Worldrigs ID: WR844
Description :

1994 Ingersoll-Rand T4W Drill Rig
Rebuilt 2006
Rebuilt Cummins KTA19C Diesel Deck Engine (rated 600 HP at 2100 RPM)
Rebuilt in 2006 a IRH2.5 1070 cfm / 350 psi air compressor
Mounted on a CCC (Crane Carrier)
Cummins L10 diesel engine
50,000 lbs of pullback
Setup for 2-7/8" IF Drill Pipe

The following work was performed when rebuilt:
Rebuild of rig and components
Remanufactured Cummins engine KTA19C 600 HP @ 2100 RPM from Cummins
(upgraded from original 545 HP @ 2100 RPM)
Remanufactured IR compressor HR2.5 1070 CFM @ 350 PSI
Rebuilt funk box Rebuilt or new hydraulic pumps and motor
Rebuilt hydraulic cylinder All new hydraulics and air hose
New and upgraded radiator
New and upgraded air compressor, oil cooler and hydraulic oil cooler
Valve spool rebuilt – new seals and control handles
New feed chains upper and lower – Upgraded
New front leaf springs on carrier
New gauges
New wire harness
Rig and all parts sandblasted and painted grey and red
Rig completely serviced – Ready to drill

Additional tooling :
6” IR QL60 Drive Hammer with Bit
6” IR QL60 Drill Hammer with 4-1/2” x 21.5ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 20ft lead steel with bit
4-1/2” X 25ft 2-7/8 API Drill Rod (11 pieces)
6” Casing Drive Plate
8” Casing Drive Plate
10” Casing Drive Plate
1 - Petol Chain Wrench set up for 4-1/2” Drill Rod and 6” Hammer
1 – Petol Chain Wrench set up for 6” Drill Rod and 8” Hammer
Lincoln Welder with Leads
Oxy/Acetalene Torch Setup

Location : Eastern Region

Worldrigs ID: WR774
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1995
Condition : Used

Description :

1995 Ingersoll-Rand T4W Drill Rig
IR 1000 cfm / 350 psi Air Compressor - (14,000 hours)
Cummins QSK Diesel Deck Engine - rated 600 HP & 2100 RPM - (Reman
as of March 2016 with 1,971 hours on meter as of 8-6-2019)
50,000 lbs of pullback
Worm Gear Power Head
Water Injection Pump
Hammer Lubricator
7 & 4 Rod Carousel
Starting Aid Diesel Fired Pre-heater with Ether
Hydraulic Leveling Jacks
Mounted on a CCC (Crane Carrier Company) Truck
Caterpillar 3306 C diesel engine
mileage 75,000

Location : USA

Worldrigs ID: WR696
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1974
Condition : Used

Description :

1974 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine (inframe rebuilt)
IR HP 750 CFM / 250 Air Compressor
Water Injection Pump
Oil Injection Pump
Two Winch Lines
Carousel
36” Mast (Autofeed)
Pull Down & Pull Back
18” Table Opening
Worm Gear Top Head
Hydraulic Cooler
Rod Changer
Handles 4-½” x 25ft Drill Pipe
3 Outriggers
Complete Part & Service / Repair Manual
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Slow & Fast Rotation
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine

Location : USA

Worldrigs ID: WR791
Components :

1. The three section pressure compensated load sensed Sauer Danfoss
hydraulic piston pumps are directly coupled to the 6LTAA8.9-360 Cummins
diesel engine via a high quality German drive plate and coupling.

2. The drill mast is a lattice type. The feed system uses a single hydraulic cylinder
connected to a 2:1sheave system connected to heavy duty leaf chains giving
approximately 25,000kg of extraction force with a 6.7 metre stroke.

3. Adjustable hydraulic pressure knob to control and limit the down force
on the feed so the rig base will not be raised up whilst drilling.

4. Adjustable flow control valve to control the speed in which the drill bit advances.

5. Pressure gauges on control panel for calculating either rotation torque or feed pressure.

6. Directional control valves and tilt cylinder with over centre valve and flow limiters

7. A single bent axis piston hydraulic motor coupled to a 4 speed gearbox on the
rotation gearbox.

8. A 400 litre hydraulic oil tank with sight gauge, breather cap, internal suction
screens and 10 micron filter on the return line.

9. 4 x 30,000# support jacks, which are adjustable to level the rig in uneven terrain
and to stabilize the rig.

10. 10” x 7 1⁄2” Duplex type piston mud pump driven by Sauer Danfoss hydraulic Gerola Motor.

11. 8000kg single line pull haul winch.

