Worldrigs ID: WR848
Description :

1997 IMT AF18 Crawler Drill Rig
12,000 hours (+/-) on the rig
Cummins QSL9 Diesel Engine (Tier III & recently installed - only 4,500 hours+/-)

Location : USA

Worldrigs ID: WR870
Description :

Failing Holemaster 1000 Drill Rig
Mounted on a 1974 Mack truck
V8 Mack engine
new 2" Little Giant swivel
23ft kelly
5-1/4" rotary table
256 LeRoi air compressor
Gardner Denver 5x6 piston pump
2 hydraulic leveling jacks

Location : USA

Worldrigs ID: WR832
Description :

2016 Gefco 30K Drill Rig
5,100+ Hours
Mounted on a Peterbuilt 367 6x4 Truck
Cummins rated 550 HP ISX diesel engine (Tier IV)
Sullair 1000 cfm / 350 psi air compressor
Enclosed steel gear box PTO
4 hydraulic leveling jacks
Rotary tophead
6 rod carosel (removed but included in the sale)
15 rod pipe rack
18 gpm Bean water pump
Power sliding holding wrench and table
60” breakout wrench
Pipe spinner
DTH lubricator
Remote controlled jib boom
Moyno 3L8 pump mounted on deck

Location : USA

Worldrigs ID: WR800
Model : 1500 Drill Rig
Manufacturer : Midway
Condition : Used

Description :

Midway 1500 Drill Rig
10" table retracts but needs cylinder
5-1/2 x 8 GD Pump
New transfer case
4 jacks
Long Derrick
Long Kelly
500 of 2-7/8" drill pipe
Auto car
Caterpillar 3406 Diesel Engine
Bill of sale only

Location : USA

Worldrigs ID: WR202

Model : CTM 10,000 Drill Rig
Manufacturer : DeepRock
Year : 1986
Condition : Used

Description :

Deep Rock CTM 10,000 Drill Rig Package

Package Includes:

Deep Rock CTM 10,000 Commercial Water Well Drilling Rig (Trailer Mounted with Single Axle)
Honda 23 HP engine
Hydraulic Driven
Mission 2 x 1-1/2 Mud Pump
Hydraulic Breakout Wrench
Electric Jib Wrench
Mud Pit
Trailer Mounted

Accessories Include:
2-3/8 x 2-3/8 FMxFM subs
2-3/8 x 3-1/2 FMxFM subs
Drag Bits, 3-1/2 to 6 inch
Tri-Cone Bits, 3-1/2 to 6-1/8 inch
4 inch DTH hammer with 4-1/4 inch Bit
4 inch Shock Absorber sub for D.T.H.
Approximately 200 ft. Drill Rod
Good for drilling shallow Screen Wells & DTH Rock drilling to 150 - 200' ft deep

Included as a Package:

Ingersoll-Rand Gyro-Flo Air Compressor
600 CFM / 100 PSI
Powered by Detroit 671 Diesel Engine
Mounted on a 1974 GMC 6500 Truck
366 Gas Engine (rebuilt with less than 10,000 miles)
Allison 4 speed Transmission
Air Brakes
 
Location : USA

Worldrigs ID: WR782
Manufacturer : Speedstar
Condition : As-Is

Description :

Speedstar Quick Drill Rig
Note: only good for Parts
Condition: As-Is
Mounted on Ford Truck

Location : USA

Worldrigs ID: WR464

Model : 1500 Drill Rig
Manufacturer : Howard Turner
Condition : As-Is

Description :

Howard Turner 1500 Drill Rig
Mounted on a Truck
Diesel Engine
HT rotary table drive
Note: Selling the drill rig "as is" to a collector

Location : USA

Worldrigs ID: WR766
Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used

Description :

Simco 2800 Auger / Rotary Drill Rig
Combo auger/rotary
Mounted on 2000 Chevy W4500
Duetz diesel deck engine
25 HP kohler mud pump engine
Mud pump is a 2X3 centrifugal
170 feet of drill rod with 2 roller cone bits
Drill rod is 2-7/8 OD
10 ft extension to the derrick that allows you to work with 20 ft
lengths of pipe
Break out wrench and air compressor on the truck
Truck is a 5 speed cab over
Truck has 135239k and is 2 wheel drive 4 cyl Isuzu diesel
IMT HYD 25CFM @100PSI Air Compressor (?)
Simco thread and set up to run 10 foot lengths

Location : USA

Worldrigs ID: WR689
Model : TH60 Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1979
Condition : Used

Description :

1979 Ingersoll-Rand TH60 Drill Rig
IR 750 cfm / 250 psi Air Compressor - 2 Stage Screw type
Gardner Denver 5X6 Mud Pump (hydraulic driven)
Mounted on a newer 1995 Kenworth T800 Truck
Cummins N14 Diesel Engine - rated 425 HP
4-Motor Tophead with 2-7/8" Threads
200 ft of 20ft x 4.5" x 2-7/8" Drill Pipe
20K Front End
40,000 lbs of Pullback
Rod Box
7-Rod Carousel
Bean Water Injection
Sand Line
Auxiliary PTO for Lift Pump
Two Brand New Batteries
Note: Capable of Handling a Casing Hammer (not included)
2,080 Total Hours (600 hours on it since rebuild in Feb. 2015)
Meter Reads 9,734
The truck is all original
Note: Can be Sold with a service truck and water truck at an extra cost

