Worldrigs ID: WR761
Model : T500XD Drill Rig
Manufacturer : Schramm
Year : 2013
Condition : Used

Description :

2013 Schramm T500XD Drill Rig
1,500 HP Drilling Rig
Fluid Pressure Rating: 7,500 psi

Power Unit :
MTU 12V -2000 engines, 760 bhp (567 kw) @ 1,800 rpm with electric start
Dual core, side by cooling package, 130”F ambient rating
220 gallon diesel fuel tanks
Hydraulic pump systems, with each including (8) piston pump systems
and (1) gear type pump
(1) 1,000 gallon hydraulic tank with (18) twin element hydraulic tank
with (18) twin element hydraulic tank with (18) twin element hydraulic
tank with (18) twin element hydraulic tank with (18) twin element filters

Sub -Base and Walking System :
Floor Height : 22 ft.
Clearance : 19 ft. under table bushing

Telemast System :
Top Head Travel: 56 ft.
Hook Load : 500,000 lbs. actual Hoist
80,000 lbs pulldown capacity

Tilting Top Drive :
Rotation Speed: 0-140 RPM
Rotation Torque: Up to 35,000 ft-lbs

Rig Floor :
37.5 inch false table adapter and a 27.5 inch Master Bushing

Hydraulic Roughneck :
Make/Break Torque: 60,000 ft -lbs @ 3,500 psi
Loadsafe XD Pipe Handling System

Mud Pumps :
(2) Gardner Denver PZ-11HP 1,000 HP / 7,500 PSI

Power :
One, Detroit diesel 16V2000P EPA Tier 1 One

Standard Accessories :
Water injection system, rated 35 gpm @ 1,000 psi
DTH lubricator rated up to 5 gph (19 lph ) @ 1,000 psi ) @ 1,000 psi
Air manifold for air drilling operations
Air/mud fluid lines, 4 inch stand pipe and traveling hose for
7,500 psi operation
Explosion proof 240V lighting for nighttime operation
(customer supplied generators) BOP handling system,
carriage and trolley rated 40,000 lbs.
Support Equipment :
40ft Conex BoX : with spare parts for Rig

Trip Tank :
Fabricated skid mounted tank with (40 bbl. of capacity) 4 x 3 centrifugal pump

Mud Pits :
Two tanks – shaker tank and suction (750 bbls). Shakers – Vortex triple
shakers w/5 agitators.
Mud hopper.Class 1 Div 1 lighting

Location : USA

Worldrigs ID: WR696
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1974
Condition : Used

Description :

1974 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine (inframe rebuilt)
IR HP 750 CFM / 250 Air Compressor
Water Injection Pump
Oil Injection Pump
Two Winch Lines
Carousel
36” Mast (Autofeed)
Pull Down & Pull Back
18” Table Opening
Worm Gear Top Head
Hydraulic Cooler
Rod Changer
Handles 4-½” x 25ft Drill Pipe
3 Outriggers
Complete Part & Service / Repair Manual
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Slow & Fast Rotation
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine

Location : USA

Worldrigs ID: WR859
Description :

1978 Portadrill 524-3A Drill Rig
Gardner-Denver 5-1/2" Mud Pump
Leroi 256 S-2 250 PSI Air Compressor
Hydrostatic drawworks and rotary table
Pipe Slide
Injection pump
Hydraulic leveling jacks
Mounted on a 1999 Ford Louisville truck
Powered by Cummins Red Top N14 Diesel Engine - rated 500 HP
Tag axle

Location : USA

Worldrigs ID: WR145

Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used
Year : 1989

Description :
 
1989 Simco 2800 Drill Rig
Mounted on a 1989 F600 Truck with Diesel Engine
20' stroke in the tower (10000 lbs of thrust & 4000 lbs rotation)
Mission 2x3 mud pump
Sullair compressor
200' ft of simco pdg drill pipe
Mud Pan attached to the truck
 

Location : USA

Worldrigs ID: WR862
Description :

2011 Schramm RC685 Exploration Drill Rig
MTU V2000 Diesel Deck Engine
Sullair 1350 cfm / 500 psi Air Compressor
Hours : 12,317
Miles : 7,129
Boart Longyear Rod Handler
Hydraulic Pumps
Collector Box & Cyclone
Drill Table Opening : 22 inch
Rod Spinner & hydraulic breakout wrenches
Rated Depth Capacity : 5-1/2" diameter hole to 2,300 feet deep
Rated Pullback : 94,000 lbs
CAT Walk
Hydraulic Leveling Jacks
Mounted on a 2012 International Truck
MaxxForce Diesel Engine
Misc Drill Tooling for an extra cost (in pictures) Stablizer,
Hole Opener, Collar, Land Plates

Note: Set up for RC (Reverse Circulation) minerial exploration & mining.
This is not a T685 model for water wells

Location : USA

Worldrigs ID: WR878
Description :

Davey Rouselle M8A Drill Rig
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Within the last 2 years the drill has had the air compressor "gone through"
Has had the table replaced
Ramsey pulldown winch replaced
Chain cases replaced
Table transmission rebuilt
New radiator for deck engine
Various other small repairs done
Deck engine needs repaired or replaced
Comes with 100ft of 4.5”x 30ft Kelly and 4” Davey rods
Davey Changeover sub to 3.5 API threads for bit - with wrenchs and slips
Mounted on 1991 Sterling truck
Truck Runs fine but 4th gear does jump out
Truck has a 3306 cat motor in it and an 8 speed transmission
Tires are in good shape.
Drill motor is getting weak and will need rebuilt - Can be replaced for an extra cost
Lots of repairs and rebuilds in the last 2 years.