12. Large Air/Oil fan type oil cooler driven by a hydraulic motor with overrun protection.

13. High quality Cetop type solenoid valves to change between different hydraulic functions.

14. Breakout wrench

15. Rod loading system. (optional)

Worldrigs ID: WR807
Model : Larson Reverse Rotary Drill Rig - Air Assited
Manufacturer : Generic
Condition : Used

Description :

1982 Larson Air Assisted Reverse Rotary Drill Rig with Substructure
New derrick 120,000 lbs rated
rebult hydraulic system in 2010
Caterpillar 6 cylinder deck engine (spare rebuilt engine in a crate)
double draw works
1" main line, 1" laydown line, 1/2" tail out line

Included as a Package:
Doghouse - Wired, lighted, AC, tool room, Geolograph
40ft 5th wheel, tandem wheel, drill pipe trailer
Substructure 15ft X 12ft 8ft Custom fabricated with guard rails
1,500  ft of 6-5/8" ID IF modified
90ft of 14" drill collars
2010 Atlas Copco 950 cfm / 350 psi SRVS1000 CD6 Air Compressor
1,000 gallon fuel storage tank with transfer pump
King swivel
Pilot Hole bits
Reaming Hole oppener bits
Casing Collars

Optional Equipment that Cost Extra:
Complete testing pump equipment, 6 pumps, 800 ft of 10x3.5x2.437" column
tube she, gear head, discharge head
12 Cylinder Caterpillar test engine

Location : USA

Worldrigs ID: WR863
Description :

1977 Chicago-Pneumatic 7000 Top Head Drive Rotary Drill Rig - S/N: 97328
Cat 3406-A diesel deck engine
GHH 825-300 air compressor
43 ft hydraulic raise mast
7" diameter 70,000 lbs hydraulic pull back and pull down hydraulic cylinders
8,000 lbs hydraulic winch and hydraulic jib
hydraulic break-out wrench
carousel
table bushings
fold up rear platform
3-hydraulic outriggers
120-volt work lights
Mounted on a 1975 Mack DM600 Truck tandem axle chassis - VIN# DM492S1239
Mack 300 diesel engine
Mack 6 speed lo-hole transmission
equipped with Jacobs engine brake
Mack camelback spring suspension
216" wheelbase
445/65 22.5 front and 11.00-20 rear tires
In fair to good condition
Upper Meter Reads 4,441 Hours & Odometer Reads 60,157 Miles

Location : USA

Worldrigs ID: WR779
Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : As-Is

Description :

Chicago Pneumatic T650 Drill Rig
Mounted on a 6 x 6 Oshkosh Truck
Modified drill rig
Direct drive off of the truck engine
900 cfm / 350 psi air compressor

Location : USA

Worldrigs ID: WR869
Description :

1972 Chicago Pneumatic 650 Drill Rig
Sullair 750/250 air compressor (verifying the size & model)
Caterpillar 3306 Diesel Deck Engine
Gardner Denver 5x6 air driven mud pump
Hydraulic slide pipe rack
Winch
Mounted on a Ford 900 Truck (VIN #: T91KVN93939)
Caterpillar 3208 Diesel Engine
Bobcat welder

Location : USA

Worldrigs ID: WR765
Model : 1250 Drill Rig
Manufacturer : Failing
Condition : Used

Description :

Failing 1250 Drill Rig
Mounted on a Ford Truck
Diesel Engine
5x6 Duplex Mud Pump
Table Drive & Break out wrench
Pipe Rack
300 ft of drill pipe

Location : USA

Worldrigs ID: WR877
Description :

2015 Atlas Copco Pit Viper 235 Drill
Pressure: 350 psi
Flow: 1.450 cfm
Approx 11.000 Working Hours

Location : South America

Worldrigs ID: WR790
Model : 500 Drill Rig
Manufacturer : Midway
Year : 1969
Condition : Used

Description :

1969 Midway 500 Drill Rig
Mounted on 1969 Peterbilt Truck
Leroi 100S Air Compressor
Gardner-Denver 5x6 Duplex Piston Mud Pump
New Rear Jacks
Recent Cummins Swap
Transfer case rebuilt in summer 2018
Comes with 200 ft. of 2-7/8” drill pipe
Currently working
Ready to drill

Location : USA

Worldrigs ID: WR787
Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used

Description :

Simco 2800 Auger Drill - Unmounted
Year: 1976 / 1977
Dual Motor Hydraulic Top Rotary Power Head (swings away)
11 ft. 6 in. mast (retracted), approximately 18 ft. mast extended
Cathead
Winch
Wisconsin 4 cylindergas motor
In working order
Currently unmounted but comes with trailer it was previously mounted on
included in deal

Location : USA

Worldrigs ID: WR867
Description :

1980 Ingersoll-Rand TH60 Drill Rig - 0428
Ingersoll-Rand 750 cfm / 250 psi Air Compressor
Bean Triplex Water Injectior Pump
420 ft of (3-1/2" x 20) Drill Pipe
2 Used Hammers & Bits, Slips and Tooling included
10 Rod Carousel
18,000 lbs Winch
Pipe Rack
Hydraulic leveling jacks
Mounted on a 1978 International Harvestor F-5070 Truck
Detroit 8V92 Diesel Engine

Note: Rig is operational but needs a few repairs

Location : USA

Worldrigs ID: WR685
Model : B56 Drill Rig
Manufacturer : Mobile
Year : 1970
Condition : Used

Description :

1970 Mobile B56 Drill Rig
Diesel Engine on deck
3L6 Moyno water pump
Cathead
Mounted on 1993 International truck
p/b diesel engine

Location : USA

Worldrigs ID: WR799
Model : T4W LT Range II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2005
Condition : Used

Description :

Ingersoll-Rand T4W LT (Long Tower) Range II Drill Rig
2005 CAT C-12 Diesel Engine (4,000 hours)
Ingersoll-Rand 1170 cfm / 350 psi Air Compressor
70,000 lbs of Pullback (Deep Hole)
4 hole gearbox and 2 hole gearbox
High Torque Spur Gear power head with cushion sub
Bean Water Injector Pump rated at 2000 psi
Mounted on a CCC (Craine Carrier Company)
CAT 3406 Diesel Engine
2400 Gal Fuel Tank with Hose Reels
12V Electric Pump