Location : USA

Worldrigs ID: WR540

Model : T64HB Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T64HB Drill Rig
425 cfm / 250 psi Air Compressor
Detroit 8V71N Diesel Deck Engine
Pipe Rack
3 hydraulic leveling jacks
Mounted on Ford Truck

Location : USA

Worldrigs ID: WR758
Model : T130 Drill Rig - Range III Telescoping Mast
Manufacturer : Schramm
Year : 2004
Condition : Used

Description :

2004 Schramm T130 drill rig - Range III Telescoping Mast - S/N: J130-0110
Substtructure, Rig Floor, Hand Rails, Center Cat Walk
MTU V12-2000TA DDEC Diesel Deck Engine - rated @ 760 HP
Hammer Oilier
130,000 lbs. (59,090 kg) of Pullback
28" inch (711 mm) table opening
50 feet (15.25 m) of clear head travel
3-in ID spindle with optional 5.25-in spindle
Mounted on a CCC (Crane Carrier Company) Truck
VIN# 1CYDGD5874T046284
CAT C12 Diesel Engine - Rated @ 410 HP
Note: New Complete Paint Job finished in May 2013 by EWD with many wells
drilled since
Also available at an extra cost: Dog House, 6000 ft of 4-1/2" IR style drill
pipe, and 1 pipe trailers. (Cost Extra)

Location : USA

Worldrigs ID: WR801
Description :

Mayhew 500 Drill Rig
Gardner Denver FXG172 5x6 Mud pump
7-1/2” rotary table (non-retractable)
18 ft Kelly
4 Jack
2 piston Bean water injection
18 Pipe of 15 ftX 31/4" x 2-3/8" MR Mathew reg drill pipe 270 ft total
Mounted on a Ford F700 Truck
Ford Diesel engine
10 speed transmission
449,042 Miles

Location : USA

Worldrigs ID: WR857
Description :

1973 Gardner Denver 14W Drill Rig
Mounted on a CCC (Crane Carrier Company) Truck
390 ft of Drill Pipe included
Mud Pit & Tee
1000 cfm / 250 psi Air Compressor  
Gardner Denver 5x6 Mud Pump
Bean Water Injection Pump
Cummins 350 Diesel Engine
Foller 13 Speed Transmission
Hour meter reads 1978 Hours
Mileage reads 18,687 Miles
Newer Front tires

Location : USA

Worldrigs ID: WR734
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1981
Condition : Used

Description :

1981 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine
IR 900 CFM / 300 Air Compressor (Inline screw type)
Water Injection Pump
Oil Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Pull Down & 50,000 lbs of Pull Back
18” Table Opening
Hydraulic Cooler
4 & 7 Rod Carousels
4-1/2” x 25ft Used Drill Pipe
3 Outriggers
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine
Complete Part & Service / Repair Manual

Location : USA

Worldrigs ID: WR684
Model : B61 HDX Drill Rig
Manufacturer : Mobile
Year : 1990
Condition : Used

Description :

1990 Mobile B61 HDX Drill Rig
Moyno water pump
Cummins Diesel deck engine
Detroit 671 T Diesel Engine in truck
140 lb. Safety Hammer
100 ft 6-5/8” augers
rods, bits, etc. included

Location : USA

Worldrigs ID: WR768
Model : D120 Drill Rig
Manufacturer : Diedrich
Year : 1991
Condition : Used

Description :

1991 Dierich D120 Drill Rig
John Deere inline 6 diesel Serial #: T06059D43379
990.3 Hours
Moyno 3L8 Pump
500 gallon water tank, Cathead, Fluted kelly, (2) auger racks
Tool boxes, (4) outriggers, 3k, 7k, 10k Winches
Mounted on a 2001 Sterling AT9513 Truck
10 Speed Transmission
Odometer 578,364 miles

Location : USA

Worldrigs ID: WR837
Description :

Geoprobe 8150LS Crawler Drill Rig
Geoprobe 50DT Track Base Platform
Geoprobe GV5 Sonic Head Long Stroke
Geoprobe Designed Rod Handling
System Head Feed Stroke: 157"
50K Dynamic Force
Remote Diagnostics
Adjustable Swing-arm Control Panel
Automatic Drop Hammer 140 lb
Winch Kit: 2,500 lb

Safety Cage
Triplex High Pressure Water Pump
Air Compressor Kit, C6.6 with BA-922
Drop Rack System with Rod Rack
Drill Mast Side-Shift
Head Centerline Side-Shift
Fits in 40 ft Shipping Container for Exporting
10-ft Tooling Compatible
Rock Coring Compatible
14" in Double Wrench Breakout

Dual Winch System
Front and Rear Outriggers (Four Point Stabilization)
Sonic tooling inventory with rig: (extra cost or included as a package)
Two tooling indexing racks with rollers
230 ft of 4 tooling
230 ft of 6” tooling
100 ft of 8” tooling
One Actuator core for rod handler
One SDT-60 Weighted Wire Line Core Barrel
Several bits and adapters
(Cost Extra or included as a package for all listed together)
2010 Freightliner model Cascadia Truck with Diesel Engine (492,560 miles)
Trailer for the hauling the drill, pipe, and tooling (as is in the pictures)
1210 Hours on Engine, 210 Hours on Sonic Head at time of listing.