Location : USA

Worldrigs ID: WR697
Model : Rotadrill T64HB Drill Rig
Manufacturer : Schramm
Year : 1974
Condition : Used

Description :

Schramm Rotadrill T64HB Drill Rig
Rebuilt - Detroit Diesel Deck Engine
No Air Compressor on deck
Tool Carrying Cabinet
Reinforced Mast
Heavy Winch line
3 Outriggers
Hydraulic Pull down & Pull Back
Multiple speed top head motor
Hydraulic Cooler
Autofeed
Mounted on a 1974 International RO Truck
Newer 6 Cylinder Engine
Multi-Speed Transmission

Location : USA

Worldrigs ID: WR153

Model : 3000-CF Drill Rig
Manufacturer : Failing
Condition : Used

Description :

Failing / Gefco Holemaster 3000-CF Drill Rig
Factory Rated Capacity: 3,700 ft. depth using 3-1/2” drill pipe.
Mast: Cold drawn street tubing, elec. Welded, 3-sect. with 3-way taper on top sect.
Hydraulically raised & lowered. Wired for elec. Lights. Equipped w/retracting
channel swivel guides for reverse circulation swivel. Equipped with ladder,
climber’s safety device.
 

Hgt. 72” Telescoping, Width 86” center to center of mast legs, Depth 48” center
to center of mast legs, Capacity total gross 133,000 lbs. hook load 100,000 lbs.
Racking board capacity 3,000 ft. of 3-1/2” drill pipe, may be mounted to pull 30' ft.
or 40' ft. joints, Crown block….. 6 trip line sheaves, 6 kelly line sheaves & single
sand line sheaf.

Draw works: Drum barrel dia. & length (Trip drum 10” x 13”) (Kelly drum 8” x 17”) maximum single
line pull first wrap (Trip drum 16,600 lbs. w/6 line block) (Kelly drum 16,600 lbs. 3/4” x 525’)
Line dia. & capacity (Trip drum 3/4” x 525’ ft) (Kelly drum 16,600 lbs. 3/4” x 525’ ft) Brakes,
mechanical lugh-leverage type, double self-energized & equalized (Trip drum 27” x 7”)
(Kelly drum 24” x 7”). Auxiliary brake: 15” double rotor parkers none Parkersburg. Catheads, 2,
mounted each end of Kelly drum shaft. One special air actuated for spinning or breakout, mounted
on driller”s side. One foster automatic cathead mounted on opposite side.
 

Rotary Table: Fully enclosed, oil bath type. Spiral bevel gears, ground & lapped in matched sets.
Opening 18” through table for setting casing. Hinges up to allow setting casing up to 34” O.D.
Rotary table, drum & sand reel, 5 forward & 1 reverse.
Air Compressors: for control air….1 or 2 Wabco model 2 AVC mounted on compound case.
For developing wells, ect….model 253-S2 or 50 SDS or equivalent may be installed
on the gooseneck.
 

Engines: 2, each providing 100 continuous BHP, through 17-1/2" fluid couplings,
GM diesel 4031-C is standard; other makes with suitable specs. may be installed.
Compound Case: Engines may be compounded or used singly. Oil spray bath, three shaft, w/jaw clutch.

Transmission: 5 speeds forward….7.20:1, 3.90: 1:2, 12:1:1, 18:1:1, 00:1. 1 speed reverse….7.09:1.
Clutches: Hoisting drum….2 Fawick 18CB500 air clutches; 18”. Kelly drum…. 2 Fawick 21.5E475 air
clutches. 21-1/2”. Rotary table….twin disc CL-211 air actuated clutch. Master clutch….lipe-roll
way 14”; 2 plate. Engines: twin disc 11”; 2 plate. Air Compressor….twin disc 11”; 3-plate.
Controls: Located on side at left of drawworks. Air valve control panel; remote transmission
shifter; throttle; trip & Kelly brakes; hydraulic control & pressure gauge; instrument
panel for engines; weight indicator & driller’s platform.
 

Other Units Cost Extra or Included as a Rig Package:
- Main Generator-60KW, 54KW prime, 2002 Caterpillar model XQ60P2
- Blowout prevention & well control equipment - 8” 3M Regan “Torus” angular preventer 2”
5M Demco valve on side outlet spool, 2” 5M manifold w/adjustable chokes.
- Doghouse/Toolhouse-8” x 36” trailer mounted.
- Substructure-4” w/pony sub.
- Back-up Mud Pump-Ideco 6” x 12” with 325 HP diesel engine.
- (135) Drill Pipe = 4,500’ ft (4-1/2").
- Drill Collars-150’ ft x 6”.
- Survey Machine-Mathey Wireline unit 12,000’ ft with .092 line.
 