Mounted on a 32 ft Tandum Axle trailer
Sullair 1150 cfm / 350 psi Air Compressor
CAT C-15 Diesel Engine with 7,000 hours

Hurricane Booster - rated 900 lbs of pressure
CAT 3126 Diesel Engine
Both mounted on a 32' ft Tandum Axle Trailer

120 Pipe of T4 style drill pipe (3,000 ft) 3-1/2" Reg Pin and Box
5 check valve subadapters
Pipe and adapters are all loaded on 2 tandum axle flat bed trailers
Drill Rig Base or Platform
14" tall 35 ft long 10 ft wide with folding ramps and fold down walkways
38 ft tandum axle trailer with roller for moving
IR-120 Hammer with 12-1/4" bit x 11" x 20 Stabilizer
IR-TD-90 Hammer with 8-7/8" bit x 8" x 20 Stabilizer
IR QLX-60 Hammer w/ 6-1/4"bit, 6" by 25ft Stabilizer
3 sets of Casing Clamp type Elevators for 4-1/2", 7" & 9-5/8"
Washington rotation head diverter assembly with adaptter plates
35 ft of blow pipe with hammer unions
2 complete Petol wrenches, Misc Table bushings & Wrenches Forks and Subs

Location : USA

Worldrigs ID: WR758
Model : T130 Drill Rig - Range III Telescoping Mast
Manufacturer : Schramm
Year : 2004
Condition : Used

Description :

2004 Schramm T130 drill rig - Range III Telescoping Mast - S/N: J130-0110
Substtructure, Rig Floor, Hand Rails, Center Cat Walk
MTU V12-2000TA DDEC Diesel Deck Engine - rated @ 760 HP
Hammer Oilier
130,000 lbs. (59,090 kg) of Pullback
28" inch (711 mm) table opening
50 feet (15.25 m) of clear head travel
3-in ID spindle with optional 5.25-in spindle
Mounted on a CCC (Crane Carrier Company) Truck
VIN# 1CYDGD5874T046284
CAT C12 Diesel Engine - Rated @ 410 HP
Note: New Complete Paint Job finished in May 2013 by EWD with many wells
drilled since
Also available at an extra cost: Dog House, 6000 ft of 4-1/2" IR style drill
pipe, and 1 pipe trailers. (Cost Extra)

Location : USA

Worldrigs ID: WR540

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig
425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on Ford Truck

Location : USA

Worldrigs ID: WR836
Description :

1977 Ingersoll-Rand TH60 Drill Rig
IR 600 cfm / 250 psi air compressor
Mission style magnum mud pump
Pipe Rack
Mounted on a 1977 International Paystar Truck
Detroit 8V71 Diesel Engine (Rebuilt in 2013-2014)
Hydraulic Leveling Jacks
Drill Pipe is not included (cost extra)

Location : USA

Worldrigs ID: WR202

Model : CTM 10,000 Drill Rig
Manufacturer : DeepRock
Year : 1986
Condition : Used

Description :

Deep Rock CTM 10,000 Drill Rig Package

Package Includes:

Deep Rock CTM 10,000 Commercial Water Well Drilling Rig (Trailer Mounted with Single Axle)
Honda 23 HP engine
Hydraulic Driven
Mission 2 x 1-1/2 Mud Pump
Hydraulic Breakout Wrench
Electric Jib Wrench
Mud Pit
Trailer Mounted

Accessories Include:
2-3/8 x 2-3/8 FMxFM subs
2-3/8 x 3-1/2 FMxFM subs
Drag Bits, 3-1/2 to 6 inch
Tri-Cone Bits, 3-1/2 to 6-1/8 inch
4 inch DTH hammer with 4-1/4 inch Bit
4 inch Shock Absorber sub for D.T.H.
Approximately 200 ft. Drill Rod
Good for drilling shallow Screen Wells & DTH Rock drilling to 150 - 200' ft deep

Included as a Package:

Ingersoll-Rand Gyro-Flo Air Compressor
600 CFM / 100 PSI
Powered by Detroit 671 Diesel Engine
Mounted on a 1974 GMC 6500 Truck
366 Gas Engine (rebuilt with less than 10,000 miles)
Allison 4 speed Transmission
Air Brakes
 
Location : USA

Worldrigs ID: WR492
Speedstar S S61A Cable Tool Rig Details:

Worldrigs ID: WR878
Description :

Davey Rouselle M8A Drill Rig
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Within the last 2 years the drill has had the air compressor "gone through"
Has had the table replaced
Ramsey pulldown winch replaced
Chain cases replaced
Table transmission rebuilt
New radiator for deck engine
Various other small repairs done
Deck engine needs repaired or replaced
Comes with 100ft of 4.5”x 30ft Kelly and 4” Davey rods
Davey Changeover sub to 3.5 API threads for bit - with wrenchs and slips
Mounted on 1991 Sterling truck
Truck Runs fine but 4th gear does jump out
Truck has a 3306 cat motor in it and an 8 speed transmission
Tires are in good shape.
Drill motor is getting weak and will need rebuilt - Can be replaced for an extra cost
Lots of repairs and rebuilds in the last 2 years.

