Description :
 

The RB 15 enables the user to drill with the following methods, with borehole
diameters 4” (108 mm) to 24” (609 mm):
 

Rotary-drilling with direct circulation
Rotary-drilling with reverse circulation Auger-drilling
 

Percussion core drilling (ram coring)
Wire-line core drilling 
Down-The-Hole hammer drilling (direct / reverse)
Free-fall drilling
Geothermal Drilling with DoubleRotation-Head
Inclined Drilling max.45 degrees
 

Additional rig components
Addit. to specifications overleaf
Foam pumpe
Line oiler (for DTH)
Free-fall winch
Hose winch
Percussion drilling device
Hydraulically driven Gen-set
Hydraulically driven welding-set
Rod handling arm
Rod box
 

Base carrier : Crawler base
 

Crawler width / Track shoe width : 2.450 / 500 mm
Transport dimensions L / W / H Diesel Engine (water-cooled) : 10.000 / 2.540 / 3.200 mm
Exhaust Emission Standard : EPA / Carb Tier 3, EU Stufe 3A
Rated output : 205 kW @ 2.200 U/min (rpm)
Diesel tank capacity : 280 l
Feed device (hydr. cylinder)
Push-down / Pull-back force : 70 / 140 kN
Feed speed : 0 - 0,8 m/s
 

Power swivel : L130
Gear select, 3 speeds
Torque at 0 - 34   rpm : 11.750 Nm
Torque at 0 - 100 rpm : 4.150 Nm
Torque at 0 - 320 rpm : 1.200 Nm
 

Chuck & break device : HSB 178.300
Clamping diameter max. / min. : 170 / 51 mm
Max. breaking torque : 41.000 Nm
 

Outrigger cylinder
Max. stroke : 600 mm
 

Mast head with hydr. swing-out device
Swing-out displacement : 700 mm
Swing-out force : 8 kN
 

Clamping device
Max. clearance diameter : 400 mm
Max. casing nominal diameter : DN 255
Max. clamping force : 300 kN

Winches
Main winch
Line pull 1st layer : 95 kN
Wire rope diameter / rope length : 20 / 130 m
Coring winch
Line pull 1st layer : 20 kN
Wire rope diameter / rope length : 8 / 300 m
Auxiliary / percussion winch
Line pull 1st layer : 26 kN
Wire rope diameter / rope length : 10 / 49 m

Pumps
Triplex piston pump
Discharge / Operating pressure : 270 l/min / 40 bar
Duplex piston pump
Discharge / Operating pressure : 450 l/min / 20 bar
Eccentric screw pump
Discharge / Operating pressure : 350 l/min / 24 bar
Centrifugal pump
Discharge capacity / Op.pressure : 1.500 l/min / 8 bar
Suction pump
Discharge capacity / Suction height : 5.300 l/min

Screw type compressor Compressor
Discharge / Operating pressure : 7 m³/min / 15 bar
Rotating casing table : VDT 324  VDT 419

Torque : 13 / 20 kNm  30 / 45 kNm

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig
425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on Ford Truck

Location : USA

Model : RD20 II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1993
Condition : Used

Description

1993 Ingersoll-Rand RD20 Range II Drill Rig - S/N: 3987
Cummins KTA19 Diesel Deck Deck Engine @ 600 HP
7 Rod Carusel
Cat 2520 water injection pump
Hammer Lubricator
Hydraulic Leveling Jacks
Mounted on a 1993 Central Manufacturing Truck with 4 axles
Cummins L10 Diesel Engine
VIN number: PGV84002
Note: No Air Compressor on board as of now (was a IR 1050/350)

Location : USA

Model : T64HB
Manufacturer : Schramm
Year : 1972
Condition : used

Description :

1972 Schramm T64HB drill rig
Detroit 8V71 Diesel Deck Engine
425 cfm / 250 psi Air Compressor
Water Injection Pump
Hammer Lubricator
200' ft of Drill Pipe (20' x 4-1/2") and basic tooling included
6" & 8" Hammers & Bits included
Lincoln 225 G7 Welder & Generator on board
Super Rapid Head Travel (loading pipe)
Mounted on a GMC truck
6V53 Diesel Engine
13 Speed Transmission
Flotation Tires (Front), Newer Front Brakes, Newer Transmission

Location : USA

Model : CME 75 Drill Rig
Manufacturer : CME Drill
Year : 1987
Condition : Used

Description :

1987 CME 75 Drill Rig
Has 3L6 Moyno Pump
Cat Head
2 Winches
4 Cylinder Gas Engine
The Rig Runs Good
Mounted on a 1988 Ford 750 Tandem Axle (Note: truck is in poor condition).
Also a brand new Auto Hammer in box that can be fitted on the drill

Location : USA

Description:

Model : T450GT Drill Rig
Manufacturer : Schramm
Year : 2008
Condition : Used

Description :

2008 Schramm T450GT Crawler Drill Rig
Caterpillar C-15 diesel engine @ 580 HP - S/N JRE09405
Sullair 1050 cfm / 350 psi air compressor with clutch
Floating sub
15 Rod Carousel - handles 3-1/2" Pipe
500' ft of 3-1/2" x 20' x 2-3/8" IF thread (estimated 50% condition)
Washington diverter
Hydraulic welder
Hammer lubricator
4 piston water injection pump
Rod spinner
2 motor power head
6,440 hours on gauge

Location : USA

Model : T450 Drill Rig
Manufacturer : Schramm
Year : 1988
Condition : Used

Description :

