill rod with 2 roller cone bits
Drill rod is 2-7/8 OD
10 ft extension to the derrick that allows you to work with 20 ft
lengths of pipe
Break out wrench and air compressor on the truck
Truck is a 5 speed cab over
Truck has 135239k and is 2 wheel drive 4 cyl Isuzu diesel
IMT HYD 25CFM @100PSI Air Compressor (?)
Simco thread and set up to run 10 foot lengths

Location : USA

Worldrigs ID: WR850
Description :

CME 75 Drill Rig High Torque Fully Refurbished
Refurbished in 2017
Mounted on a 2006 Freightliner M2 truck
Brand new tires and Transmission
Caterpillar engine
Truck has 300,000 actual miles
Brand new hoses
Automatic hammer
Downhole hammer
6 Cylinder Deutz air-cooled engine

Location : USA

Worldrigs ID: WR551

SOLD
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1998
Condition : Used

Description :

1998 Ingersoll-Rand T3W Drill Rig
CAT 3406 Diesel Deck Engine
IR HR2 900 cfm / 350 psi Air Compressor
Hammer Lubricator
Bean water injection pump (4 piston)
7885 hours
18,000 LBS Winch
400' ft of (4-1/2” x 20’ 2-7/8IF) drill pipe & basic tooling included
Pipe Rack
Hydraulic leveling jacks
Mounted on 1998 International 2600 Truck
VIN# 1HTGLATT8XH631062
33,148 miles
Caterpillar C-10 diesel engine - rated 350 HP
Jake brakes
10 Speed Spicer Transmission
Power divider
Tires (90%+ Very Good Condition)

Location : USA

Worldrigs ID: WR324

SOLD

Model : Soilmax Crawler Drill Rig
Manufacturer : Acker
Condition : Used

Description :

Acker Soilmax Drill Rig
Mounted on a Marooka MST 1500 Crawler Carrier
Hours on Marooka 5,895
Hours on Soilmax approx 500
Also has a removable Hydraulic Chuck, Breakout Wrench, and Table
Table needs to be hooked up to hydraulics

Location : USA

 

Worldrigs ID: WR646
Model : 670 Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1972
Condition : Used

Description :

1972 Chicago Pneumatic 670 Drill Rig
International 510 gas engine (barley runs)
5-speed transmission
CAT 3406 diesel engine
GHH 750 cfm / 300 psi air compressor
Jib & carousel
Includes as a package:
8” hammer w/ 8” bit
6” hammer w/ 6-¼” bit
Jib & carousel
800 ft of 4 inches x 20 ft drill pipe

Location : USA

Worldrigs ID: WR802
Model : 2800 HSHT Drill Rig
Manufacturer : Simco
Year : 1989
Condition : Used

Description :

1989 Simco 2800 HSHT Drill Rig
8805 hours
Wisconsin VG4D gas deck engine
4x3 Centrifugal mud pump powered by Deutz F4L921 diesel engine (1853 hours)
Mounted on a GMC K3500 Truck 4x4
454 gas engine with 182,638 miles

Location : USA

Worldrigs ID: WR216

Model : T450 Drill Rig
Manufacturer : Schramm
Year : 1988
Condition : Used

Description :

1988 Schramm T450 Drill Rig
Diesel Deck Engine
Air Compressor
Carousel
Centrifugal Pump
Pipe Rack
3 hydraulic leveling jacks
Mounted on a Truck
Diesel Engine

Location : USA

Worldrigs ID: WR103

1995 Foremost Barber DR12/36 drill rig
Sullair 1150 CFM / 350 PSI Air Compressor

Worldrigs ID: WR668
Model : CF15 Drill Rig
Manufacturer : Failing
Year : 1975
Condition : Used

Description :

1975 Failing CF-15 Drill Rig
Mounted on a 1975 LT-9000 truck
600 ft of (3-1/2, 2-3/8 if) drill pipe
DSM table
bit subbs
drill collars assorted bitts to 12-1/4
100 SDS compressor
FM-45 Failing mud pump
mud pan
desander
lots of tools

Location : USA

Worldrigs ID: WR790
Model : 500 Drill Rig
Manufacturer : Midway
Year : 1969
Condition : Used

Description :

1969 Midway 500 Drill Rig
Mounted on 1969 Peterbilt Truck
Leroi 100S Air Compressor
Gardner-Denver 5x6 Duplex Piston Mud Pump
New Rear Jacks
Recent Cummins Swap
Transfer case rebuilt in summer 2018
Comes with 200 ft. of 2-7/8” drill pipe
Currently working
Ready to drill