Location : USA

Worldrigs ID: WR595
Model : T64HB Drill Rig
Manufacturer : Schramm
Year : N/A
Condition : Used

Description :

Schramm T64HB Drill Rig
Detroit 8V92T Diesel Deck Engine
GHH 750 cfm / 300 psi Air Compressor
Myers 10gpm Water Injection Pump
Pipe Rack
3 Hydraulic Leveling Jacks
Mounted on a 1998 International truck
Cummins M11 diesel engine and jake brakes
New tire all around
Included as a Package or Cost Extra:
Used - 300' ft of Drill Pipe (20' x 4-1/2") and basic tooling
Used – (2) 6" Mission Hammers & 8” Stabilizer

Location : USA

Worldrigs ID: WR852
Description :

1989 Schramm T-660 Drill Rig
Detroit 8V92 Diesel Deck Engine (less than 4000 hours since
complete rebuild with preheater)
GHH 900 cfm / 350 psi Air Compressor (Rebuilt, less than 500 hours,
with clutch)
Jib-Boom
Bean water injection pump
360 ft of drill pipe (20ft x 4-1/2"), table bushings & basic tooling included
7 Rod Carousel Lazy Susan
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a GMC White Brigadier Truck (60k+ miles on gauge)
Cat 3208 (Rebuilt transmission less than 2000 miles ago)
Very good tires
Note: Replaced upper chains when the motor were rebuilt about 3500 hours ago

Current repairs needed we are aware of:
Truck CAT 3208 engine starts very hard but once it starts then it runs fine and
runs good (Rebuild time approaching soon)
Traverse cylinders leak small amounts of oil
Deck deck engine leaks small amounts of oil
Compressor clutch work manually only

Location : USA

Worldrigs ID: WR861
Description :

Schramm T130 Drill Rig
Diesel Deck Engine
Mounted on a CCC Truck
Diesel Engine

Included as a package:
4-1/2" Bottle Neck X Hole Drill Pipe
6" Collars = 90 ft
All Subs needed to drill
Spare Motor
Spare Parts : Top Drive (Rebuilt no hours), New Spindle,
Bearings for top drive, Chive Crown
Pipe Racks with Catwalk (30 ft L X 5 ft W X 3-1/2 ft T)

Location : USA

Worldrigs ID: WR831
Description :

1996 Speedstar SD300 Drill Rig
Mounted on an 1995 International Truck
Cummins N14 Diesel Engine
10 Speed transmission
Sullair 750 cfm / 350 psi air compressor with clutch
Gardner Denver 5x6 Duplex Mud Pump (hydraulic driven)
Pipe rack
Hydraulic Leveling Jacks

Location : USA

Worldrigs ID: WR665
Model : 10TG Drill Rig
Manufacturer : PortaDrill
Year : 1969
Condition : Used

Description :

1969 Portadrill 10TG Drill Rig
Detroit 6V71 diesel deck engine with less than 50 hours
International 501 carrier engine
Atlas Copco 600 cfm / 125 psi air compressor
35ft tubular mast rated at 65k
Rebuilt swivel
21ft x 4-1/2" fluted Kelly
7-1/2" rotary table
4 line blocks
Hydrolic leveling jacks
Triple drum draw works
Hydrolic pulldown
Soap injection pump
100 ft of 4-1/2" drill pipe included
Auxiliary hydrolic connections
New Paint job completed September 2018

Location : USA

Worldrigs ID: WR773
Model : T64HB Drill Rig - Retrofitted
Manufacturer : Schramm
Year : 1978
Condition : Used

Description :

1978 Schramm T64HB Drill Rig - Retrofitted in year 2000
Detroit 8V92 diesel deck engine
T660 Derrick replaced the T64HB Derrick
Sullair 900 cfm / 350 psi Air Compressor
Carousel
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a 1986 Ford L8000 Truck
CAT 3208 diesel engine
13 speed Eaton fuller transmission

Location : USA

Worldrigs ID: WR810
Model : 1000 Drill Rig & Package
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner-Denver 1000 Drill Rig
14W Drawworks
7-1/2" Rotary Table
Rated for drilling to 1000 ft
Dis-assembled for rebuild
Deck steel replaced in preparation for rebuild
Comes with all components necessary to rebuild back to original specs:
2-stage mast cylinder
3- large 8-1/2 ft outriggers
Piston style WX 1004 compressor (stored inside building)
Gardner-Denver FXG 5x6 mud pump (stored inside building)
24 ft 3-3/8" fluted kelly bar
Little Giant Swivel
Mayhew block for 1000 rig 12" single sheave
292 ft of 3-1/2" flush drill pipe

- 16 ft skid for set up for Gardner Denver 5x8 mud pump, Detroit 353 Diesel
- Engine with Rockford clutch (1600 hours), with 150 gallon fuel tank
- GMC 6-71 Power Unit with Rockford clutch, Rotary table slips, Blue Demon
- Drag Bit 5, spools of cables, assorted bit breakers, 2" relief valve, pipe clamps
and pick up heads, compression coupling and 4" valve, steel mud tank
- 2-3/8" IF to 3-1/2" Reg pipe to bit tubs, pipe spider rings, Rotary Table
- Drill Up slips, shop built collars, T-Pipe for starter, cross over sub adapters, Tool
holder for pipe in table, Petol chain wrenches, regular chain wrenches, Set of
banded v-belts for mud pump skid, 2 rods for GD gear end, bull gear and
eccentric, 2 pairs of sleeves for GD 5x8, valves caps for GD 5x6, cylinder head
for GD 5x6, safe guard and Dodge gear boxes for mud pumps, pinion gear for GD
5x8 duplex 90%, new electric motors 1/2 HP - 3/4 HP - 1 HP stub shaft, power
tower for Keystone Gardner Denver, miscellaneous bits
- 1973 Ford 8000 truck
- Caterpillar 3116 diesel engine
- 10-speedRoadranger transmission