Location : USA

Worldrigs ID: WR873
Description :

2009 Simco 2800 Drill Rig
Note: this is set up as a water well / geothermal drill & If you prefer a 2800 HSHT
set up for geotechnical drilling with auto hammer that is possible,
Rod 3" PDQ style 10 foot length
Ingersoll-Rand 375 CFM / 170 PSI Air Compressor
Centerline Monoplex Mud Pump
Rod box
FMC I0413C Water injection pump
Deutz Diesel Deck Engine (rated 70 HP)
2 Winches
Mounted on a 1994 Chevrolet Kodiak 4x4 truck
Caterpillar 3116 Diesel Engine

Location : USA

Worldrigs ID: WR410

Description:

Engine: originally GMC Detroit Diesel, now has a Cummings 6BTA 5.9, Manufacture date of 10/26/1989

Worldrigs ID: WR773
Model : T64HB Drill Rig - Retrofitted
Manufacturer : Schramm
Year : 1978
Condition : Used

Description :

1978 Schramm T64HB Drill Rig - Retrofitted in year 2000
Detroit 8V92 diesel deck engine
T660 Derrick replaced the T64HB Derrick
Sullair 900 cfm / 350 psi Air Compressor
Carousel
Pipe Rack
Hydraulic Leveling Jacks
Mounted on a 1986 Ford L8000 Truck
CAT 3208 diesel engine
13 speed Eaton fuller transmission

Location : USA

Worldrigs ID: WR492
Speedstar S S61A Cable Tool Rig Details:

Worldrigs ID: WR670
Model : SR30 Drill Rig
Manufacturer : Soilmec
Year : 2017
Condition : Used

Description :

2017 Soilmec SR30 Drill Rig
Hours: 1000 (as of Oct 2018)
Cummins QSB6.7-T4F Diesel Engine

Location : Europe

Worldrigs ID: WR494

Model : 650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic 650 Drill Rig
CP 450 CFM / 250 PSI Piston Compressor with 750/350(?)
Booster (air clutch needs newdiapragm)
Tiger Tierra Casing Driver
Carousel

Package Includes:
300’ ft of used drill pipe (some need new pins and boxes)
6” and 9” DTH Hammers
6” Tricone button bit

Spare Parts included; main pumps, top head motors, inner cooler, valves for
the compressor, new drive chain for the transfer case

Rig in working order, some oil leaks (packings need replaced).
Mounted on a 1973 International Paystar truck

Location : USA

Worldrigs ID: WR331

Description :
 

The RB 15 enables the user to drill with the following methods, with borehole
diameters 4” (108 mm) to 24” (609 mm):
 

Rotary-drilling with direct circulation
Rotary-drilling with reverse circulation Auger-drilling
 

Percussion core drilling (ram coring)
Wire-line core drilling 
Down-The-Hole hammer drilling (direct / reverse)
Free-fall drilling
Geothermal Drilling with DoubleRotation-Head
Inclined Drilling max.45 degrees
 

Additional rig components
Addit. to specifications overleaf
Foam pumpe
Line oiler (for DTH)
Free-fall winch
Hose winch
Percussion drilling device
Hydraulically driven Gen-set
Hydraulically driven welding-set
Rod handling arm
Rod box
 

Base carrier : Crawler base
 

Crawler width / Track shoe width : 2.450 / 500 mm
Transport dimensions L / W / H Diesel Engine (water-cooled) : 10.000 / 2.540 / 3.200 mm
Exhaust Emission Standard : EPA / Carb Tier 3, EU Stufe 3A
Rated output : 205 kW @ 2.200 U/min (rpm)
Diesel tank capacity : 280 l
Feed device (hydr. cylinder)
Push-down / Pull-back force : 70 / 140 kN
Feed speed : 0 - 0,8 m/s
 

Power swivel : L130
Gear select, 3 speeds
Torque at 0 - 34   rpm : 11.750 Nm
Torque at 0 - 100 rpm : 4.150 Nm
Torque at 0 - 320 rpm : 1.200 Nm
 

Chuck & break device : HSB 178.300
Clamping diameter max. / min. : 170 / 51 mm
Max. breaking torque : 41.000 Nm
 

Outrigger cylinder
Max. stroke : 600 mm
 

Mast head with hydr. swing-out device
Swing-out displacement : 700 mm
Swing-out force : 8 kN
 

Clamping device
Max. clearance diameter : 400 mm
Max. casing nominal diameter : DN 255
Max. clamping force : 300 kN

Winches
Main winch
Line pull 1st layer : 95 kN
Wire rope diameter / rope length : 20 / 130 m
Coring winch
Line pull 1st layer : 20 kN
Wire rope diameter / rope length : 8 / 300 m
Auxiliary / percussion winch
Line pull 1st layer : 26 kN
Wire rope diameter / rope length : 10 / 49 m