Located : Africa

Worldrigs ID: WR833
Description :

2011 Atlas Copco RD20 Range III Drill Rig
Cummins KTAA19 (2019 Model) Diesel Deck Engine 800 Hours
IR HR2.5 1250 cfm / 350 psi Air Compressor
Mounted on CCC (Crane Carrier Company) Truck
Diesel Engine
Currently Working

Location : Middle East Region

Worldrigs ID: WR694
Model : 650 S/S Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic Model 650 S/S Drill Rig
No Engine currently on deck, but 2 spare Caterpillar 3406 diesel
engines are included
- 1 engine is said to have been rebuilt but we have not tested
- 2nd engine has a hole in block but will also be given with drill so
  you may salvage other parts from it as needed
750 CFM / 125 PSI C05 Air Compressor
Dynex main pump, Dynex Head motor
Gearmatic Hydraulic winch
27,500 lb. pullback capability
DTH Hammer oiler (lubricator included but needs re-installed)
4-hole Funk Box (hydraulic pump drive)
6-pod drill pipe carousel (needs re-assembled and re-installed)
3 Hydraulic jacks
3 pieces of 25 ft. drill pipe included
Mounted on a 1978 CCC (Crane Carrier Company) truck
powered by Caterpillar 3208 diesel engine - showing only 5136 miles on
odometer
Carrier hood and fender need re-installed, comes with spare on-road fuel tank

Location : USA

Worldrigs ID: WR684
Model : B61 HDX Drill Rig
Manufacturer : Mobile
Year : 1990
Condition : Used

Description :

1990 Mobile B61 HDX Drill Rig
Moyno water pump
Cummins Diesel deck engine
Detroit 671 T Diesel Engine in truck
140 lb. Safety Hammer
100 ft 6-5/8” augers
rods, bits, etc. included

Location : USA

Worldrigs ID: WR680
Model : 600-30 Foundation Drill Rig
Manufacturer : Texoma
Year : 1984
Condition : Used

Description :

1984 Texoma 600-30 Foundation Drill Rig
Engine: Cummings 6BTA 5.9 (Manufacture date of 10/26/1989) & (originally GMC Detroit Diesel)
Model: 5043-7001
Type: Wet bar
Drill Depth: 30 ft
Tier: 0
Steel track mounted
Condition: Runs great mechanically and only needs a little TLC. No major problems.
Height 47 ft x Width - 10ft-2" & Weight 52,000 lbs.
Torque 38,000 ft.-lbs.
Drilling Depth - 33 ft.

Location : USA

Worldrigs ID: WR216

Model : T450 Drill Rig
Manufacturer : Schramm
Year : 1988
Condition : Used

Description :

1988 Schramm T450 Drill Rig
Diesel Deck Engine
Air Compressor
Carousel
Centrifugal Pump
Pipe Rack
3 hydraulic leveling jacks
Mounted on a Truck
Diesel Engine

Location : USA

Worldrigs ID: WR779
Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : As-Is

Description :

Chicago Pneumatic T650 Drill Rig
Mounted on a 6 x 6 Oshkosh Truck
Modified drill rig
Direct drive off of the truck engine
900 cfm / 350 psi air compressor

Location : USA

Worldrigs ID: WR864
Description :

2017 Mobile B37X Crawler Drill Rig
600 Hours
8,000 ft/lb
1050 RPM
13 ft stroke
Auto hammer
308 Undercarriage
20,000 lb main winch
Bean 1122 pump
1,000 psi piping
Wireless
John Deere 140HP- tier 3
Angle Drill

Selling Fully Tooled:
44 lightly used 4 1/4 HS augers
820 ft NQ rods
20 ft Longyear barrel
10 ft HQ barrel
190 ft of AWJ rods

Location : USA

Worldrigs ID: WR776
Model : SDC500-29P Drill Rig
Manufacturer : Sonic
Condition : Used

Description :

Sonic SDC500-29P Drill Rig
80k Diedrich head
28ft stroke, 37ft 8" overall
24k pullback 16k pull down
12k 5/8" x 222ft nonrotating winch
4"-13" nominal clamping break out table
Hydrostatic circuit 4500PSI
pilot control
micro feed
float
high/low feed
120gal hydraulic tank
Mounted on a 2004 International 7600 6x4 Truck
Cummins ISM 320V upgraded ECM - rated 385hp
A45/1450 ft torque
Eaton Fuller 13 speed transmission
Hendrickson 38k rear axles
11R22.5 tires
FMC bean pump
3L6 Moyno
Head #A0012 Rebuilt 7/16/10, 9/30/12, 7/23/18 (upgraded roller bearings)
Rebuilt Transmission 8/19/17
Rebuilt winch 8/23/17
Odometer 104,651 miles / 9,374 Hours

Location : USA

Worldrigs ID: WR866
Description :

Davey Rouselle M8A Drill Rig
Mounted on a 1991 Sterling truck
CAT 3306 Diesel Engine
8 speed transmission
Davey 500 cfm / 125 psi piston compressor (also plumbed for auxiliary air)
Included with 100 ft of Davey rods and a changeover sub to 3.5" API threads for bit

Note: Since 2018 the drill has had the air compressor "gone through", has had
the table replaced, Ramsey pulldown winch replaced, chain cases replaced,
table transmission rebuilt, new radiator for deck engine, and various other
small repairs done
Drill motor is getting weak and will need rebuilt and can be done here if needed
and the price would reflect that
Truck Runs fine but 4th gear does jump out

Location : USA

Worldrigs ID: WR700
Model : T660W Drill Rig
Manufacturer : Schramm
Year : 1996
Condition : Used

Description :