Location : USA

Worldrigs ID: WR828
Description :

1991 Reichdrill T-650-W Drill Rig
Camion has been repainted
Drill Rig sandblasted
Brakes and boosters has been change
Feed Cylinder redone
Deck engine good
Compressor turns
1300 working hours
Needs some work

Location : North America

Worldrigs ID: WR779
Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : As-Is

Description :

Chicago Pneumatic T650 Drill Rig
Mounted on a 6 x 6 Oshkosh Truck
Modified drill rig
Direct drive off of the truck engine
900 cfm / 350 psi air compressor

Location : USA

Worldrigs ID: WR839
Description :

LTD 360 Cable Drill Rig
Carries enough mainline cable to drill to a depth of 450 feet
Bore diameters of 4" to 10" inches
Lift capability of 8,000 lbs for casing removal
40 gallons of on-board water storage with a 40 PSI pump
150 amp arc welder when steel casing is used
20 gallons of fuel (enough to drill about 75 feet)
Rated - Penetration rates usually range between 2-½-5 feet per hour
depending on the geology/ground formations with drilling conditions
Mounted on a 2 axles trailer

Location : USA

Worldrigs ID: WR790
Model : 500 Drill Rig
Manufacturer : Midway
Year : 1969
Condition : Used

Description :

1969 Midway 500 Drill Rig
Mounted on 1969 Peterbilt Truck
Leroi 100S Air Compressor
Gardner-Denver 5x6 Duplex Piston Mud Pump
New Rear Jacks
Recent Cummins Swap
Transfer case rebuilt in summer 2018
Comes with 200 ft. of 2-7/8” drill pipe
Currently working
Ready to drill

Location : USA

Worldrigs ID: WR628
Model : T64HB Drill Rig
Manufacturer : Schramm
Year : 1969
Condition : Used

Description :

1969 Schramm T64 Drill Rig
Detroit 8V71 diesel deck engine
425 cfm / 250 psi air compressor
300 ft of 4-½inches x 20ft drill pipe
6inches hammer w/ 6inches bit
8inches hammer w/ 8inches bit
2 new motors on head
Last had it running in mid-January 2019
Mounted on a newer 1995 Ford 9000 Truck
Cummins N14 diesel engine
9-speed transmission
2250 tires (estimated 85% good)

Location : USA

Worldrigs ID: WR758
Model : T130 Drill Rig - Range III Telescoping Mast
Manufacturer : Schramm
Year : 2004
Condition : Used

Description :

2004 Schramm T130 drill rig - Range III Telescoping Mast - S/N: J130-0110
Substtructure, Rig Floor, Hand Rails, Center Cat Walk
MTU V12-2000TA DDEC Diesel Deck Engine - rated @ 760 HP
Hammer Oilier
130,000 lbs. (59,090 kg) of Pullback
28" inch (711 mm) table opening
50 feet (15.25 m) of clear head travel
3-in ID spindle with optional 5.25-in spindle
Mounted on a CCC (Crane Carrier Company) Truck
VIN# 1CYDGD5874T046284
CAT C12 Diesel Engine - Rated @ 410 HP
Note: New Complete Paint Job finished in May 2013 by EWD with many wells
drilled since
Also available at an extra cost: Dog House, 6000 ft of 4-1/2" IR style drill
pipe, and 1 pipe trailers. (Cost Extra)

Location : USA

Worldrigs ID: WR767
Model : M8 Drill Rig
Manufacturer : Davey
Condition : Used

Description :

Davey M8 Table Drive Water Well Drill Rig
500 CFM Air Compressor
In working order
With spare tower & parts

Location : USA

Worldrigs ID: WR705
Model : T625 Drill Rig
Manufacturer : Reichdrill
Year : 1994
Condition : Used

Description :

1994 Reichdrill T625 Drill Rig
Sullair 900 cfm / 350 air compressor (Rebuilt in 2016)
Cummins 855 NTA Diesel Deck Engine (Rebuilt in 2017)
- rated 435 HP at 1800 RPM - S/N: 34071 & CPL: 1576
Bean Water Injection Pump 7 GPM
Hammer Lubricator
28,000 lbs of Pullback
4,000 lbs/ft of torque
6 Rod Carousel
700 ft of used drill pipe (20 ft x 4-1/2" x 2-7/8") & basic tooling included
Hydraulic Leveling Jacks
Mounted on a 1995 Ford LTN 8000 Truck
Diesel Engine - rated 300 HP (reman replaced old engine)
37,000+- miles
Note: Radiators was tested and repaired as needed & New table in 2018
37 ft L x 8 ft 6" W x 12 ft 6" H and 52,500 lbs weight

Location : USA

Worldrigs ID: WR848
Description :