Pumps
Triplex piston pump
Discharge / Operating pressure : 270 l/min / 40 bar
Duplex piston pump
Discharge / Operating pressure : 450 l/min / 20 bar
Eccentric screw pump
Discharge / Operating pressure : 350 l/min / 24 bar
Centrifugal pump
Discharge capacity / Op.pressure : 1.500 l/min / 8 bar
Suction pump
Discharge capacity / Suction height : 5.300 l/min

Screw type compressor Compressor
Discharge / Operating pressure : 7 m³/min / 15 bar
Rotating casing table : VDT 324  VDT 419

Torque : 13 / 20 kNm  30 / 45 kNm

Worldrigs ID: WR846
Description :

2013 Schramm TXD Drill Rig
API Certified Rig
23,635 Hours
Mounted on a Trailer

Items Available for Additional Cost:
Loadsafe System and Pad
Drill Pipe
Collars
Handeling Tools
Doghouse
Air Compressors
Mud Pumps
Pits
Shakers

Location : USA

Worldrigs ID: WR883
Description :

1981 Chicago Pneumatic T-700WH Deep Hole Drill Rig & Package
900/350 on-board air,
mounted on a tandem axle steer Kenworth carrier -75,000# pull-back,
4-rod carousel,
CAT 3406B deck engine recently replaced (less than 500 hours ago),
rebuilt dual top-head motors and planetaries,
rebuilt rotational pump and fan motor/pump,
new Nylotron head guides,
new winch line

Additional equipment included :
3,200ft 4 1/2"  x 30ft drill pipe with tandem axle drill pipe trailer
mounted IR tugger winch,
skid mounted Sullair 900/350 air compressor,
skid mounted 2000 gallon fuel tank,
skid mounted 300 bbl water tank,
skid mounted doghouse,
spare CAT 3406B engine (needs rebuilt),
6" hammer, 12" hammer/stabilizer combo,
12" tri-cone stabilizer,
casing lifters for both threaded and plain-end,
casing slips, break out wrench, J-wrench.

Location : USA

Worldrigs ID: WR766
Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used

Description :

Simco 2800 Auger / Rotary Drill Rig
Combo auger/rotary
Mounted on 2000 Chevy W4500
Duetz diesel deck engine
25 HP kohler mud pump engine
Mud pump is a 2X3 centrifugal
170 feet of drill rod with 2 roller cone bits
Drill rod is 2-7/8 OD
10 ft extension to the derrick that allows you to work with 20 ft
lengths of pipe
Break out wrench and air compressor on the truck
Truck is a 5 speed cab over
Truck has 135239k and is 2 wheel drive 4 cyl Isuzu diesel
IMT HYD 25CFM @100PSI Air Compressor (?)
Simco thread and set up to run 10 foot lengths

Location : USA

Worldrigs ID: WR862
Description :

2011 Schramm RC685 Exploration Drill Rig
MTU V2000 Diesel Deck Engine
Sullair 1350 cfm / 500 psi Air Compressor
Hours : 12,317
Miles : 7,129
Boart Longyear Rod Handler
Hydraulic Pumps
Collector Box & Cyclone
Drill Table Opening : 22 inch
Rod Spinner & hydraulic breakout wrenches
Rated Depth Capacity : 5-1/2" diameter hole to 2,300 feet deep
Rated Pullback : 94,000 lbs
CAT Walk
Hydraulic Leveling Jacks
Mounted on a 2012 International Truck
MaxxForce Diesel Engine
Misc Drill Tooling for an extra cost (in pictures) Stablizer,
Hole Opener, Collar, Land Plates

Note: Set up for RC (Reverse Circulation) minerial exploration & mining.
This is not a T685 model for water wells

Location : USA

Worldrigs ID: WR879
Description :

1979 Chicago Pneumatic 600 Drill Rig
Detroit 6V93 Diesel Deck Engine
GHH 600 CFM / 300 PSI Air Compressor
320 ft of 4-1/2" x 20 ft Drill Pipe included
Recent Cooler and Drill Head Rebuilt
Mounted on a 1990 Mack Truck
300 HP Diesel Engine

Location : USA

Worldrigs ID: WR214

Model: 650 Drill Rig
Manufacturer: Chicago Pneumatic
Year: 1986
Condition: Used

Description :

1986 Chicago-Pneumatic 650 Drill Rig
GHH 825 cfm / 350 psi Air Compressor
CAT 3406 diesel deck engine
Mounted on Ford truck
diesel engine
Around 1,000 ft of near new drill pipe at extra cost

Location : USA

Worldrigs ID: WR153

Model : 3000-CF Drill Rig
Manufacturer : Failing
Condition : Used

Description :

Failing / Gefco Holemaster 3000-CF Drill Rig
Factory Rated Capacity: 3,700 ft. depth using 3-1/2” drill pipe.
Mast: Cold drawn street tubing, elec. Welded, 3-sect. with 3-way taper on top sect.
Hydraulically raised & lowered. Wired for elec. Lights. Equipped w/retracting
channel swivel guides for reverse circulation swivel. Equipped with ladder,
climber’s safety device.
 