Location : USA

Worldrigs ID: WR576
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1999
Condition : Used

Description :

1999 Ingersoll-Rand T4W Drill Rig - S/N: 7434
Cummins QSK19 Diesel Deck Engine
IR 1050 cfm / 350 psi Air Compressor
Hammer Oiler
Cat Water Injection Pump
Winches
Mounted on a CCC (Crane Carrier Company) Truck
50,000 lbs of Pullback
2 Motor Spur Gear Power Head
4456+ hours on meter
7X4 Rod Carousels
CAT 3306 Diesel Engine
8741+ Miles on gauge
New Paint Job

Location : USA

Worldrigs ID: WR858
Description :

New & Unused 2012 Atlas Copco RD20 Range III XC Drill Rig
Carrier :
Twin H-beam main frame - reinforced 16 in 406.4 mm
5-axle, custom carrier 415 hp 317 kW diesel engine
8-speed transmission Manual with lo - lo and reverse
Tridem rear axles with lockers 23,000 lb each 10,433 kg each
Tandem front steering axles 22,000 lb each 9,979 kg each

Derrick :
Length 61 ft 11 ½ in 18.88 m
Width 4 48 1/2 in 1.23 m
Depth 41 in 1.04 m
Top of table to spindle 51 ft 6 in 5.7 m
Table to ground (rig sitting on tires) 44 in 1,118 mm
Table to ground (jacks fully extended) 92” 2,337 mm

Rig Dimensions :
Height derrick down 13 ft 10 in 4.22 m
Height derrick up 62 ft 6 in 19.05 m
Width 8 ft 4 in 2.54 m
Shipping weight (less tooling) 88,000 lb 40,000 kg

Tip Out Links :
Forged steel 150 ton 136 tonnes
Length 60 in 1,524 mm
Tip out hydraulic cylinder on each link
Angle 0-80° from vertical
Control drillers console

Table & Master Bushing :
Design folding with twin hydraulic jacks
Max opening 26 in 660 mm
API split master bushing 17 ½ in 445 mm
Capacity 60 ton 54.4 tonnes

Rig Performance :
Hookload 120,000 lb 54.4 tonnes
Pulldown 30,000 lbf 13,636 kg
Fast feed up 106 ft/min 32.3 m/min
Fast feed down 180 ft/min 54.9 m/min
Drill feed 29 ft/min 8.8 m/min
Torque 8,000 lbf-ft 10.8 kNm
Speed 0-120 RPM 0-120 RPM
Spindle 3 in 76.2 mm
Swivel Type Multi chevron packings
Opening 2 ½ in 63.5 mm

Location : USA

Worldrigs ID: WR862
Description :

2011 Schramm RC685 Exploration Drill Rig
MTU V2000 Diesel Deck Engine
Sullair 1350 cfm / 500 psi Air Compressor
Hours : 12,317
Miles : 7,129
Boart Longyear Rod Handler
Hydraulic Pumps
Collector Box & Cyclone
Drill Table Opening : 22 inch
Rod Spinner & hydraulic breakout wrenches
Rated Depth Capacity : 5-1/2" diameter hole to 2,300 feet deep
Rated Pullback : 94,000 lbs
CAT Walk
Hydraulic Leveling Jacks
Mounted on a 2012 International Truck
MaxxForce Diesel Engine
Misc Drill Tooling for an extra cost (in pictures) Stablizer,
Hole Opener, Collar, Land Plates

Note: Set up for RC (Reverse Circulation) minerial exploration & mining.
This is not a T685 model for water wells

Location : USA

Worldrigs ID: WR699
Model : 650 S/S Drill Rig - for Parts or Repairs
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic Model 650 S/S Drill Rig
Condition: As Is - for parts or repairs
Used CP 650 S/S parts machine
Comes with control panel
Hydraulic valves in control panel
CO5 Air Compressor (750 CFM / 125 PSI)
Separator Tank
Rears on CCC Crane Carrier Company truck
Wheels
Oil Tank
Operators Cab
Hydraulic Jacks
Other miscellaneous items as shown in pictures
Note: All Items Sold "As Is"

Location : USA

Worldrigs ID: WR879
Description :

1979 Chicago Pneumatic 600 Drill Rig
Detroit 6V93 Diesel Deck Engine
GHH 600 CFM / 300 PSI Air Compressor
320 ft of 4-1/2" x 20 ft Drill Pipe included
Recent Cooler and Drill Head Rebuilt
Mounted on a 1990 Mack Truck
300 HP Diesel Engine