1997 IMT AF18 Crawler Drill Rig
12,000 hours (+/-) on the rig
Cummins QSL9 Diesel Engine (Tier III & recently installed - only 4,500 hours+/-)

Location : USA

Worldrigs ID: WR756
Model : V-1040DP Drill Rig
Manufacturer : Versa Drill
Year : 2010
Condition : Used

Description :

2010 Versa Drill V-1040DP Drill Rig
Caterpillar C15 Diesel Engine (Tier III - S/N: JRE11211) - rated
540 HP & 2100 RPM
IR 1070 cfm / 350 psi Air compressor (Clutch)
6500+ Hours on gauge
40,000 lbs of pullback
Hammer Lubricator 7 Gallon
Bean 4 piston bean water injection 25 GPM
Main Winch 18k & Secondary 2k
Pipe rack holds 18 pipe
4 stabilizing Jack
Mounted on a 2010 Peterbilt 367 Truck
Cummins ISX 15 Diesel Engine (Tier III - S/N: 1040039) - rated
565 HP (Heater) with 31,000+ Miles on gauge
Eaton Fuller 13 Speed LL Transmission
Jake Brakes
22,000 lb. front axle, 46,000 lb. rear tandem axles with driver
controlled main locking differentials, total 68,000 GVW
Total Weight 55,520 lbs = Front Axle: 15,620 lbs &
Rear Axle: 39,560 lbs

Location : USA

Worldrigs ID: WR596
Model : D40K Drill Rig
Manufacturer : Driltech
Year : 1974
Condition : Used

Description :

1974 Driltech D40K Drill Rig
CAT Diesel Deck Engine - rated 425 HP
Sullair 750 cfm / 150 psi air compressor
25’ ft inner & outer Carousels
8000 lb main/jib
Gardner Denver 5x6” Duplex Mud pump (variable hydraulics)
20 GPM water injection pump
Rebuilt hydraulic pumps & splitter
Hot box
good tires
Mounted on a CCC (Crane Carrier Company) Truck
466 diesel engine
Extra: 275’ ft of (25’ x 4-1/2” x 2-7/8 IF Rods)
23’ ft surface collar & mud pit

Location : USA

Worldrigs ID: WR661
Model : RD20 III Drill Rig
Manufacturer : Atlas Copco
Year : 2007
Condition : Used

Description :

2007 Atlas Copco RD20 - Range III Drill Rig
120,000 lbs of pullback
Cummins QSK19 Diesel Deck Engine (Very Low Hours)
IR HR2.5 1250 cfm / 350 psi Air Compressor with In/Out box
Rotary Head: 4SV-2-10 Spur gear
Top drive head assembly rated to 8,000 ft. lbs. torque
Single Rod Loader for handling 4.5” o.d. X 30ft long drill rods
Spindle Sub – (4 1/2” x 2 7/8IF")
Water Injection Pump
Hammer Lubricator
Mounted on a CCC (Crane Carrier Carrier) Truck
CAT C13 Diesel Engine

Tooling & Pipe included:
51 (4-1/2 X 30ft X 2-7/8IF") Thread Drill Pipe
12 - (6” X 30ft) Slick Drill Collars
3 - (8” X 30ft) Spiral Drill Collars
Basic Tooling
23 Subs on Steel Platform on Pins

Location : USA

Worldrigs ID: WR866
Description :

Davey Rouselle M8A Drill Rig
Mounted on a 1991 Sterling truck
CAT 3306 Diesel Engine
8 speed transmission
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Included with 100 ft of Davey rods and a changeover sub to 3.5" API threads for bit

Note: Since 2018 the drill has had the air compressor "gone through", has had
the table replaced, Ramsey pulldown winch replaced, chain cases replaced,
table transmission rebuilt, new radiator for deck engine, and various other
small repairs done
Drill motor is getting weak and will need rebuilt and can be done here if needed
and the price would reflect that
Truck Runs fine but 4th gear does jump out

Location : USA

Worldrigs ID: WR859
Description :

1978 Portadrill 524-3A Drill Rig
Gardner-Denver 5-1/2" Mud Pump
Leroi 256 S-2 250 PSI Air Compressor
Hydrostatic drawworks and rotary table
Pipe Slide
Injection pump
Hydraulic leveling jacks
Mounted on a 1999 Ford Louisville truck
Powered by Cummins Red Top N14 Diesel Engine - rated 500 HP
Tag axle

Location : USA

Worldrigs ID: WR603
Model : 3000 Drill Rig
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner Denver 3000 Trailer Mounted Drill Rig
Set up for RC
Brewster 18" removable Table
Single draw works
7 Part Main block
2 Cat heads
New Hydraulic pump system
New Hydraulic winch for Tail out
International DT466 Diesel engine
Trailer mounted
6 Leveling jacks
Hydraulic tower ram
Dog House-- Optional at extra cost
The rig is 12’ 6” tall when connected to a day cab tractor. The width is 8’

Location : USA

Worldrigs ID: WR832
Description :

2016 Gefco 30K Drill Rig
5,100+ Hours
Mounted on a Peterbuilt 367 6x4 Truck
Cummins rated 550 HP ISX diesel engine (Tier IV)
Sullair 1000 cfm / 350 psi air compressor
Enclosed steel gear box PTO
4 hydraulic leveling jacks
Rotary tophead
6 rod carosel (removed but included in the sale)
15 rod pipe rack
18 gpm Bean water pump
Power sliding holding wrench and table
60” breakout wrench
Pipe spinner
DTH lubricator
Remote controlled jib boom
Moyno 3L8 pump mounted on deck