1996 Schramm T660W Drill Rig
Deutz Tier III Diesel Deck Engine (350-400 hours since new)
Sullair 900 CFM / 350 Air Compressor - rated 1900 RPM
Bean Water Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Hydraulic Pull Down & Pull Back
Hydraulic Cooler
Equipped with two extra hydraulic Ram to operate casing hammer 4-1⁄2” x 25 ft
Drill Steel
3 Outriggers
Complete Part & Service / Repair Manual
Breakout Wrench
Hydraulic Grout Pump
Cyclone Dust Control
Hydraulic Adj Jib & Rotation Jib
Extra Sandline Winch
Multiple speed top head motors
Mounted on a Ford L8000 Truck
Cummins 6CTAA 8.3L Diesel Engine - S/N: 60312850 & PIN#:3802644-PX
(newer engine installed with 7,000 miles since) - Rated 250 HP at 2200 RPM
(Reman Plate numbers: 3922471LA & M051807002B & P-7100).
Air & Mud Drilling Capabilities

Location : USA

Worldrigs ID: WR881
Description :

2003 Schramm T450 Crawler Drill Rig
Serial Number : J102-B236
Sullair 900 CFM / 350 PSI Air Compressor (serial number: 004-005820) - rated
1800 RPM
Caterpillar 3406B diesel deck engine
Hour meter shows 10,360 hours
Proheat Engine Heater
Bean FMC 2 Cylinder water injection pump
6 Rod Carousel
Graco Hammer Oiler
Pullback: 30,000 lb (13,608 kg)
16.5 inch table opening
Crawler mounted (note: can be mounted on a 2005 Kenworth double frame truck)

Location : USA

Worldrigs ID: WR833
Description :

2011 Atlas Copco RD20 Range III Drill Rig
Cummins KTAA19 (2019 Model) Diesel Deck Engine 800 Hours
IR HR2.5 1250 cfm / 350 psi Air Compressor
Mounted on CCC (Crane Carrier Company) Truck
Diesel Engine
Currently Working

Location : Middle East Region

Worldrigs ID: WR768
Model : D120 Drill Rig
Manufacturer : Diedrich
Year : 1991
Condition : Used

Description :

1991 Dierich D120 Drill Rig
John Deere inline 6 diesel Serial #: T06059D43379
990.3 Hours
Moyno 3L8 Pump
500 gallon water tank, Cathead, Fluted kelly, (2) auger racks
Tool boxes, (4) outriggers, 3k, 7k, 10k Winches
Mounted on a 2001 Sterling AT9513 Truck
10 Speed Transmission
Odometer 578,364 miles

Location : USA

Worldrigs ID: WR779
Model : T650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : As-Is

Description :

Chicago Pneumatic T650 Drill Rig
Mounted on a 6 x 6 Oshkosh Truck
Modified drill rig
Direct drive off of the truck engine
900 cfm / 350 psi air compressor

Location : USA

Worldrigs ID: WR77

Model : T-555
Manufacturer : Schramm
Year : 2002
Condition : Used

Description :

2002 Schramm T-555 Drill Rig
Sullair 1070 CFM / 500 PSI Air compressor,
75,348 in lbs torque @ 0-131 RPM,
40,000 pullback,
30,000 pulldown.
CAT C-15 DIT Diesel Deck Engine @ 565 HP with 6,326 Hours
18 GPM Bean water pump
280' ft of (4 1/2 rod with 3 1/2 IF pin, box ends).
Note: can hold 300' ft in the rod box and can run 20" Casing pipe
DTH oilier, Sandline Semco S6
Hydraulic swing and extend Jib boom
Secondary winch Pullmaster M8-3-30-1
Primary winch
Mounted on a 2002 International 2674 Truck
Powered by Cummins ISM370 Diesel Engine
21,529 miles

Location : USA

Worldrigs ID: WR872
Description :

PortaDrill 524 Drill Rig
5 Leveling Jacks
7-1/2" Retractable Rotary Table
26ft Kelly
3 Line Machine (Sand Line & Kelly)
2" Little Giant Swivel
Racking Board
Note: No Rod Included

Location : USA

Worldrigs ID: WR597
Model : T-650 Blast Hole Drill Rig
Manufacturer : Reichdrill
Year : 1989
Condition : Used

Description :

1989 Reichdrill T-650 Blast Hole Drill Rig
1100 CFM / 350 PSI Air Compressor
Rebuilt Cummins KT Diesel Engine
Mounted on an International truck
Rebuilt - Cummins L10 Diesel Engine
DTH Hammer included

Location : USA

Worldrigs ID: WR629
Model : T985 Drill Rig
Manufacturer : Schramm
Condition : Used

Description :

Schramm T985 Drill Rig
Dual 425 CFM / 250 PSI Air Compressors
Dual Detroit Diesel Engines
Mounted on a twin axle CCC Truck
Diesel Engine
Working Order

Location : USA

Worldrigs ID: WR885
Description :

1986 Jaswell J1200 Drill Rig
Mounted on a 1986 International Paystar 5000 Truck
Cummins 350 HP diesel engine  
20 speed spicer transmission
20k front axle & 44k rear axles
Odometer works and reads 96,000 miles
90% rubber all around
Cummins N14 mechanical - rated at 450 HP diesel engine
Sullair 900 cfm / 350 psi air compressor with cooler mounted on the side