1988 Schramm T450 Drill Rig
Diesel Deck Engine
Air Compressor
Carousel
Centrifugal Pump
Pipe Rack
3 hydraulic leveling jacks
Mounted on a Truck
Diesel Engine

Location : USA

Model : CME 75 Drill Rig
Manufacturer : CME Drill
Year : 1987
Condition : Used

Description :

1987 CME 75 Drill Rig
Has 3L6 Moyno Pump
Cat Head
2 Winches
4 Cylinder Gas Engine
The Rig Runs Good
Mounted on a 1988 Ford 750 Tandem Axle (Note: truck is in poor condition).
Also a brand new Auto Hammer in box that can be fitted on the drill

Location : USA

SOLD

Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2004
Condition : Used

Description :

2004 Ingersoll-Rand T3W Drill Rig
Engine Hours: 20,621
50 ft – 45,000lb static hook load capacity
hydraulic raise/lower mast
Atlas Topco top drive
Braden 23,000 lb winch
mud system (5” x 6” or 5.5” x 8” GD mud pump)
hydraulic set up to run two pumps or air compressor
hydraulic hoses are re-conditioned
rig derrick can be shortened if requested

Note: no deck engine or air compressor on board the drill
Mounted on International 5600i Truck
Cummins ISX 14.9L Engine
475 Adv horsepower
engine brake
Eaton Fuller 18 speed manual transmission
330” wheel base
8 X 6 20,000lb front axle
54,000lb rears

Location : North America

Model : D40K Drill Rig
Manufacturer : Driltech
Condition : Used

Description :

Driltech D40K Drill Rig
50,000 lbs of pullback
high torque head
No carousels (removed for large diameter Well drilling)
dual winches 6000k single line
18000K single line hydraulic Denison P7 main pump - replaced early p-5
All pumps where rebuilt or replaced in 2015 including main gearbox rebuild
Replaced / upgraded to Mercedes tier 4 (I) 550hp diesel deck motor
900 CFM / 300 PSI air compressor
has a mud line and a true 3" mud swivel added to it so it's "mud ready"
New in 2015 radiator/engine cooler rated at 450hp Additional hydraulic cooler added
Mounted on 2012KW tier 4 435hp Paccar heavy spec truck
dual steering and full locking rears
Heavy duty engine Brake
Rig needs a few new hydraulic hoses and new paint job
Note: this machine is 100% California CARB compliant

Location : USA
 

Model : T7000 Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1981
Condition : Used

Description :

1981 Chicago Pneumatic T7000 Top Head Drive Rotary Drill Rig
S/N: S-81906 (The tag is missing)
Caterpiller 3406B diesel engine
GHH 825 cfm / 300 psi Air Compressor
40' ft mast (note: the mast, carousel & auxiliary winch with
jib have been removed and are stored at another location)

4-Hydraulic outriggers
Mounted on a FWD all-wheel drive CCC (Crane Carrier Chassis)
Cummins diesel engine
6-speed transmission
walking beam rear suspension
with fair size 16.5-22.5 front tires and fair size 11.00-20 rear tires
Showing 4,581 hour on the truck chassis

Note: No Rotary Head

Location : USA

SOLD
Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1994
Condition : Used

Description :

1994 Ingersoll-Rand T3W
CAT 3406C diesel deck engine (7,000 hours since rebuilt)
IR 825 cfm / 350 psi Air Compressor (4,300 hours since rebuilt)
8,000 lb rotary head
7 rod carousel
rod box
25 GPM Water Injection Pump
Hammer Lubricator
18,000 lb single line winch
Newer Tires
Newer Paint
Mounted on a Ford L9000 Truck
CAT 3176 diesel engine
Eaon 13 speed transmission
9,106 miles on odometer (may be incorrect)
Note: Rig was thoroughly reconditioned by manufacture in 2015 and has only been
used a few hours since

Location : USA

Model : T650 SL Drill Rig
Manufacturer : Reichdrill
Year : 1994
Condition : Used

Description :

1994 REICHdrill T-650 SL (Super Light) drill rig
Serial # 650TBGH00793
Cummins KT19 Diesel Deck Engine
900 CFM / 350 PSI Air Compressor
CAT Water Injection Pump
Hammer Lubricator
Mounted on a 1994 Ford L8000 Truck
Miles 64,899 on gauge
VIN #1FD7W82F7RVA26796
Cummins 7.3L Diesel Engine
Number of Axles4 & Drive Axles2

Location : USA

Description:

Engine: originally GMC Detroit Diesel, now has a Cummings 6BTA 5.9, Manufacture date of 10/26/1989

Model : T450GT Drill Rig
Manufacturer : Schramm
Year : 2008
Condition : Used

Description :

2008 Schramm T450GT Crawler Drill Rig
Caterpillar C-15 diesel engine @ 580 HP - S/N JRE09405
Sullair 1050 cfm / 350 psi air compressor with clutch
Floating sub
15 Rod Carousel - handles 3-1/2" Pipe
500' ft of 3-1/2" x 20' x 2-3/8" IF thread (estimated 50% condition)
Washington diverter
Hydraulic welder
Hammer lubricator
4 piston water injection pump
Rod spinner
2 motor power head
6,440 hours on gauge

Location : USA

Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used
Year : 1989

Description :
 
1989 Simco 2800 Drill Rig
Mounted on a 1989 F600 Truck with Diesel Engine
20' stroke in the tower (10000 lbs of thrust & 4000 lbs rotation)
Mission 2x3 mud pump
Sullair compressor
200' ft of simco pdg drill pipe
Mud Pan attached to the truck
 

Location : USA