Hgt. 72” Telescoping, Width 86” center to center of mast legs, Depth 48” center
to center of mast legs, Capacity total gross 133,000 lbs. hook load 100,000 lbs.
Racking board capacity 3,000 ft. of 3-1/2” drill pipe, may be mounted to pull 30' ft.
or 40' ft. joints, Crown block….. 6 trip line sheaves, 6 kelly line sheaves & single
sand line sheaf.

Draw works: Drum barrel dia. & length (Trip drum 10” x 13”) (Kelly drum 8” x 17”) maximum single
line pull first wrap (Trip drum 16,600 lbs. w/6 line block) (Kelly drum 16,600 lbs. 3/4” x 525’)
Line dia. & capacity (Trip drum 3/4” x 525’ ft) (Kelly drum 16,600 lbs. 3/4” x 525’ ft) Brakes,
mechanical lugh-leverage type, double self-energized & equalized (Trip drum 27” x 7”)
(Kelly drum 24” x 7”). Auxiliary brake: 15” double rotor parkers none Parkersburg. Catheads, 2,
mounted each end of Kelly drum shaft. One special air actuated for spinning or breakout, mounted
on driller”s side. One foster automatic cathead mounted on opposite side.
 

Rotary Table: Fully enclosed, oil bath type. Spiral bevel gears, ground & lapped in matched sets.
Opening 18” through table for setting casing. Hinges up to allow setting casing up to 34” O.D.
Rotary table, drum & sand reel, 5 forward & 1 reverse.
Air Compressors: for control air….1 or 2 Wabco model 2 AVC mounted on compound case.
For developing wells, ect….model 253-S2 or 50 SDS or equivalent may be installed
on the gooseneck.
 

Engines: 2, each providing 100 continuous BHP, through 17-1/2" fluid couplings,
GM diesel 4031-C is standard; other makes with suitable specs. may be installed.
Compound Case: Engines may be compounded or used singly. Oil spray bath, three shaft, w/jaw clutch.

Transmission: 5 speeds forward….7.20:1, 3.90: 1:2, 12:1:1, 18:1:1, 00:1. 1 speed reverse….7.09:1.
Clutches: Hoisting drum….2 Fawick 18CB500 air clutches; 18”. Kelly drum…. 2 Fawick 21.5E475 air
clutches. 21-1/2”. Rotary table….twin disc CL-211 air actuated clutch. Master clutch….lipe-roll
way 14”; 2 plate. Engines: twin disc 11”; 2 plate. Air Compressor….twin disc 11”; 3-plate.
Controls: Located on side at left of drawworks. Air valve control panel; remote transmission
shifter; throttle; trip & Kelly brakes; hydraulic control & pressure gauge; instrument
panel for engines; weight indicator & driller’s platform.
 

Other Units Cost Extra or Included as a Rig Package:
- Main Generator-60KW, 54KW prime, 2002 Caterpillar model XQ60P2
- Blowout prevention & well control equipment - 8” 3M Regan “Torus” angular preventer 2”
5M Demco valve on side outlet spool, 2” 5M manifold w/adjustable chokes.
- Doghouse/Toolhouse-8” x 36” trailer mounted.
- Substructure-4” w/pony sub.
- Back-up Mud Pump-Ideco 6” x 12” with 325 HP diesel engine.
- (135) Drill Pipe = 4,500’ ft (4-1/2").
- Drill Collars-150’ ft x 6”.
- Survey Machine-Mathey Wireline unit 12,000’ ft with .092 line.
 

Located : Africa

Worldrigs ID: WR667
Model : Drill Rig
Manufacturer : Gus Pech
Condition : Rebuilt
Quantity : 3

Description :

Gus Perch Drill Rig
Rig #1 - 2006 Gus Pech - 11,600 Hours
Rig #2 - 2007 Gus Pech - 10,000 Hours
Rig #3 - 2008 Gus Pech - 5,000 Hours
Rigs were overhauled at Gus Pech Factory in 2017.
All rigs have 700/200 Sulliar Compressors
All rigs have 7X10 Centreline Mud Pumps
All Rigs 450hp Mercedes Engines

Location : North America

Worldrigs ID: WR878
Description :

Davey Rouselle M8A Drill Rig
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Within the last 2 years the drill has had the air compressor "gone through"
Has had the table replaced
Ramsey pulldown winch replaced
Chain cases replaced
Table transmission rebuilt
New radiator for deck engine
Various other small repairs done
Deck engine needs repaired or replaced
Comes with 100ft of 4.5”x 30ft Kelly and 4” Davey rods
Davey Changeover sub to 3.5 API threads for bit - with wrenchs and slips
Mounted on 1991 Sterling truck
Truck Runs fine but 4th gear does jump out
Truck has a 3306 cat motor in it and an 8 speed transmission
Tires are in good shape.
Drill motor is getting weak and will need rebuilt - Can be replaced for an extra cost
Lots of repairs and rebuilds in the last 2 years.