Comes with : 360 ft of drill steel, two 6" hammers, and 8" hammer stabilizer
6" QL60 Hammer and the 8" Hammer & 8-1/2" Bit. All hand tools included
New diamond chains top and bottom, new sprockets, pins and bushings in 2018
Rebuilt twin disc pto in 2018. Replaced rear main seal in the deck engine 2018
New crown shaft in 2018, pillow block bearings were used but in good condition
Two piston bean pump. Tube style tower same as J2400
1000 hours on it since repairs in 2018

Location : North America

Worldrigs ID: WR781
Model : DSI QuikDrill Rig
Manufacturer : Speedstar
Condition : Used

Description :

Speedstar DSI QuikDrill
Failing FM-3 Mud Pump
Has Air Compressor (Not Working)
Mounted on 2001 International 4900 Truck
Powered by 7.6 L 466 CID L6 International DT466 Diesel Engine

Location : USA

Worldrigs ID: WR879
Description :

1979 Chicago Pneumatic 600 Drill Rig
Detroit 6V93 Diesel Deck Engine
GHH 600 CFM / 300 PSI Air Compressor
320 ft of 4-1/2" x 20 ft Drill Pipe included
Recent Cooler and Drill Head Rebuilt
Mounted on a 1990 Mack Truck
300 HP Diesel Engine

Location : USA

Worldrigs ID: WR846
Description :

2013 Schramm TXD Drill Rig
API Certified Rig
23,635 Hours
Mounted on a Trailer

Items Available for Additional Cost:
Loadsafe System and Pad
Drill Pipe
Collars
Handeling Tools
Doghouse
Air Compressors
Mud Pumps
Pits
Shakers

Location : USA

Worldrigs ID: WR352

Model: 45C Drill Rig
Manufacturer: CME Drill
Year: 2002
Condition: Used

Description :

2002 CME 45C Drill Rig
With 9278 hours
Auto hammer
Wireline winch
Deutz 3 cylinder diesel engine
Mounted on a 2002 Ford F550 Truck 4x4
148,413 miles

Location : USA

Worldrigs ID: WR842
Description :

2002 Ingersoll-Rand T4W Drill Rig
Cummins QSK-19-C Diesel Deck Engine (rated 600 HP at 2100 RPM)
IR HR2.5 1070 cfm / 350 psi Air Compressor
Mounted on a CCC (Crane Carrier)
CAT C-10 Diesel Engine
50,000 lbs of Pullback
Dual Motor Planetary Head
Setup for 2-7/8" IF Drill Rod
Recently painted silver and red

Additional Tooling :
6” IR QL60 Drive Hammer with Bit
6” IR QL60 Drill Hammer with 4-1/2” x 21.5ft heavy wall lead steel with bit
8” IR QL80 Drill Hammer with 6” x 20ft lead steel with bit
4-1/2” X 25ft 2-7/8 API Drill Rod (11 pieces)
6” Casing Drive Plate
8” Casing Drive Plate
10” Casing Drive Plate
1 - Petol Chain Wrench set up for 4-1/2” Drill Rod and 6” Hammer
1 – Petol Chain Wrench set up for 6” Drill Rod and 8” Hammer
Miller Welder with Leads
Oxy/Acetalene Torch Setup

Location : USA

Worldrigs ID: WR886
Description :

2012 Schramm TXD 200 Drill Rig
serial number J135-0216, trailer VIN#: 1K9AD40C1C3268138.
Detroit DDC/MTU 12V-2000 Diesel Deck Engine

Tilt Top Head Drive:
Heavy duty, single reduction gearbox with 4 two-speed disc valve type 
hydraulic motors
Variable rotation speed via HRC control
Torque: 0-90 RPM @ 17,750 ft-lbs (24,066 N-m)
0-180 RPM @ 7,670 ft-lbs (10,399 N-m)
Rotation Speed: 0 - 180 RPM · 

Feed System:
50 ft (15.24 M) head travel
200,000 lbf (890 kN) hoist capacity
100 fpm (30.5 m/min) hoist speed
32,000 lbf (142 kN) pulldown
200 fpm (61 m/min) pulldown speed

Drill Table:
Table Opening : 30" inches (768 mm) diameter with table retracted
Hydraulically retractable slip box

Drill Pipe And Casing:
Range III tubular 30 inch capability

Winch:
Planetary design with spring applied hydraulic release brake
9,600 lbf (42.7 kN) bare drum line pull
150 fpm (46 m/min) bare drum line speed
Hydraulic jib boom swing and extend
Auxiliary winch available
The drills have low wear on the cables, bearing and pivot points as well 
as the Control panel
All are in excellent/very good condition during last inspection
LoadSafe pipe handling systems (hands free pipe loading system)
mounted on Trailers

Package available  each of the following:
Generator House with 2 Maraathon Model 431CSL6202-B211 60 HZ Phase 1 
120/240V 122 KW 504 AMO or 3 Phase 277/480 155 KW 233 AMP poered by 
Perkins 6.6 L 1106 IR 2340 Shop air ,Hyd lift with Honda GX392,4000 Gallon 
feul tank and 4 lights on roof.
Weatherford T425 Triplex Mud pump powered by John Deere 6135 diesel engine 
(Tier IV) - rated 500 HP, 6.50 Plunger 900 PSI, MCM 4x5x14 Super Charge 
Centrifugal pump with soap mixing tanks in back
750 BBL Water tank with hydraulic lift dog house
Crew changing house
Crew House 
8000 ft of drill pipe (4" DP New 30ft 6" NC40)
(4) 6-1/2” Drill collars
Every unit is clean & straight and it is a very nice package in excellent/very 
good condition after inspections in 2020