Location : USA

Worldrigs ID: WR803
Model : 2000 Drill Rig & Package
Manufacturer : Gardner Denver
Year : 1978
Condition : Used

Description :

1978 Gardner Denver 2000 Drill Rig
Mounted on a Truck with 2 axles
Cummins 400 Big Cam Diesel Engine
18" GD rotary table (New Seals)
(2) six line blocks with 120,000 lbs hookload/pullback
Newer cables on kelly and pulling lines
2 cat heads
Hydraulic sand line
With hydro brake set up
Gardner Denver 6x10 mud pump with matco quick change fluid end
New 3" kelly hose high pressure
37 ft square kelly
 
Set up to drill 1600 ft - 2,200 ft water wells
Price Reduced to Sell Fast in July 2020

Included as Package:
1000 ft of 4-1/2" drill pipe
210 ft of 6" drill collars
misc. tooling
pipe truck and trailer

Location : USA

Worldrigs ID: WR560

Model : T130 Drill Rig
Manufacturer : Schramm
Model Year : 2003
Condition : Used

Description

2003 Schramm T130 Drill Rig - S/N: J130-0707
Detroit DDC/MTU V12-2000TA DDEC Diesel Deck Engine
Mast: Telescoping construction permits long head travel 50’' ft
Note: Shorter length in transport position
130,000 lbs of Pullback
Free standing design with 28"” table opening
Sullair 1350 cfm / 350 psi Air Compressor (Rebuilt with low hours)
Hydraulic pumps (low hours since rebuilt)
Top Head: Fixed position - two hydraulic motors. 0-143 RPM with 106,600 in-lb of torque
Pipe handling sling
Set up for RD20 style (4-½”" X 30'’ X 2-7/8" IF) Drill Pipe
Carousel
Cat Water Injection Pump
Graco Hammer Lubricator
Mounted on a CCC (Crane Carrier Company) Truck - VIN#: 1CYDGD5843T046189
CAT diesel engine
425/65R22.5 front tires 12R22.5 rear tires
Sub Base: 9'’ wide 40'’ long and 3’' tall & Basic Tooling Included

Location : USA

Worldrigs ID: WR707
Model : 275 Drill Rig
Manufacturer : Speedstar
Year : 1989
Condition : Used

Description :

1989 Speedstar 275 Drill Rig
PTO drive
The rig runs 20ft rods
Holds 340ft of 2-7/8 Mayhew Regular in the rack
600ft of fairly new rods included
Note: No rod loader, no carousel, no hammer oilier, no bean pump
The rig currently has a non-operational joy twist air
Mounted on a 1988 International truck - All Wheel Drive
Sandline possibly its a 2500lb
Has a new Braden 12k main winch from Gefco
5x6 Gardner Denver Mud pump - Completely rebuilt including all components
in the gear end & shafts.
New Hubcity 3h gearbox to drive mud pump from Gefco
Both top head motors are new (originals as a backup)
Top head has been completely rebuilt (New spindle shaft and components
from Gefco)
New paint job with Emron aircraft paint. Truck was completely sandblasted and
taken down to bare metal and brought back to its current condition. (Pictures
available documenting the work).
It is a Speedstar 275 which is almost identical to the quickdrill 275 but it
is a newer version and has some features that the quickdrills dont have.

Location : USA

Worldrigs ID: WR454

Model : RD20 II Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1993
Condition : Used

Description

1993 Ingersoll-Rand RD20 Range II Drill Rig - S/N: 3987
Cummins KTA19 Diesel Deck Deck Engine @ 600 HP
7 Rod Carusel
Cat 2520 water injection pump
Hammer Lubricator
Hydraulic Leveling Jacks
Mounted on a 1993 Central Manufacturing Truck with 4 axles
Cummins L10 Diesel Engine
VIN number: PGV84002
Note: No Air Compressor on board as of now (was a IR 1050/350)

Location : USA

Worldrigs ID: WR804
Model : 2500 Drill Rig
Manufacturer : Gardner Denver
Year : 1985
Condition : Used

Description :

1985 Gardner Denver 2500 Drill Rig
Cummins - rated 400 HP
three speed Allison (750) auto transmission
Diesel tank on rig
100 ton McKissich (shorty) blocks with 7/8” cable
Weight indicator
4 hydraulic leveling jacks
Tongs
Hydraulic raise and cable telescoping 67 ft mast
Mounted on a 2 axle trailer
130,000 lbs. mast
18” Gardner Denver rotary table
Tongs with air cathead make up and air cathead breakout
1 – Swivel
1 – 40ft x 3-½” IF Kelly with bushing
Rat hole digger
Rat hole shuck

Location : USA

Worldrigs ID: WR153

Model : 3000-CF Drill Rig
Manufacturer : Failing
Condition : Used

Description :

Failing / Gefco Holemaster 3000-CF Drill Rig
Factory Rated Capacity: 3,700 ft. depth using 3-1/2” drill pipe.
Mast: Cold drawn street tubing, elec. Welded, 3-sect. with 3-way taper on top sect.
Hydraulically raised & lowered. Wired for elec. Lights. Equipped w/retracting
channel swivel guides for reverse circulation swivel. Equipped with ladder,
climber’s safety device.
 