Location : USA

Worldrigs ID: WR798
Model : CM-780D Blasthole
Manufacturer : Ingersoll-Rand
Year : 2003
Condition : Used

Description :

2003 Ingersoll-Rand CM-780D Blasthole Drill Rig
Crawler Mounted
Caterpillar Diesel Engine
S/N: G78255EL
IR HR2 865 CFM / 350 PSI Air Compressor
Water injection
Hammer Lubricator
Thread Greaser
Enclosed Cab
A/C & Heater
Rod Changer
13-1/2" Track Shoes
Set up for (3-1/2”O.D. x 13.1ft) Drill Pipe 21/2Z thread
Meter Reads 15,940 Hours

Location : USA

Worldrigs ID: WR831
Description :

1996 Speedstar SD300 Drill Rig
Mounted on an 1995 International Truck
Cummins N14 Diesel Engine
10 Speed transmission
Sullair 750 cfm / 350 psi air compressor with clutch
Gardner Denver 5x6 Duplex Mud Pump (hydraulic driven)
Pipe rack
Hydraulic Leveling Jacks

Location : USA

Worldrigs ID: WR864
Description :

2017 Mobile B37X Crawler Drill Rig
600 Hours
8,000 ft/lb
1050 RPM
13 ft stroke
Auto hammer
308 Undercarriage
20,000 lb main winch
Bean 1122 pump
1,000 psi piping
Wireless
John Deere 140HP- tier 3
Angle Drill

Selling Fully Tooled:
44 lightly used 4 1/4 HS augers
820 ft NQ rods
20 ft Longyear barrel
10 ft HQ barrel
190 ft of AWJ rods

Location : USA

Worldrigs ID: WR178

Model : 1250 Drill Rig
Manufacturer : Failing
Condition : As-Is

Description :

(1) Failing 1250 Drill Rig (being sold for parts)
No Rotary Table
No Mud Pump
No Transfer Case
No Kelly
No Chains
(Basically If You Need A Tower Or Something)
Mounted on a International Truck
Diesel Engine
(1) International 1500 Galloon Water Truck
10 Wheel
Water tank built to bed -O- to haul from pipe beside tank

Location : USA

Worldrigs ID: WR691
Model : 1500 drill rig
Manufacturer : Gardner Denver
Condition : Used

Description :

Gardner Denver 1500 drill rig
5x6 mud pump
kelly drive recentlly rebuilt
Mounted on a twin axle carrier
Diesel engine
Note: no air compressor on board

Location : USA

Worldrigs ID: WR662
Model : T25K3W Drill Rig
Manufacturer : Driltech
Year : 1994
Condition : Used

Description :

1994 Driltech T25K3W Drill Rig- S/N: 731889
Sullair 840 cfm / 350 psi Air Compressor
CAT 3406 DITA Diesel Deck Engine - rated 430 HP @ 1,800 RPM
30,000 LBS of Pullback
28 ft Head Travel
Pipe Rack Holds For 15 Pipe
(6) Rod Carousel
Rotary Head - rated 89 RPM & 62,600 in LBS. Torque
Jib Boom, Hydraulic Extend With 172 Degree Hydraulic Swing
Hydraulic Winch 7,500 LBS. Capacity
20" Openiing in Table With Hydraulic Adjustment
48" Jaw Type Breakout Wrench
Water Injection Pump is 20 GPM With Foam Pump
DTH Lubricator With 10 Gallon Tank
Fine Feed  & Torque Controls
420 ft. of Used Drill Pipe (4-1/2" O.D. X 20ft) & Basic Tooling Included
Gardner Denver 5 X 6 Air Drive Mud Pump on Board
Hydraulic Leveling Jacks
Mounted on a 1993 Ford LNT8000 - VIN #1FDZW82E0PVA18231
Cummins 8.3l 275 Hp Diesel Engine
10 Speed Transmission
18,000 Front Axle
46,000 Rear Axle

Location : USA

Worldrigs ID: WR859
Description :

1978 Portadrill 524-3A Drill Rig
Gardner-Denver 5-1/2" Mud Pump
Leroi 256 S-2 250 PSI Air Compressor
Hydrostatic drawworks and rotary table
Pipe Slide
Injection pump
Hydraulic leveling jacks
Mounted on a 1999 Ford Louisville truck
Powered by Cummins Red Top N14 Diesel Engine - rated 500 HP
Tag axle

Location : USA

Worldrigs ID: WR671
Model : C-700 Drill Rig
Manufacturer : Reichdrill
Condition : Used

Description :

Reichdrill C-700 Crawler Drill Rig
Sullair 900 CFM / 375 PSI Air Compressor
Caterpillar 3406 T Diesel Deck Engine
Water Injection Pump
Hammer Lubricator
Drillers Cab
Caterpillar Undercarriage
Metal Tracks

Location : USA

Worldrigs ID: WR841
Description :

2003 Scrammm T660 Drill Rig Package
Mounted on 2003 Freightliner
10054 hours.
GHH compressor, 1000 CFM @ 350 PSI.
Rig has 685 top head drive gearbox and shocksub.

Compressor #1:
Sullair model 1150XHDTO
1150 CFM @ 350 PSI
Compressor had engine and compressor replaced in 2011, has about
2000 hours now mounted on 39ft tandem axle float with catwalks
and stair (with 2 compressors on it).