Location : USA

Worldrigs ID: WR700
Model : T660W Drill Rig
Manufacturer : Schramm
Year : 1996
Condition : Used

Description :

1996 Schramm T660W Drill Rig
Deutz Tier III Diesel Deck Engine (350-400 hours since new)
Sullair 900 CFM / 350 Air Compressor - rated 1900 RPM
Bean Water Injection Pump
Two Winch Lines
36” Mast (Autofeed)
Hydraulic Pull Down & Pull Back
Hydraulic Cooler
Equipped with two extra hydraulic Ram to operate casing hammer 4-1⁄2” x 25 ft
Drill Steel
3 Outriggers
Complete Part & Service / Repair Manual
Breakout Wrench
Hydraulic Grout Pump
Cyclone Dust Control
Hydraulic Adj Jib & Rotation Jib
Extra Sandline Winch
Multiple speed top head motors
Mounted on a Ford L8000 Truck
Cummins 6CTAA 8.3L Diesel Engine - S/N: 60312850 & PIN#:3802644-PX
(newer engine installed with 7,000 miles since) - Rated 250 HP at 2200 RPM
(Reman Plate numbers: 3922471LA & M051807002B & P-7100).
Air & Mud Drilling Capabilities

Location : USA

Worldrigs ID: WR546

Model : D40K Drill Rig
Manufacturer : Driltech
Condition : Used

Description :

Driltech D40K Drill Rig
50,000 lbs of pullback
high torque head
No carousels (removed for large diameter Well drilling)
dual winches 6000k single line
18000K single line hydraulic Denison P7 main pump - replaced early p-5
All pumps where rebuilt or replaced in 2015 including main gearbox rebuild
Replaced / upgraded to Mercedes tier 4 (I) 550hp diesel deck motor
900 CFM / 300 PSI air compressor
has a mud line and a true 3" mud swivel added to it so it's "mud ready"
New in 2015 radiator/engine cooler rated at 450hp Additional hydraulic cooler added
Mounted on 2012KW tier 4 435hp Paccar heavy spec truck
dual steering and full locking rears
Heavy duty engine Brake
Rig needs a few new hydraulic hoses and new paint job
Note: this machine is 100% California CARB compliant

Location : USA
 

Worldrigs ID: WR494

Model : 650 Drill Rig
Manufacturer : Chicago Pneumatic
Condition : Used

Description :

Chicago-Pneumatic 650 Drill Rig
CP 450 CFM / 250 PSI Piston Compressor with 750/350(?)
Booster (air clutch needs newdiapragm)
Tiger Tierra Casing Driver
Carousel

Package Includes:
300’ ft of used drill pipe (some need new pins and boxes)
6” and 9” DTH Hammers
6” Tricone button bit

Spare Parts included; main pumps, top head motors, inner cooler, valves for
the compressor, new drive chain for the transfer case

Rig in working order, some oil leaks (packings need replaced).
Mounted on a 1973 International Paystar truck

Location : USA

Worldrigs ID: WR597
Model : T-650 Blast Hole Drill Rig
Manufacturer : Reichdrill
Year : 1989
Condition : Used

Description :

1989 Reichdrill T-650 Blast Hole Drill Rig
1100 CFM / 350 PSI Air Compressor
Rebuilt Cummins KT Diesel Engine
Mounted on an International truck
Rebuilt - Cummins L10 Diesel Engine
DTH Hammer included

Location : USA

Worldrigs ID: WR674
Model : T670W Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1979
Condition : Used

Description :

979 Chicago Pneumatic T-670W Drill Rig
Loader Lock Carousel
Breakout Wrench
20 ft x 4-1/4” of used Drill Pipe
CAT 343 V6 Diesel Deck Engine (Turbo)
425 cfm / 250 psi Air Compressor
Oil Lube Pump
Bean Water Injection Pump - 1267611
Hydraulic Winch Line
3 Outriggers
Hydraulic Pull Down & Pull Back
Autofeed
18” Table Opening
320 ft of Pipe Trough
7 Rod Carousel
Auto Rod Loader
Complete Part & Service / Repair Manual Hydraulic Jib
Hydraulic Adjustable Jib Arm
Setup for AIR and MUD Drilling
Mounted on G.M.C. 7500 Series
Detroit 6V-53 Diesel Engine

Location : USA

Worldrigs ID: WR557

SOLD
Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1989
Condition : Used

Description

1989 Ingersoll Rand T3W Drill Rig - S/N: 2900
IR 825 cfm / 350 psi Air Compressor
Caterpillar 3406 diesel deck engine
3636 hours showing on meter (probably turned over & actual
hours might be 13,636)

Sand line winch
Cat water injection pump
Hammer Lubricator
Hydraulic Leveling Jacks
Mounted on a 1989 Ford L8000 Truck
Diesel Engine
74,321 miles

Location : USA

Worldrigs ID: WR861
Description :