Location : USA

Worldrigs ID: WR350

Model No : V-2000NG Drill Rig
Manufacturer : Versa Drill
Model Year : 2004
Condition : Used

Description :

2004 Vera Drill V-2000NG Drill Rig
Mounted On A 2003 Kimble Model C3300 6x6 Carrier Truck
Eaton 10 Speed Transmission
5,000 Hours
Fabco 23,000 Lb Front Axle
Spincer 46,000 Lb Rear Axles With Different Lock Out
3-Stage Jake Brake
250 Gallon Aluminum Fuel Tank
Aluminum Wheels
Aluminum Cab
Aluminum Diamond Plate Fenders
Cat C-16 600hp Diesel Engine
Ingersoll-Rand 1070cfm/350psi Air Compressor
80,000lb Pull Back/34,000lb Pull Down
3-Speed Top Head Drive
18,000 Lb Hydraulic Main Winch With Jib
2,000 Lb Auxiliary Winch With Jib
Automated Pipe Storage And Controlsystem
New Batteries
Good Rubber
All Wheel Drive
500' Of 2 7/8 X 4 1/2" Drill Pipe

Location : USA

Worldrigs ID: WR801
Description :

Mayhew 500 Drill Rig
Gardner Denver FXG172 5x6 Mud pump
7-1/2” rotary table (non-retractable)
18 ft Kelly
4 Jack
2 piston Bean water injection
18 Pipe of 15 ftX 31/4" x 2-3/8" MR Mathew reg drill pipe 270 ft total
Mounted on a Ford F700 Truck
Ford Diesel engine
10 speed transmission
449,042 Miles

Location : USA

Worldrigs ID: WR883
Description :

1981 Chicago Pneumatic T-700WH Deep Hole Drill Rig & Package
900/350 on-board air,
mounted on a tandem axle steer Kenworth carrier -75,000# pull-back,
4-rod carousel,
CAT 3406B deck engine recently replaced (less than 500 hours ago),
rebuilt dual top-head motors and planetaries,
rebuilt rotational pump and fan motor/pump,
new Nylotron head guides,
new winch line

Additional equipment included :
3,200ft 4 1/2"  x 30ft drill pipe with tandem axle drill pipe trailer
mounted IR tugger winch,
skid mounted Sullair 900/350 air compressor,
skid mounted 2000 gallon fuel tank,
skid mounted 300 bbl water tank,
skid mounted doghouse,
spare CAT 3406B engine (needs rebuilt),
6" hammer, 12" hammer/stabilizer combo,
12" tri-cone stabilizer,
casing lifters for both threaded and plain-end,
casing slips, break out wrench, J-wrench.

Location : USA

Worldrigs ID: WR785
Model : 250 Drill Rig
Manufacturer : Drillmax
Year : 2015
Condition : Used

Description :

2015 Drillmax 250 Well Drill Rig
One Owner
28ft Mast Tube with Lift Cylinder,
22ft of TopHead Stroke,
Heavy Duty Dual Motor TopHead,
4,000 FT/LBS Torque,
350 RPm,
Side Slide,
2" Swivel Assembly,
6,000 LB Winch with Hydraulic Jib Swing and Extend,
American 5X5 Mud Piston Pump with Variable Volume Output,
Suction Plumbing Below Deck,
Valve Handles for Mud and Air at Control Panel,
Development Air Compressor Package 100 CFM @ 175 PSI. Set Up to
Run at Same Time as Mud Pump,
2" ARO Diaphragm Pump for Grouting,
2" Plumbing to Mud System Including 2" Hardrock Swivel and Hinge Hoses,
12 Volt Electric Double Fan Cooling System,
Drill Pipe Single Rod Loader,
Drill Pipe Storage Rack for Up to 15 Pieces of Drill Pipe,
Hydraulic 24" Breakout Wrench,
3 Spool Helpers Controls to Operate Winch and Jib at Helper Station,
Table with 13" Opening and Breakout Fork to Fit 2-7/8" Drill Pipe,
Variable Control for Feed Pressure System,
4 - Hydraulic Leveling Jacks,
1 - Tool Try,
1 - 36" Tool Box,
Mud Flaps,
Mud Tub,
Mounted on a Dodge Ram 5500 Truck
4x4,
Cummins Diesel Engine,
6 speed transmission,
52 Gallon Fuel Tank,
Still in Use
Engine hours: Idle - 3,225 - (As of December 30, 2019)
Drive hours 378 - (As of December 30, 2019)
Mileage: 11,325 Miles, (As of December 30, 2019)