Compressor #2:
Sullair 1150XHDT
1150 CFM @ 350 PSI
10085 hours
Mounted on 39ft tandem axle float with catwalks and stair
(with 2 compressors on it)
Hurricane Booster
6T 276-41B 1000
Meter shows 352 hours
skid mounted
1800ft 4 1/2 x 25ft drill pipe, 2 7/8 IF
on 50ton triple axle trailer.
Hydraulic winch on trailer plugs into rig hydraulics
2 drill collars
15" stabilizer
8" and 12" Hammer

Location : USA

Worldrigs ID: WR801
Description :

Mayhew 500 Drill Rig
Gardner Denver FXG172 5x6 Mud pump
7-1/2” rotary table (non-retractable)
18 ft Kelly
4 Jack
2 piston Bean water injection
18 Pipe of 15 ftX 31/4" x 2-3/8" MR Mathew reg drill pipe 270 ft total
Mounted on a Ford F700 Truck
Ford Diesel engine
10 speed transmission
449,042 Miles

Location : USA

Worldrigs ID: WR197

Model : Heli-Rig 700 HP Package
Manufacturer : Generic
Condition : Used

Description :

Mid-Continent U-36 Ae Diesel Electric @ 700 HP, S/D Drawworks,
Lebus Grooved F/1-1/8" Line, Air Drillers Console, 22" Hydromatic Brake,
Hydraulic Tank Pump P/B @ 2 HP Electric Motor, P/B Ge 752 Traction Motor,
with Blower, @ 1000 HP,All Mounted Covered Skid with Fluorescent Lights,
Ruffneck Heater, Master Skidded

Mast :
Parco 131' H x 17'8" W Cantilever Mast, 360,000 lbs Sheaves, Pin-Type, Crown Block,
(5) 36" Sheaves, 46" Fastline Sheave, 1-1/8" Line, 4" Standpipe, Crown Safety Platform
Racking Board, Tong Counterweights, Ladder, Derrick, Climber, Mast Stand,
Fluorescent Lights.

Sub :
Parco 22' H x 25' W X 35' L Self-Elevating Substructure, Self-Skidded, Rotary Beams,
Stairs, Safety Rails, Deadline Anchor, Skidded with V-Door, 42" H x 5' W x 32' L,
2- Section Catwalk with Steel Deck

Top Drillers House :
10' H x 8' W x 20' L Rd Top Doghouse with 3' l Porch, Knowledge Box, Lockers,
Lights, Bench & Cabinet Storage, Remote Closing Unit, Skidded

Scr House:
Baylor Model Se-33-Ba-301, 3-Bay Scr Drive System, S/N: 1001-61054, 600 Vac,
60hz Input, Multiple Controlled Dc Outputs At 0-750 Vdc, Allen Bradley
Switch Gear & Baylor Instrumentation, (2) Marcus Transformers, (1) 600-400 Volts
(1) 460-208 Volts, Mtd In 10' H x 10'6" W x 20'l House, Lennox T-Class Heat/Air Unit,
Emergency Lights, Skidded.

Generators :
(1) Caterpillar 600kw Generator, P/B CAT 3412 Diesel Engine (S/N 81z0127),
Electric Start, Radiator, Gauges,
(1) Bbc 715 700kw Generator Set, P/B Cat 3412 880hp Diesel Engine
S/N 38s2v356, Air Start, Radiator, Gauges,
Both Mounted in a Skidded 10' W x 36' L Generator House, Fluorescent
Lights, Day Tank,

Location : USA

Worldrigs ID: WR774
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1995
Condition : Used

Description :

1995 Ingersoll-Rand T4W Drill Rig
IR 1000 cfm / 350 psi Air Compressor - (14,000 hours)
Cummins QSK Diesel Deck Engine - rated 600 HP & 2100 RPM - (Reman
as of March 2016 with 1,971 hours on meter as of 8-6-2019)
50,000 lbs of pullback
Worm Gear Power Head
Water Injection Pump
Hammer Lubricator
7 & 4 Rod Carousel
Starting Aid Diesel Fired Pre-heater with Ether
Hydraulic Leveling Jacks
Mounted on a CCC (Crane Carrier Company) Truck
Caterpillar 3306 C diesel engine
mileage 75,000

Location : USA

Worldrigs ID: WR331

Description :
 

The RB 15 enables the user to drill with the following methods, with borehole
diameters 4” (108 mm) to 24” (609 mm):
 

Rotary-drilling with direct circulation
Rotary-drilling with reverse circulation Auger-drilling
 

Percussion core drilling (ram coring)
Wire-line core drilling 
Down-The-Hole hammer drilling (direct / reverse)
Free-fall drilling
Geothermal Drilling with DoubleRotation-Head
Inclined Drilling max.45 degrees
 

Additional rig components
Addit. to specifications overleaf
Foam pumpe
Line oiler (for DTH)
Free-fall winch
Hose winch
Percussion drilling device
Hydraulically driven Gen-set
Hydraulically driven welding-set
Rod handling arm
Rod box
 

Base carrier : Crawler base
 

Crawler width / Track shoe width : 2.450 / 500 mm
Transport dimensions L / W / H Diesel Engine (water-cooled) : 10.000 / 2.540 / 3.200 mm
Exhaust Emission Standard : EPA / Carb Tier 3, EU Stufe 3A
Rated output : 205 kW @ 2.200 U/min (rpm)
Diesel tank capacity : 280 l
Feed device (hydr. cylinder)
Push-down / Pull-back force : 70 / 140 kN
Feed speed : 0 - 0,8 m/s
 