Schramm T130 Drill Rig
Diesel Deck Engine
Mounted on a CCC Truck
Diesel Engine

Included as a package:
4-1/2" Bottle Neck X Hole Drill Pipe
6" Collars = 90 ft
All Subs needed to drill
Spare Motor
Spare Parts : Top Drive (Rebuilt no hours), New Spindle,
Bearings for top drive, Chive Crown
Pipe Racks with Catwalk (30 ft L X 5 ft W X 3-1/2 ft T)

Location : USA

Worldrigs ID: WR783
Model : Simco-Style Top Head Drive Drill Rig
Manufacturer : Generic
Condition : Used

Description :

Simco-Style Top Head Drive Rotary Drill Rig
Simco Swing-Away Top Rotary Hydraulic Power Head
Swivel
16 ft. 4 in. mast length (retracted), approximately 25 ft. length mast (extended)
Rod Box
Cathead
Winch
4 cylinder Deutz Deck Engine
Control Panel
Mounted on a Ford F600 diesel powered truck
4 Hydraulic stabilizing jacks
Clean, ready-to-work machine

Location : USA

Worldrigs ID: WR805

SOLD

Model : T3W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 2004
Condition : Used

Description :

2004 Ingersoll-Rand T3W Drill Rig
Engine Hours: 20,621
50 ft – 45,000lb static hook load capacity
hydraulic raise/lower mast
Atlas Topco top drive
Braden 23,000 lb winch
mud system (5” x 6” or 5.5” x 8” GD mud pump)
hydraulic set up to run two pumps or air compressor
hydraulic hoses are re-conditioned
rig derrick can be shortened if requested

Note: no deck engine or air compressor on board the drill
Mounted on International 5600i Truck
Cummins ISX 14.9L Engine
475 Adv horsepower
engine brake
Eaton Fuller 18 speed manual transmission
330” wheel base
8 X 6 20,000lb front axle
54,000lb rears

Location : North America

 

Worldrigs ID: WR851
Description :

1979 Portadrill TLS Top Head Drill Rig
60k main line of pullback
40k Tophead Power Drive (swing out)
Sandline
Detroit 8V92TA deisel deck engine
750 cfm / 250 psi air compressor
Leveling jacks
Mounted on an International Truck
Deisel engine
Rebuilt 3 years ago
3 inch western rubber swivel
Retractable table
Note: capable of 16” well with 28” bore
Note: needs paints and leaks fixed (cost extra)

Location : USA

Worldrigs ID: WR695
Model : 650 S/S Drill Rig
Manufacturer : Chicago Pneumatic
Year : 1978
Condition : Used

Description :

1978 Chicago-Pneumatic Model 650 S/S Drill Rig
Caterpillar 3406 diesel engine - serial number 9HB03011
Near new batteries
750 CFM / 125 PSI CO5 Air Compressor
Dynex main pump & Dynex Head motor
Hydraulic winch
27,500 lb. pullback capability
DTH Hammer oiler
4-hole Funk Box (hydraulic pump drive)
REICHdrill dust collector (can be removed if needed)
Operators cab (can be removed if needed)
6-pod drill pipe carousel
Comes with 3 near-new 25 ft. x 5 in. OD drill pipes
New head adapter
New bit sub (tricone bit not included)
3 Hydraulic jacks
Mounted on a 1978 FCCC (Crane Carrier Company) truck
powered by Caterpillar 3208 diesel engine
13-speed Roadranger transmission
showing only 3934 miles on odometer
We also have used 25 ft. length x 4-1/2 in. OD x 3-1/2 in. API Regular
drill pipe available which can be sold at an extra cost, if needed.

Location : USA

Worldrigs ID: WR662
Model : T25K3W Drill Rig
Manufacturer : Driltech
Year : 1994
Condition : Used

Description :

1994 Driltech T25K3W Drill Rig- S/N: 731889
Sullair 840 cfm / 350 psi Air Compressor
CAT 3406 DITA Diesel Deck Engine - rated 430 HP @ 1,800 RPM
30,000 LBS of Pullback
28 ft Head Travel
Pipe Rack Holds For 15 Pipe
(6) Rod Carousel
Rotary Head - rated 89 RPM & 62,600 in LBS. Torque
Jib Boom, Hydraulic Extend With 172 Degree Hydraulic Swing
Hydraulic Winch 7,500 LBS. Capacity
20" Openiing in Table With Hydraulic Adjustment
48" Jaw Type Breakout Wrench
Water Injection Pump is 20 GPM With Foam Pump
DTH Lubricator With 10 Gallon Tank
Fine Feed  & Torque Controls
420 ft. of Used Drill Pipe (4-1/2" O.D. X 20ft) & Basic Tooling Included
Gardner Denver 5 X 6 Air Drive Mud Pump on Board
Hydraulic Leveling Jacks
Mounted on a 1993 Ford LNT8000 - VIN #1FDZW82E0PVA18231
Cummins 8.3l 275 Hp Diesel Engine
10 Speed Transmission
18,000 Front Axle
46,000 Rear Axle

Location : USA

Worldrigs ID: WR469

Model : T450GT Drill Rig
Manufacturer : Schramm
Year : 2008
Condition : Used

Description :

2008 Schramm T450GT Crawler Drill Rig
Caterpillar C-15 diesel engine @ 580 HP - S/N JRE09405
Sullair 1050 cfm / 350 psi air compressor with clutch
Floating sub
15 Rod Carousel - handles 3-1/2" Pipe
500' ft of 3-1/2" x 20' x 2-3/8" IF thread (estimated 50% condition)
Washington diverter
Hydraulic welder
Hammer lubricator
4 piston water injection pump
Rod spinner
2 motor power head
6,440 hours on gauge