Location : USA

Worldrigs ID: WR780
Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago Pneumatic T650 Drill Rig
mounted on an IH Truck
All original parts
Head need work
Good Parts Machine

Location : USA

Worldrigs ID: WR83

Model : T64HB
Manufacturer : Schramm
Year : 1972
Condition : used

Description :

1972 Schramm T64HB drill rig
Detroit 8V71 Diesel Deck Engine
425 cfm / 250 psi Air Compressor
Water Injection Pump
Hammer Lubricator
200' ft of Drill Pipe (20' x 4-1/2") and basic tooling included
6" & 8" Hammers & Bits included
Lincoln 225 G7 Welder & Generator on board
Super Rapid Head Travel (loading pipe)
Mounted on a GMC truck
6V53 Diesel Engine
13 Speed Transmission
Flotation Tires (Front), Newer Front Brakes, Newer Transmission

Location : USA

Worldrigs ID: WR836
Description :

1977 Ingersoll-Rand TH60 Drill Rig
IR 600 cfm / 250 psi air compressor
Mission style magnum mud pump
Pipe Rack
Mounted on a 1977 International Paystar Truck
Detroit 8V71 Diesel Engine (Rebuilt in 2013-2014)
Hydraulic Leveling Jacks
Drill Pipe is not included (cost extra)

Location : USA

Worldrigs ID: WR691
Model : 1500 drill rig
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner Denver 1500 drill rig
5x6 mud pump
kelly drive recentlly rebuilt
Mounted on a twin axle carrier
Diesel engine
Note: no air compressor on board

Location : USA

Worldrigs ID: WR155

Model : T650 SL Drill Rig
Manufacturer : Reichdrill
Year : 1994
Condition : Used

Description :

1994 REICHdrill T-650 SL (Super Light) drill rig
Serial # 650TBGH00793
Cummins KT19 Diesel Deck Engine
900 CFM / 350 PSI Air Compressor
CAT Water Injection Pump
Hammer Lubricator
Mounted on a 1994 Ford L8000 Truck
Miles 64,899 on gauge
VIN #1FD7W82F7RVA26796
Cummins 7.3L Diesel Engine
Number of Axles4 & Drive Axles2

Location : USA

Worldrigs ID: WR833
Description :

2011 Atlas Copco RD20 Range III Drill Rig
Cummins KTAA19 (2019 Model) Diesel Deck Engine 800 Hours
IR HR2.5 1250 cfm / 350 psi Air Compressor
Mounted on CCC (Crane Carrier Company) Truck
Diesel Engine
Currently Working

Location : Middle East Region

Worldrigs ID: WR881
Description :

2003 Schramm T450 Crawler Drill Rig
Serial Number : J102-B236
Sullair 900 CFM / 350 PSI Air Compressor (serial number: 004-005820) - rated
1800 RPM
Caterpillar 3406B diesel deck engine
Hour meter shows 10,360 hours
Proheat Engine Heater
Bean FMC 2 Cylinder water injection pump
6 Rod Carousel
Graco Hammer Oiler
Pullback: 30,000 lb (13,608 kg)
16.5 inch table opening
Crawler mounted (note: can be mounted on a 2005 Kenworth double frame truck)

Location : USA

Worldrigs ID: WR853
Description :

Canterra CT-350 Drill Rig
Mounted on a 1989 Ford Truck
5-speed transmission with 2-speed rear
Diesel engine
Rod rack and plumbing for rotary option
Brand new hydraulic system installed in early 2019
(only 6 wells drilled in since)
Main line and sand line with free fall and spudder option
We would drive the wells in with a spudder option
Auger rack on the drivers side
Rod rack and tool box on the passenger side
Hydraulic Leveling Jacks

Location : USA

Worldrigs ID: WR146
Model : GXXTA D/D Back-In Well Service Rig
Manufacturer : Hopper
Condition : Used

Description :

Hopper GXXTA D/D Back-In Well Service Rig - S/N: 191
Detroit Series 60 Diesel Engine
Allison 5860 Transmission
15” Double Hydro Brake
Pemco 96’ ft H 180,000 lbs Mast
Hydraulic Raised & Scoped
Rod & Tubing Boards
Mounted on a CCC (Crane Carrier Company) 5-Axle Truck
Leveling Jacks
385/65R22.5 Front & 11R24.5 Rear Tires
Disc Wheels
Sold by "Bill of Sale" only
 

Location : USA