Hgt. 72” Telescoping, Width 86” center to center of mast legs, Depth 48” center
to center of mast legs, Capacity total gross 133,000 lbs. hook load 100,000 lbs.
Racking board capacity 3,000 ft. of 3-1/2” drill pipe, may be mounted to pull 30' ft.
or 40' ft. joints, Crown block….. 6 trip line sheaves, 6 kelly line sheaves & single
sand line sheaf.

Draw works: Drum barrel dia. & length (Trip drum 10” x 13”) (Kelly drum 8” x 17”) maximum single
line pull first wrap (Trip drum 16,600 lbs. w/6 line block) (Kelly drum 16,600 lbs. 3/4” x 525’)
Line dia. & capacity (Trip drum 3/4” x 525’ ft) (Kelly drum 16,600 lbs. 3/4” x 525’ ft) Brakes,
mechanical lugh-leverage type, double self-energized & equalized (Trip drum 27” x 7”)
(Kelly drum 24” x 7”). Auxiliary brake: 15” double rotor parkers none Parkersburg. Catheads, 2,
mounted each end of Kelly drum shaft. One special air actuated for spinning or breakout, mounted
on driller”s side. One foster automatic cathead mounted on opposite side.
 

Rotary Table: Fully enclosed, oil bath type. Spiral bevel gears, ground & lapped in matched sets.
Opening 18” through table for setting casing. Hinges up to allow setting casing up to 34” O.D.
Rotary table, drum & sand reel, 5 forward & 1 reverse.
Air Compressors: for control air….1 or 2 Wabco model 2 AVC mounted on compound case.
For developing wells, ect….model 253-S2 or 50 SDS or equivalent may be installed
on the gooseneck.
 

Engines: 2, each providing 100 continuous BHP, through 17-1/2" fluid couplings,
GM diesel 4031-C is standard; other makes with suitable specs. may be installed.
Compound Case: Engines may be compounded or used singly. Oil spray bath, three shaft, w/jaw clutch.

Transmission: 5 speeds forward….7.20:1, 3.90: 1:2, 12:1:1, 18:1:1, 00:1. 1 speed reverse….7.09:1.
Clutches: Hoisting drum….2 Fawick 18CB500 air clutches; 18”. Kelly drum…. 2 Fawick 21.5E475 air
clutches. 21-1/2”. Rotary table….twin disc CL-211 air actuated clutch. Master clutch….lipe-roll
way 14”; 2 plate. Engines: twin disc 11”; 2 plate. Air Compressor….twin disc 11”; 3-plate.
Controls: Located on side at left of drawworks. Air valve control panel; remote transmission
shifter; throttle; trip & Kelly brakes; hydraulic control & pressure gauge; instrument
panel for engines; weight indicator & driller’s platform.
 

Other Units Cost Extra or Included as a Rig Package:
- Main Generator-60KW, 54KW prime, 2002 Caterpillar model XQ60P2
- Blowout prevention & well control equipment - 8” 3M Regan “Torus” angular preventer 2”
5M Demco valve on side outlet spool, 2” 5M manifold w/adjustable chokes.
- Doghouse/Toolhouse-8” x 36” trailer mounted.
- Substructure-4” w/pony sub.
- Back-up Mud Pump-Ideco 6” x 12” with 325 HP diesel engine.
- (135) Drill Pipe = 4,500’ ft (4-1/2").
- Drill Collars-150’ ft x 6”.
- Survey Machine-Mathey Wireline unit 12,000’ ft with .092 line.
 

Located : Africa

Worldrigs ID: WR768
Model : D120 Drill Rig
Manufacturer : Diedrich
Year : 1991
Condition : Used

Description :

1991 Dierich D120 Drill Rig
John Deere inline 6 diesel Serial #: T06059D43379
990.3 Hours
Moyno 3L8 Pump
500 gallon water tank, Cathead, Fluted kelly, (2) auger racks
Tool boxes, (4) outriggers, 3k, 7k, 10k Winches
Mounted on a 2001 Sterling AT9513 Truck
10 Speed Transmission
Odometer 578,364 miles

Location : USA

Worldrigs ID: WR669
Model : SR50 Drill Rig
Manufacturer : Soilmec
Year : 2006
Condition : Used

Description :

2006 Soilmec SR50 Drill Rig
Hours: 10,935 h
CAT C7 Diesel Engine

Location : Europe

Worldrigs ID: WR846
Description :

2013 Schramm TXD Drill Rig
API Certified Rig
23,635 Hours
Mounted on a Trailer

Items Available for Additional Cost:
Loadsafe System and Pad
Drill Pipe
Collars
Handeling Tools
Doghouse
Air Compressors
Mud Pumps
Pits
Shakers

Location : USA

Worldrigs ID: WR597
Model : T-650 Blast Hole Drill Rig
Manufacturer : Reichdrill
Year : 1989
Condition : Used

Description :

1989 Reichdrill T-650 Blast Hole Drill Rig
1100 CFM / 350 PSI Air Compressor
Rebuilt Cummins KT Diesel Engine
Mounted on an International truck
Rebuilt - Cummins L10 Diesel Engine
DTH Hammer included

Location : USA