Location : USA

Worldrigs ID: WR859
Description :

1978 Portadrill 524-3A Drill Rig
Gardner-Denver 5-1/2" Mud Pump
Leroi 256 S-2 250 PSI Air Compressor
Hydrostatic drawworks and rotary table
Pipe Slide
Injection pump
Hydraulic leveling jacks
Mounted on a 1999 Ford Louisville truck
Powered by Cummins Red Top N14 Diesel Engine - rated 500 HP
Tag axle

Location : USA

Worldrigs ID: WR882
Description :

1979 Ingersoll-Rand TH60 Drill Rig,
IR 750 CFM / 250 PSI Air Compressor,
Water injection pump,
Toolbox,
Carousel,
4 hydraulic leveling jacks,
Comes with 420ft Drill Pipe 4-1/2" 2-7/8 IF Thread
Mounted on a 1986 GMC General Truck,
Powered 8V92 Detroit Diesel 475 HP,
All drums & brakes good & Tires 80% estimated,

Location : USA

Worldrigs ID: WR464

Model : 1500 Drill Rig
Manufacturer : Howard Turner
Condition : As-Is

Description :

Howard Turner 1500 Drill Rig
Mounted on a Truck
Diesel Engine
HT rotary table drive
Note: Selling the drill rig "as is" to a collector

Location : USA

Worldrigs ID: WR492
Speedstar S S61A Cable Tool Rig Details:

Worldrigs ID: WR771
Model : HTB3KDD Drill Rig
Manufacturer : Howard Turner
Year : 2008
Condition : Used

Description :

2008 Howard Turner HTB3KDD Drill Rig Package
CAT C-7 Diesel Engine - rated 260 BHP
6 Cylinder Diesel 2000 MOD NEW
ALLISON-GM MOD # 653
Drawworks :
H.T.B. CANTON TX.
MOD # HTB5KDD - MUSTANG
Clutches - PO3-10
Twin Disk Brakes - 8 x 28 2 per drum
Drums - 14"
Drums - lea bus for 3/4" cable
Drum Drive - 350 hp deran r-angel
25,000 single line pull to 40,000 lbs
Double 120 Chain
Mast : 62ft X 6ft X 3ft HTB - 150,000 #
Carrier : 50ft tandem axle
Swivel : 72 Ton - 144,000 Pounds
JIB Winch
Hydraulics : 20 gpm, 2000 psi. | PTO Driven from Allison Transmission
Drilling Depth : 6,000 feet
Hours : 3087

Extra Item Available(for extra cost) :
2000 Mud Cleaning System FXZ Gardner Denver mud pump
Mounted on a TRA 48ft Trailer 2000 Olympian 60 kW Generator (8,376 Hours)
1990 Ford 9000 - Equipped with winch for loading pipes
Trailer designed for loading pipes with HTB Drilling Rig sold with
2000ft pipes (5” Drill pipe whith 3.5 IF con/ 13.30 lbs)
Tiger 500 Gallon Fuel Tank
Drill colars 6′′ x 28ft ( 2pcs)
3 1⁄2" bottel neck elevators
Pipe Elevators
Drag bit
Tricone bit
Rods 3-1/2′′ x 30ft
Trush Pump
Casing Elevator
Bit 26"
Sub-base

Location : USA

Worldrigs ID: WR696
Model : T4W Drill Rig
Manufacturer : Ingersoll-Rand
Year : 1974
Condition : Used

Description :

1974 Ingersoll-Rand T4W Drill Rig
Detroit V12 Diesel Deck Engine (inframe rebuilt)
IR HP 750 CFM / 250 Air Compressor
Water Injection Pump
Oil Injection Pump
Two Winch Lines
Carousel
36” Mast (Autofeed)
Pull Down & Pull Back
18” Table Opening
Worm Gear Top Head
Hydraulic Cooler
Rod Changer
Handles 4-½” x 25ft Drill Pipe
3 Outriggers
Complete Part & Service / Repair Manual
Breakout Wrench
Hydraulic Jib
Setup for AIR and MUD Drilling
Slow & Fast Rotation
Mounted on a CCC (Crane Carrier Company) Truck
Diesel Engine

Location : USA

Worldrigs ID: WR787
Model : 2800 Drill Rig
Manufacturer : Simco
Condition : Used

Description :

Simco 2800 Auger Drill - Unmounted
Year: 1976 / 1977
Dual Motor Hydraulic Top Rotary Power Head (swings away)
11 ft. 6 in. mast (retracted), approximately 18 ft. mast extended
Cathead
Winch
Wisconsin 4 cylindergas motor
In working order
Currently unmounted but comes with trailer it was previously mounted on
included in deal

Location : USA

Worldrigs ID: WR864
Description :

2017 Mobile B37X Crawler Drill Rig
600 Hours
8,000 ft/lb
1050 RPM
13 ft stroke
Auto hammer
308 Undercarriage
20,000 lb main winch
Bean 1122 pump
1,000 psi piping
Wireless
John Deere 140HP- tier 3
Angle Drill

Selling Fully Tooled:
44 lightly used 4 1/4 HS augers
820 ft NQ rods
20 ft Longyear barrel
10 ft HQ barrel
190 ft of AWJ rods

Location : USA