Power swivel : L130
Gear select, 3 speeds
Torque at 0 - 34   rpm : 11.750 Nm
Torque at 0 - 100 rpm : 4.150 Nm
Torque at 0 - 320 rpm : 1.200 Nm
 

Chuck & break device : HSB 178.300
Clamping diameter max. / min. : 170 / 51 mm
Max. breaking torque : 41.000 Nm
 

Outrigger cylinder
Max. stroke : 600 mm
 

Mast head with hydr. swing-out device
Swing-out displacement : 700 mm
Swing-out force : 8 kN
 

Clamping device
Max. clearance diameter : 400 mm
Max. casing nominal diameter : DN 255
Max. clamping force : 300 kN

Winches
Main winch
Line pull 1st layer : 95 kN
Wire rope diameter / rope length : 20 / 130 m
Coring winch
Line pull 1st layer : 20 kN
Wire rope diameter / rope length : 8 / 300 m
Auxiliary / percussion winch
Line pull 1st layer : 26 kN
Wire rope diameter / rope length : 10 / 49 m

Pumps
Triplex piston pump
Discharge / Operating pressure : 270 l/min / 40 bar
Duplex piston pump
Discharge / Operating pressure : 450 l/min / 20 bar
Eccentric screw pump
Discharge / Operating pressure : 350 l/min / 24 bar
Centrifugal pump
Discharge capacity / Op.pressure : 1.500 l/min / 8 bar
Suction pump
Discharge capacity / Suction height : 5.300 l/min

Screw type compressor Compressor
Discharge / Operating pressure : 7 m³/min / 15 bar
Rotating casing table : VDT 324  VDT 419

Torque : 13 / 20 kNm  30 / 45 kNm

Worldrigs ID: WR660
Model : T4BH (Blast Hole) Drill Rig
Manufacturer : Atlas Copco
Year : 2006
Condition : Used

Description :

2006 Atlas Copco T4BH (Blast Hole) Drill Rig
Serial Number: 8294
Cummins QSK19 Diesel Deck Engine
IR HR2.5 1250 CFM / 350 PSI Air Compressor
Dual Motor Spur Gear Power Head
LT Long Tower runs (30ft Drill Pipe)
CCC : Cummins isx 15 , 475hp

Location : Middle East Region

Worldrigs ID: WR469

Model : T450GT Drill Rig
Manufacturer : Schramm
Year : 2008
Condition : Used

Description :

2008 Schramm T450GT Crawler Drill Rig
Caterpillar C-15 diesel engine @ 580 HP - S/N JRE09405
Sullair 1050 cfm / 350 psi air compressor with clutch
Floating sub
15 Rod Carousel - handles 3-1/2" Pipe
500' ft of 3-1/2" x 20' x 2-3/8" IF thread (estimated 50% condition)
Washington diverter
Hydraulic welder
Hammer lubricator
4 piston water injection pump
Rod spinner
2 motor power head
6,440 hours on gauge

Location : USA

Worldrigs ID: WR787
Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used

Description :

Simco 2800 Auger Drill - Unmounted
Year: 1976 / 1977
Dual Motor Hydraulic Top Rotary Power Head (swings away)
11 ft. 6 in. mast (retracted), approximately 18 ft. mast extended
Cathead
Winch
Wisconsin 4 cylindergas motor
In working order
Currently unmounted but comes with trailer it was previously mounted on
included in deal

Location : USA

Worldrigs ID: WR767
Model : M8 Drill Rig
Manufacturer : Davey
Condition : Used

Description :

Davey M8 Table Drive Water Well Drill Rig
500 CFM Air Compressor
In working order
With spare tower & parts

Location : USA

Worldrigs ID: WR492
Speedstar S S61A Cable Tool Rig Details:

Worldrigs ID: WR836
Description :

1977 Ingersoll-Rand TH60 Drill Rig
IR 600 cfm / 250 psi air compressor
Mission style magnum mud pump
Pipe Rack
Mounted on a 1977 International Paystar Truck
Detroit 8V71 Diesel Engine (Rebuilt in 2013-2014)
Hydraulic Leveling Jacks
Drill Pipe is not included (cost extra)

Location : USA

Worldrigs ID: WR781
Model : DSI QuikDrill Rig
Manufacturer : Speedstar
Condition : Used

Description :

Speedstar DSI QuikDrill
Failing FM-3 Mud Pump
Has Air Compressor (Not Working)
Mounted on 2001 International 4900 Truck
Powered by 7.6 L 466 CID L6 International DT466 Diesel Engine

Location : USA

Worldrigs ID: WR861
Description :

Schramm T130 Drill Rig
Diesel Deck Engine
Mounted on a CCC Truck
Diesel Engine

Included as a package:
4-1/2" Bottle Neck X Hole Drill Pipe
6" Collars = 90 ft
All Subs needed to drill
Spare Motor
Spare Parts : Top Drive (Rebuilt no hours), New Spindle,
Bearings for top drive, Chive Crown
Pipe Racks with Catwalk (30 ft L X 5 ft W X 3-1/2 ft T)

Location : USA